Yamaha RDX-E700 User manual

SERVICE MANUAL
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA
Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and
specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the
distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
IMPORTANT NOTICE
SERVICE MANUAL
TRAY LOCK MODE / トレーロックモード ......... 12
FACTORY RESET / ファクトリーリセット ......... 12
PRINTED CIRCUIT BOARD . . . . . . . . . . . . . . . .13–16
BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . .18–23
RDX-E700 EXPLODED VIEW . . . . . . . . . . . . . . . . . .24
RDX-E700 MECHANICAL PARTS . . . . . . . . . . .25–26
NX-E700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . .28–29
■ CONTENTS
TO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . .2–4
PREVENTION OF ELECTRO STATIC DISCHARGE . . . . . . 4
LOCALE MANAGEMENT INFORMATION . . . . . . . .5
FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
REMOTE CONTROL PANELS . . . . . . . . . . . . . . . . . .6
REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
SPECIFICATIONS / 参考仕様 . . . . . . . . . . . . . . . . . .8–9
DIMENSIONS / 寸法図 . . . . . . . . . . . . . . . . . . . . . . . . .9
INTERNAL VIEW / 各部名称 . . . . . . . . . . . . . . . . . . . .10
RDX-E700 DISASSEMBLY PROCEDURES /
RDX-E700分解手順 . . . . . . . . . . . . . . . . . . . . . . .10–11
100991 © 2005 YAMAHA CORPORATION. All rights reseved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
’05.11
RDX-E700/ NX-E700
MICRO COMPONENT SYSTEM MCR-E700
RDX-E700
NX-E700
The MCR-E700 consists of the RDX-E700 and the NX-E700.
  

2
RDX-E700/NX-E700
RDX-E700
NX-E700
■ TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked Z
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●Meter impedance should be equivalent to 1500 ohms shunted
by 0.15µF.
AC LEAKAGE
TESTER OR
EQUIVALENT
EQUIPMENT
UNDER TEST
INSULATING
TABLE
WALL
OUTLET
●Leakage current must not exceed 0.5mA.
●Be sure to test for leakage with the AC plug in both
polarities.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or
plastic (where applicable) components may also contain traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR
ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes
or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands
before handling food.
About Lead Free Solder / 無鉛ハンダについて
The P.C.B.s installed in this unit are soldered using the fol-
lowing solder. 本機に搭載されている基板のハンダ付けに使用されている ハンダは下記の通りです。
 
  
  
  
  
Side A
Side B
SMT REFLOW Process
MI FLOW Process
Solder Dip
Among some types of lead free solder currently available, it
is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
1. As the melting point temperature of the lead free solder is
about 30°C to 40°C (50°F to 70°F) higher than that of the
lead solder, be sure to use a soldering iron suitable to
each solder.
無鉛ハンダにはいくつかの種類がありますが、修理時には
下記のような無鉛ハンダの使用を推奨します。
・Sn+Ag+Cu（錫+ 銀+銅）
・Sn+Cu（錫+銅）
・Sn+Zn+Bi（錫+ 亜鉛+ビスマス）
注意：
1. 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30〜
40℃程度高くなっていますので、それぞれのハンダに
合ったハンダごてをご使用ください。

