YeeSite 36LEDs User manual

User Manual
36LEDs Par Light

-1-
1.BEFORE YOU BEGIN
What Is Included
1 x 36LEDs Par Light
2 x Remote Controls
1 x User Manual
1 x Holder
Unpacking Instructions
Thank you for purchasing the 36LEDs Par Light by YeeSite.
Every 36LEDs Par Light has been thoroughly tested and has been
shipped in perfect operating condition. Carefully unpack the
product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories)
appear damaged from shipping, or show signs of mishandling,
notify the carrier immediately and contact Amazon customer
support for replacement. Amazon customer support team will
definitely help you with this. You may contact Amazon customer
support team at:
https://www.amazon.com/gp/help/customer/contact-us
For urgent issue, you can call Amazon customer service as well:
U.S. and Canada: 1-866-216-1072
If no response from Amazon, you can get support directly from
YeeSite Customer Service at [e-mail]
Disclaimer
YeeSite believes that the information contained in this manual is
accurate in all respects. However, YeeSite assumes no
responsibility and specifically disclaims any and all liability to any

-2-
party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such errors or omissions
result from negligence,accident or any other cause. YeeSite
reserves the right to revise the content of this document without
any obligation to notify any person or company of such
revision,however, Yeesite has no obligation to make, and does not
commit to make, any such revisions.
Safety Notes
Please read the following Safety Notes carefully before working
with the product. The notes include important safety information
about installation, usage, and maintenance.
Always connect the product to a grounded circuit to avoid the risk
of electrocution.
Always disconnect the product from the power source before
cleaning or replacing the fuse.
Avoid direct eye exposure to the light source while the product
is on.
Make sure the power cord is not crimped or damaged.
Never disconnect the product from power cord by pulling or
tugging on the cord.
If mounting the product overhead, always secure to a fastening
device using a safety cable.
Make sure there are no flammable materials close to the product
when operating.
Do not touch the product’s housing when operating because it
may be very hot.
This product is not intended for permanent installation.
Always make sure that the voltage of the outlet to which you are
connecting the product is within the range stated on the decal or
rear panel of the product.

-3-
The product is for indoor use only! (IP20) To prevent risk of fire or
shock, do not expose the product to rain or moisture.
Always install the product in a location with adequate ventilation,
at least 20 in (50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are
blocked.
Never connect the product to a dimmer.
Never carry the product from the power cord or any moving part.
Always use the hanging/mounting bracket.
The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not
operate the product at higher temperatures.
In the event of a serious operating problem, stop using the
product immediately.
Never try to repair the product. Repairs carried out by unskilled
people can lead to damage or malfunction.
To eliminate unnecessary wear and improve its lifespan, during
periods of non-use completely disconnect the product from power
via breaker or by unplugging it. Keep this User Manual for future
use. If you sell the product to someone else, be sure that they also
receive this document.

-4-
3.9in
100mm
7.1in
180mm
2. INTRODUCTION
Product Overview
DMX I N DMX O UT
POW ER
MEN U UP DOWN E NTER
Microphone
Power
Display
Menu Button
DMX In/Out
Fan
Lenses
IR Sensor
7.1in
180mm

-5-
3. SETUP
AC Power
The 36LEDs Par Light has an auto-ranging power supply and it
can work with an input voltage range of 110 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker,
power outlet, and wiring), use the current value listed on the label
affixed to the product’s back panel, or refer to the product’s
specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker
or fuse). Make sure the product has an appropriate electrical
ground to avoid the risk of electrocution or fire.
To eliminate unnecessary wear and improve its lifespan, during
periods of non-use completely disconnect the product from
power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or
dimmer circuit, even if the rheostat or dimmer channel serves
only as a 0 to 100% switch.
Mounting
Before mounting the product, read and follow the safety
recommendations indicated in the Safety Notes.
Orientation
The 36LEDs Par Light may be mounted in any position; however,
make sure adequate ventilation is provided around the product.
Rigging
Before deciding on a location for the product, always make sure
there is easy access to the product for maintenance and
programming purposes.