3
RDX-E700/NX-E700
RDX-E700
NX-E700
WARNING: Laser Safety
This product contains a laser beam component. This
component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes
and skin from laser radiation, the following precautions
must be used during servicing of the unit.
1) When testing and/or repairing any component within
the product, keep your eyes and skin more than 30 cm
away from the laser pick-up unit at all times. Do not
stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the
laser pick-up, unless noted elsewhere in this manual.
3) CAUTION : Use of controls, adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Laser Emitting conditions:
1) When the Top Cover is removed, and the STANDBY/
ON SW is turned to the "ON" position, the laser
component will emit a beam for several seconds to
detect if a disc is present. During this time (5-10 sec.)
the laser may radiate through the lens of the laser pick-
up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the
beam. When a disc is loaded, you will not be exposed
to any laser emissions.
2)The laser power level can be adjusted with the VR on
the pick-up PWB, however, this level has been set by
the factory prior to shipping from the factory. Do not
adjust this laser level control unless instruction is
provided elsewhere in this manual. Adjustment of this
control can increase the laser emission level from the
device.
警告：レーザーの安全対策
本機はレーザー光線を放射する部品を搭載しています。こ
の部品が放射するレーザー光線は目に損傷を起こします。
このレーザー光線から目及び肌を保護するために、本機の
修理作業中は下記の注意を厳守してください。
１）テスト時または修理時、目及び肌を光ピックアップか
ら30cｍ以上離してください。いかなる場合もレーザー
光線を見つめないでください。
２）光ピックアップの再調整及び分解はしないでください。
３）このマニュアル上で指定されている以外の制御、調整、
手順はレーザー光線を照射される結果を招く恐れがあ
ります。
レーザー放射条件
１）トップカバーを取り外しSTANDBY/ONスイッチをON
にすると、ディスク検知のため5〜10秒間、光ピック
アップからレーザー光線が放射されます。この間、修
理はしないでください。
ディスクが検知されなければ、レーザー光線の放射は
停止します。ディスクがセットされている場合、ディ
スクで遮られるのでレーザー光線は修理担当者に届き
ません。
２）レーザーパワーレベルは光ピックアップ基板上のVRに
より調整可能ですが、工場出荷前に調整セット済みな
ので、このVRは廻さないでください。このVRを廻す
と装置からのレーザー光線の放射レベルが上がる恐れ
があります。
2. If lead solder must be used, be sure to remove lead free
solder from each terminal section of the parts to be replaced
and from the area around it completely before soldering, or
make sure that the lead free solder and lead solder melt
together fully.
2. 鉛入りハンダを使わざるを得ない場合は、あらかじめ交
換する部品端子部やその周辺部の無鉛ハンダをすべて取
り除くか、あるいは無鉛ハンダと鉛入りハンダが十分に
溶けた状態となるようにハンダ付けしてください。
Laser Diode Properties
Type: Semiconductor laser GaAlAs
Wave length: 650 nm (DVD)
790 nm (VCD/CD)
Output Power: 1.45 mW (DVD)
1.13 mW (VCD/CD)
Beam divergence: 60 degree
VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LASER-SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
レーザー
タイプ 半導体レーザーGaAlAs
波長 650nm(DVD)
790nm(VCD/CD)
出力 1.45mW(DVD)
1.13mW(VCD/CD)
ビーム広がり 60度

4
RDX-E700/NX-E700
RDX-E700
NX-E700
■PREVENTION OF ELECTRO STATIC DISCHARGE
The laser diode in the DVD mechanism may be damaged due to static electricity from clothes or the human body.Use caution
to prevent electro static damage when servicing or handling the DVD-mechanism.
1. Grounding for electro static damage prevention
Some devices, such as the DVD player, use an optical pickup (laser diode) that will be damaged by static electricity in the
working environment.Only attempt service after ensuring that all grounding procedures have been completed.
1.Worktable grounding
Put a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.
2. Human body grounding
Use an anti-static wrist strap to discharge the static electricity from your body.
1MΩ
Conductive material
(sheet) or steel sheet
Anti-static wrist strap
2. Handling Precautions for DVD mechanism
1. Handle the DVD mechanism gently, as it is an extremely high-precision assembly.
2.The flexible cable lines may break if an excessive force is applied to it.Use caution when handling the cable.
3.The semi-fixed resistor for laser power adjustment should not be adjusted.Do not turn the resistor.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
AVERTISSEMENT
L’utilisation de commandes et l’emploi de réglages ou de
méthodes autres que ceux décrits ci-dessous, peuvent
entraîner une exposition à un rayonnement dangereux.
VORSICHT
Die Verwendung von Bedienelementen oder die Einstellung
bzw. die Ausführung von anderen als in dieser Anleitung
beschriebenen Vorgängen kann zu Gefährdung durch
gefährliche Strahlung führen.
OBSERVERA
Användning av reglage eller justeringar eller utförande av
åtgärder på annat sätt än så som beskrivs häri kan resultera i
farlig strålning.
ATTENZIONE
L’uso di controlli, regolazioni, operazioni o procedure non
specificati in questo manuale possono risultare in esposizione
a radiazioni pericolose.
PRECAUCIÓN
El uso de los controles, los ajustes o los procedimientos que
no se especifican en este manual pueden causar una
exposición peligrosa a la radiación.
LET OP
Gebruik van bedieningsorganen, instellingen of procedures
anders dan beschreven in dit document kan leiden tot
blootstelling aan gevaarlijke stralen.
ПРЕДОСТЕРЕЖЕНИЕ
Использование органов управления или
произведение настроек или выполнение процедур, не
указанных в данной инструкции, может отразиться на
выделении опасной радиации.
CLASS 1 LASER PRODUCT
LASERE KLASSE 1 PRODUKT
CAUTION-VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN. DO NOT
STARE INTO BEAM OR VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1

5
RDX-E700/NX-E700
RDX-E700
NX-E700
■LOCALE MANAGEMENT INFORMATION
Locale Management Information : This DVD player is designed and manufactured to respond to the Locale
Management Information that is recorded on a DVD disc. If the Locale number described on the DVD disc does not
correspond to the Locale number of this DVD player, this DVD player cannot play this disc.
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Macrovision Corporation and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
q
w
r
w
t
t
r
w
y
e
t
The MCR-E700 consists of the RDX-E700 and the NX-E700.
■SYSTEM COMPOSITION/システム構成
▼ NX-E700
▼ RDX-E700
▼ NX-E700

6
RDX-E700/NX-E700
RDX-E700
NX-E700
■FRONT PANEL
■REMOTE CONTROL PANELS
▼ U, C, T, K, A, L, V, J models ▼ B, G models

7
RDX-E700/NX-E700
RDX-E700
NX-E700
▼ V model
■REAR PANELS
▼ U, C models
▼ A model
▼ T model
▼ K model
▼ B, G models
▼ L model
▼ J model

8
RDX-E700/NX-E700
RDX-E700
NX-E700
U ........ USA model
C ........ Canadian model
T ........ Chinese model
K ........ Korean model
A ........ Australian model
B ........ British model
G ........ European model
L ........ Singapore model
V ........ Tiwanes & Mexican models
J ........ Japanese model
■SPECIFICATIONS/参考仕様
RDX-E700
AMPLIFIER SECTION / アンプ部
•Minimum RMS output power per channel (20 kHz Factory LPF) /

(6 ohoms, 1 kHz, 0.18% THD) . . . . . . . . . . . . . . . . . 20 W + 20 W
•Maximum RMS output power per channel (20 kHz Factory LPF) /

(6 ohoms, 1 kHz, 10% THD) . . . . . . . . . . . . . . . . . . . 30 W + 30 W
•Total Harmonic Distortion / 
AUX etc (1 Channel Driven, 1 kHz) . . . . . . . . . . . less than 0.08%
•Input sensitivity/Impedance   
AUX etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 mV/47 k-ohms
•Frequency Response / 
AUX etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 22 kHz ±3dB
•Signal to Noise ratio 
(20 kHz Factory LPF, IHF-A network, Shorted)
AUX etc (0 dB Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 dB
VIDEO SECTION / ビデオ部
•Video Signal Level / 
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p/75 ohms
Component (Y/PB, PR) . . . . . . . . . . . 1 Vp-p/0.7 Vp-p/75 ohms
Signal to Noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 dB
TUNER SECTION / チューナー部
FM Section / FM チューナー部
•Tuning Range / 
U, C,T, K, A, B, G, L, V models . . . . . . . . 87.50 to 108.00 MHz
J model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76.0 to 108.0 MHz
•Signal to Noise ratio (Mono). . . . . . . . . . . . . . 75 dB
•Sensitivity (S/N 30 dB) /  . . . . . . . . . . . . 1.0 µV
AM Section / AM チューナー部
•Tuning Range / 
U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1700 kHz
T, K, A, B, G, L, V, J models . . . . . . . . . . . . . . . 522 to 1629 kHz
•Signal to Noise ratio. . . . . . . . . . . . . . . . . . . . 32 dB
•Sensitivity (S/N 20 dB) /  . . . . . . . . . . . 700 µV
CD/DVD PLAYER SECTION（CD/DVDレシーバー部）
•Signal to Noise ratio. . . . . . . . . . . . . . . . . . . . 95 dB
•Total Harmonic Distortion /  . . . . . . . . . . 0.007%
• Separation /  . . . . . . . . . . . . . . . . . . . . . . 90 dB
AUDIO FORMAT / オーディオ部
• Dolby Digital/MPEG decode (not decode DTS) /

• PCM DATA: 16 bit
• LPCM DATA: 20/24 bit
Fs: 44.1, 48 kHz support/88.2, 96 kHz downmix support /

• MP3: 32 kbps to 320 kbps, 16 kHz to 48 kHz sampling rate /

• WMA: Up to 192 kbps (not support 32 kbps),
32 kHz, 44.1 kHz, 48 kHz sampling rate /


• Support mono and stereo WMA/MP3 andVBR files /

GENERAL / 総合
•Power Supply / 
U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz
T model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 50 Hz
K model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 60 Hz
A model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V, 50 Hz
B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz
L model . . . . . . . . . . . . . . . . . . . . . . . . AC 220–240V, 50/60 Hz
V model . . . . . . . . . . . . . . . . . . . . . . . AC 110–120 V, 50/60 Hz
J model . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 100 V, 50/60 Hz
•Power consumption /  . . . . . . . . . . . . . . . . . . . . 30 W
•Standby Power consumption / 
U, C,V, J models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9 W
T, K, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 W
A, L models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 W
•Dimensions (W x H x D) / 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 x 112.8 x 295.9 mm
(8-7/16” x 4-7/16” x 11-5/8”)
•Weight /  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.65 kg
(5 lbs. 13oz)
•Finish / 
Silver color . . . . . . . . . . . . . . . . . . . . U, K, B, G, L, V, J models
Gold color . . . . . . . . . . . . . . . . . . . . . . . U, C, T, A, G, V models
•Accessories /  . . . . . . . . . . . . . . . . . . Remoe control x 1
Battery (size “AA”, R06, UM-3) x 2
AM loop antenna x 1
Indoor FM antenna x 1
Video pin cable x 1
* Specifications subject to change without prior notice.

9
RDX-E700/NX-E700
RDX-E700
NX-E700
NX-E700
•Type /  . . . . . . . . . . . . 2-Way Bass Reflex Speaker System
Magnetic Shielding Type

•Driver / 
Woofer . . . . . . . . . . . . . . . . . . . . . .11 cm (4-1/2”) Cone Type
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . 2.5 cm (1”) DomeType
•Frequency Response / 
U, C,T, K, A, B, G, L, V models . . . .60 Hz to 28 kHz (-10dB)
J model . . . . . . . . . . . . . . . . . . . . . . .60 Hz to 28 kHz (-10dB)
60 Hz to 80 kHz (-30dB)
•Impedance /  . . . . . . . . . . . . . . . . . . . . . 6 ohms
•Nominal Input /  . . . . . . . . . . . . . . . . . . . . . . . . . 40W
•Maximum Input /  . . . . . . . . . . . . . . . . . . . . . . . 110 W
•Sensitivity /  . . . . . . . . . . . . . . .85 dB/2.83 V/m
•Clossover Frequency /  . . . . . . . 3 kHz
•InputTerminal /  . . . . . . . . . . . . . Screw/Banana Type
•Dimensions (W x H x D) / 
. . . . . . . . . . . . . . . . . . . . . . . . . . . .165 mm x 255 mm x 183 mm
(6-1/2” x 10-1/16” x 7-3/16”)
•Weight /  . . . . . . . . . . . . . . . . . . . . . . . . .3.4 kg (7 lbs 8 oz)
•Finish /  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Black
•Accessories /  . . . . . . . . . . . . . . Speaker cable (4m) x 2
* Specifications subject to change without prior notice.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
ドルビーラボラトリーズからの実施権により製造されています。
「ドルビー」及びダブルD記号は、ドルビーラボラトリーズの商標
です。
“DTS” and “DTS DIGITAL OUT” are trademarks of Digital Theater Sys-
tems, Inc.
DTSおよびDTSDigitalOutはデジタルシアターシステムズの登録
商標です。
“DivX”, “DivX Certified”, and associated logos are trademarks of
DivXNetworks, Inc and are used under license.
DivX、DivXCertifiedおよびそのロゴは DivXNetworksInc の商標
であり、ライセンス承諾を得て使用されます。
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS
and Thomson multimedia.
MPEG-1AudioLayer3音声圧縮技術は、FraunhoferIIS および
THOMSONmultimediaからライセンスを受けています。
● NX-E700● RDX-E700
104.8(4-1/8")
8
(5/16") 112.8(4-7/16") 270.9(10-11/16")
295.9(11-5/8")
215(8-7/16")
15(9/16")
10(3/8")
255(10-1/16")
165(6-1/2") 183(7-3/16")
■DIMENSIONS / 寸法図
Unit : mm (inch)

10
RDX-E700/NX-E700
RDX-E700
NX-E700
■INTERNAL VIEW / 各部名称
qAM/FM TUNER
wMAIN (2) P.C.B.
eMAIN (3) P.C.B. (J model only)
rMAIN (1) P.C.B.
tPOWER SUPPLY UNIT
yFRONT P.C.B.
uDVD MECHANISM ASS’Y
t
u
y
rq w e
■RDX-E700 DISASSEMBLY PROCEDURES/RDX-E700分解手順
 
 
1. トップカバーの外し方
a. qのネジ2本、wのネジ4本を外します。（Fig.1）
b. トップカバーを後方へスライドさせ取り外します。
（Fig.1）
2. フロントパネルユニットの外し方
a. トレーを開き、ドア飾りを外し、トレーを閉じます。
（Fig.1）
b. eのネジ4本を外します。（Fig.1）
c. コネクターCN14を外します。（Fig.2）
d. フック2箇所を外し、フロントパネルユニットを前方へ引
き出します。（Fig.2）
3. DVDメカニズムASSYの外し方
a. rのネジ4本、tのネジ1本を外します。（Fig.1）
b. コネクターCN11、CN12、及びアース線を外し、DVDメカ
ニズムASSYを取り外します。（Fig.2）
1. Removal of Top Cover
a. Remove 2 screws ( q ) and 4 screws ( w ). (Fig. 1)
b. Slide the Top Cover rearward to remove it. (Fig. 1)
2. Removal of Front Panel Unit
a. Open the tray, remove the door ornament and close the
tray. (Fig. 1)
b. Remove 4 screws ( e ). (Fig. 1)
c. Remove connectors CN14. (Fig. 2)
d. Remove 2 hooks and then slide the Front Panel Unit
forward. (Fig. 2)
3. Removal of DVD Mechanism Ass’y
a. Remove 4 screws ( r ) and a screw ( t ). (Fig. 1)
b. Remove connectors CN11, CN12 and GND wire and
then remove the DVD Mechanism Ass’y. (Fig. 2)
•Remove parts in disassembly order as numbered.
•Disconnect the power cable from the AC outlet.

11
RDX-E700/NX-E700
RDX-E700
NX-E700
Top Cover

Front Panel Unit

DVD Mechanism Ass'y

rr
e
e
t
q
q
e
w
Door Ornament

Hook


GND Wire

CN12
CN14
CN11
Hook

Fig. 1
Fig. 2
● 手動でトレーを開く方法
a. 本機を上下反転します。
b. トレーが出てくるまで、ドライバーでローディングギア
を図に示す矢印の方向に回転します。
c. トレーをそっと引き出します。
●HOWTO MANUALLY EJECTTHETRAY
a. Turn the unit bottom up.
b. Turn the Loading Gear in the direction indicated with a
screwdriver until the tray is ejected.
c. Gently pull the tray out.
Tray

Screwdriver
 Loading Gear

Tray

Fig. 3

12
RDX-E700/NX-E700
RDX-E700
NX-E700
トレーロックモードは、トレーのオープン／クローズ機能
を一時的に停止する機能です。
● トレーロックモードの起動
1. 電源オフの状態で、TIMERキーとMODEキーを
押しながらSTANDBY/ONキーを4 秒間以上押し続
けます。
2. トレーロックモードが起動し「TRADE ON」と表示し
た後、通常の表示に戻ります。
注1: トレーロックモード起動後、オープン／クローズ
キー以外の操作は通常通り行うことができます。
注2: DISCがトレー上にセットされていない場合、トレー
ロックモードは自動的に解除されます。
● トレーロックモードの解除
1. 電源オフの状態で、TIMERキーとMODEキーを
押しながらSTANDBY/ONキーを4 秒間以上押し続
けます。
2. トレーロックモードが解除され「TRADE OFF」と表示
した後、通常の表示に戻ります。
■TRAY LOCK MODE/トレーロックモード
■FACTORY RESET/ファクトリーリセット
下記の場合、DVDメカニズムASSYの仕向け地別設定を行
うためにファクトリーリセットを行います。
・ DVDメカニズムASSY(MPEGP.C.B.を含む)を交換した場合
・MPEGP.C.B.を交換した場合
・DVDファームウエアを更新した場合
● 操作方法
1. 電源オフの状態で、SOUNDキーとMODEキーを
押しながらSTANDBY/ONキーを4 秒間以上押し続
けます。
2. サービスモードが起動した後、本機に接続したTVモニ
ターの画面上にソフトウエアバージョン情報が下記のよ
うに表示されます。
＜表示例＞
・SERVICE MENU・
DivX Version : MAIN02.03.00.09
MPEG Version : RDX-E70010042
MACRO VISION : 2005.06.01
Version Setting  J 2
Push'MODE'Button4sforfactoryreset.
同時に本機の表示器にホストソフトウエアバージョンが
表示されます。
＜表示例＞
3.MODEキーを4秒間以上押し続けます。
本機の表示器が点滅を繰り返した後、自動的に電源が
OFFします。
以上の操作でファクトリーリセットは完了です。
Regioncode
050824-1
In the TRAY LOCK mode, the tray open/close function is
stopped temporarily.
●SettingTray Lock mode
1. With the power turned off, while pressing the "TIMER"
key and "MODE" key, keep pressing the "STANDBY/ON"
key for 4 seconds or longer.
2. When the Tray Lock mode is set, "TRADE ON" is dis-
played which then returns to the normal display.
NOTE 1: Even after theTray Lock mode is set, all functions
remain the same as usual except the "open/close"
key.
NOTE 2: If no disc is loaded in the tray, theTray Lock mode
is cancelled automatically.
●CancelingTray Lock mode
1. With the power turned off, while pressing the "TIMER"
key and "MODE" key, keep pressing the "STANDBY/ON"
key for 4 seconds or longer.
2. When theTray Lock mode is cancelled, "TRADE OFF" is
displayed which then returns to the normal display.
When any of the following conditions applies, perform the
factory reset procedure to make setting of the DVD Mecha-
nism Ass’y suitable for the destination region.
• The DVD Mechanism Ass’y (including MPEG P.C.B.) has
been replaced.
• MPEG P.C.B.has been replaced.
• DVD firmware has been updated.
●Operation procedure
1. With the power turned off, while pressing the "SOUND"
key and "MODE" key, keep pressing the "STANDBY/ON"
key for 4 seconds or longer.
2. When the Service Mode is set, the software version in-
formation is displayed on the TV monitor screen con-
nected to the main unit as shown below.
<Example>
At the same time, the host software version is displayed
of the main unit.
<Example>
3. Keep pressing the "MODE" key for 4 seconds or longer.
The display unit of the main unit repeats flashing and
then the power is turned off automatically.
This completes the Factory Reset procedure.
050824-1
・SERVICE MENU・
DivX Version : MAIN02.03.00.09
MPEG Version : RDX-E70010042
MACRO VISION : 2005.06.01
Version Setting  J 2
Push'MODE'Button4sforfactoryreset.
Region code

12345678
A
B
C
D
E
F13
RDX-E700/NX-E700
■PRINTED CIRCUIT BOARD
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTSWILL BE AVAILABLE)
MPEG P.C.B.
(Side B) Lead Free Solder Used
MAIN (1)
CN12
MAIN (1)
CN11
DVD MECHANISM
(SPINDOLE & SLED)
DVD MECHANISM
(OPEN/CLOSE)
MPEG P.C.B.
(Side A) Lead Free Solder Used
DVD MECHANISM (PICK-UP)

12345678
A
B
C
D
E
F14
RDX-E700/NX-E700
DIGITAL
OUT
OPTICAL
(not installed)
D1/D2
POWER SUPPLY UNIT
CN92
POWER SUPPLY UNIT
CN93
FRONT CN14
POWER SUPPLY UNIT
CN91
AM/FM TUNER
MPEG
CN35
MPEG
CN36
SPEAKERS
SUBWOOFER
OUT
AV
(B, G models)
Y
VIDEO
PB
PR
VIDEO OUT
AUX
OUT
AUX
IN
TV
IN
LR
(B, G models)
■PRINTED CIRCUIT BOARD
MAIN (1) P.C.B.
(Side A) Lead Free Solder Used
MAIN (3) P.C.B.
(Side A)
MAIN (2) P.C.B.
(Side A) Lead Free Solder Used
●J model
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)

12345678
A
B
C
D
E
F15
RDX-E700/NX-E700
■PRINTED CIRCUIT BOARD
MAIN (1) P.C.B.
(Side B) Lead Free Solder Used
MAIN (2) P.C.B.
(Side B) Lead Free Solder Used
MAIN (3) P.C.B.
(Side B) Lead Free Solder Used
●J model
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)

12345678
A
B
C
D
E
F16
RDX-E700/NX-E700
■PRINTED CIRCUIT BOARD Lead Free Solder Used
POWER CABLE
MAIN (1)
CN93
MAIN (1)
CN92
MAIN (1)
CN91
POWER SUPPLY UNIT
(Side A)
FRONT P.C.B.
(Side A)
MAIN (1) CN14
VOLUME
MODE
SOUND
DISPLAY
TIMER
PHONES
STANDBY/ON
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)

12345678
A
B
C
D
E
F17
RDX-E700/NX-E700
■BLOCK DIAGRAM
1
2
3
4
AMP PART
FILTER
L/C
BUFFER
OPAMP
ADC
U-COM CONTROL 12
IC81
2,3
6
48,1
42,43
44,45
46,47
5 4 7
13
IC82
IC14
VR21 VR22
14 7
9
4
12
2,3
10,11
5,6
IC83
M2068MD
FILTER
OPAMP
AM AM/FM
TUNER
FM
REC OUT
TUNER IN
AUX IN
TV IN
DVD IN
SCART IN
H/P OUT
SUB_PREOUT
WM8776
26, 27
DAC
DOUT
SDATA3
OUT
SD3
OUT
FILTER
VIDEO
CVBS
OUT
FILTER
VIDEO
27MHz
OSC
SDRAM64Mbit
IC32
16M
FLASH MEMORY
IC31
RF SERVO
ZR36707
IC43
MOTOR DRIVE
AM5888S
Traverse unit
DVD MECHANISM ASS'Y
Pick-up
(HD62)
DV-342FN
IC42
EEPROM
VIDEO
BUFFER
BUFFER
OPAMP
VIDEO
SW
P15V330S
Pr
Pb
CVBS OUT
1, 3
AUDIO
AUDIO
AUDIO OUT
AUDIO IN
RGB OUT
YRGB
YUV
CVBS OUT
YUV
IC74
YUV
OUT
110
H/P
AMP
IC62
NJM4556AL
IC63
M2068MD
FILTER
L/C
FILTER
AUDIO
EQ
1A
1B
2A
2B
L+
L–
R+
R–
L+
L-CHR-CH
RELAY
RY51
IC52
IC51
RELAY
L–
R+
R–
3A
3B
PWDN
3.3V
MPEG_LRCK MPEG_BICK MPEG_MCLK
H/P OUTAUX INAUX OUT TV IN
OPTICAL
OUT
J model
only
(D1/D2) COMPONENT SUBWOOFER
PREOUT
B,G models only
SCART OUT
SDATA
AMP VCC
+VKK
+FL
–FL
FUN –12V
FUN +12V
AMP VCC
–FL
+VKK
+FL
STBY 5.6V
PWR ON
FL ON
DVD 5V
MD 5.2V
100V250V
SCLK
MIX
APO_LRCK
APO_BICK
APO_MCLK
APO_LRCK
APO_BICK
APO_MCLK
MPEG_LRCK
MPEG
SD3 OUT
WM8776
SD OUT
MPEG_BICK
MPEG_MCLK APO_SDATA
74LVC157
SW157
VOLUME
&
LIMITER
DDX
PROCE-
SSING
CROSS
OVER
IC21
IR REMOTO
FIP1
QUAD
HALF-BRIDGE
POWERSTAGE
HEAD PHONE
DOWN MIXOUT
CONTROLLER
DDX-2001 DIGITAL
AMP
DDX-2102
POWER SUPPLY UNIT
VFD DISPLAY+VFD DRIVER
(DOT MATRIX VFD)
IC33
IC73
IC71
M2068MD
BUFFER
OPAMP
IC72
M2068MD
MPEG
ZR36778
SUB PRE OUT
74VHC04
KEY SW21-29
VOLUME
JOG
Microprocessor
ST92F124VT1

12345678
A
B
C
D
E
F18
RDX-E700/NX-E700
TO DVD MECHANISM ASS'Y
TO MAIN 1/2 CN12
Page 20 B-7
TO DVD
MECHANISM ASS'Y
TO DVD
MECHANISM ASS'Y
■SCHEMATIC DIAGRAM (MPEG 1/2 (FRONT END))
* Components having special characteristics are marked Z and
must be replaced with parts having specifications equal to
those originally installed.
* Schematic diagram is subject to change without notice.
*Z印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
パーツリストに記載されている部品を使用してください。
* 本回路図は、標準回路図です。改良のため予告なく変更することがございます。
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)

12345678
A
B
C
D
E
F19
RDX-E700/NX-E700
TO MAIN 1/2 CN11
Page 20 E-3
UNCONNECTED
■SCHEMATIC DIAGRAM (MPEG 2/2 (BACK END))
* Components having special characteristics are marked Z and
must be replaced with parts having specifications equal to
those originally installed.
* Schematic diagram is subject to change without notice.
*Z印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
パーツリストに記載されている部品を使用してください。
* 本回路図は、標準回路図です。改良のため予告なく変更することがございます。
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)

12345678
A
B
C
D
E
F20
RDX-E700/NX-E700
■SCHEMATIC DIAGRAM (MAIN 1/2 (Microprocessor))
TO MPEG 1/2 CN36
Page 18 B-7
TO FRONT CN14
Page 22 B-1
TO POWER CN92
Page 23 B-7
TO POWER CN93
Page 23 D-7
TO MPEG BACK END CN35
Page 19 A-8
TO AM/FM TUNER
ST92F124V1
FLASH
Mircroprocessor
MAIN (2) MAIN (1)
MAIN (3)
* Components having special characteristics are marked Z
and must be replaced with parts having specifications equal
to those originally installed.
* Schematic diagram is subject to change without notice.
*Z印のある部品は、安全性確保部品を示しています。部品の交換が必要な場
合、パーツリストに記載されている部品を使用してください。
* 本回路図は、標準回路図です。改良のため予告なく変更することがございま
す。
FOR INFORMATION ONLY (NO REPLACEMENT COMPONENT PARTS WILL BE AVAILABLE)