Make sure that the structure onto which you are mounting the
product can support the product’s weight. See the Technical
Specifications for weight information.
When mounting the product overhead, always use a safety cable.
Mount the product securely to a rigging point, whether an
elevated platform or a truss.
When rigging the product onto a truss, use a mounting clamp of
appropriate weight capacity.
The bracket adjustment knobs allow for directional adjustment
when aiming the product to the desired angle. Only loosen or
tighten the bracket knobs manually. Using tools could damage
the knobs.
-6-
Mounting Clamps
Bracket
Adjustment Knobs x 2
Double-
Bracketed Yoke
(Not included)
Mounting Diagram

4. OPERATION
Control Panel Operation
To access the control panel functions, use the four buttons located
underneath the display. Please refer to the Product Overview to
see the button locations on the control panel.
Button Function
<MENU> Press to find an operation mode or to back out of the
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower
value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Main Level Programming Levels Description
A001 A001-511 7 channel DMX mode
D001 D001-511 4 channel DMX mode
Cf01 Cf01-99 Fade mode1 (slower)
Cj01 Cj01-99 Hopping mode
Cp01 Cp01-99 Fade mode2 (faster)
Ct01 Ct01-99 Strobe mode
RGB
r000-255(red) Custom static colors
Color combination
g000-255(green)
b000-255(blue
SLAV Slave mode
DENO Auto mode
SOUD Sound active
-7-
current menu option

DMX Linking
The 36LEDs Par Light works with a DMX controller.
Configuration(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2.Connect a DMX cable from the DMX output of the DMX controller
to the DMX input socket on the product.
DMX Personality and Starting Address
When selecting a starting DMX address, always consider the
number of DMX channels the selected DMX mode uses. If you
choose a starting address that is too high, you could restrict the
access to some of the product’s channels.
The 36LEDs Par Light uses 4 DMX channels or 7 DMX channels
and defines the highest configurable address to 511
To select the starting address, do the following:
1.Press <MENU> repeatedly until A001 or D001 shows on the
display.
2.Press <ENTER> and A001 –A511 or D001-D511 will show on
the display.
3.Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
-8-

Configuration(Standalone)
Set the product in one of the standalone modes to control without a
DMX controller. Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode
to a DMX string connected to a DMX controller. Products in
standalone mode may transmit DMX signals that could interfere
with the DMX signals from the controller.
Automatic Programs
To run the 36LEDs Par Light in automatic mode, follow the
instructions below:
-9-
7 CH
CH CH Value Function Description
CH1 0-255 Master-Dimmer
CH2 0-255 Red-Dimmer
CH3 0-255 Green-Dimmer
CH4 0-255 Blue-Dimmer
CH5 0-255 RGB
CH6 1-255 Strobe Speed
CH7 1-255 Mode
4 -C H
CH CH Value Function Description
CH1 0-255 Master-Dimmer
CH2 0-255 Red-Dimmer
CH3 0-255 Green-Dimmer
CH4 0-255 Blue-Dimmer
DMX Channel Assignments and Values

1.Press <MENU> repeatedly until DENO shows on the display.
2.Press <ENTER>.
Sound-Active Mode
To run the 36LEDs Par Light in sound-active mode, do the following:
1.Press <MENU> repeatedly until SOUD shows on the display.
2.Press <ENTER>.
Custom Color Mixing
To custom mix a static color, follow the instructions below:
1.Press <MENU> repeatedly until RGB shows on the display.
2.Press <ENTER> and one of the following will show on the display:
r_ _ _ (red)
g_ _ _ (green)
b_ _ _ (blue)
3.Press <ENTER> to cycle through the color settings.
4.When the desired color shows on the display, use <UP> or
<DOWN> to increase or decrease the color value.
5.Repeat steps 3 and 4 until the product outputs as desired.
For example, to get red color, set r255,g000,b000.
Fade mode 1 ( slower)
To run the color fading mode 1, do the following:
1.Press <MENU> repeatedly until Cf01 shows on the display.
2.Press <ENTER>.
3.Use <UP> and <DOWN> to increase or decrease the program
speed(Cf01-Cf99)
4.Press <ENTER>.
-10-

Fade mode 2 ( faster)
To run the color fading mode 2, do the following:
1.Press <MENU> repeatedly until Cp01 shows on the display.
2.Press <ENTER>.
3.Use <UP> and <DOWN> to increase or decrease the program
speed(Cp01-Cp99)
4.Press <ENTER>.
Hopping mode
To run the hopping mode, do the following:
1.Press <MENU> repeatedly until Cj01 shows on the display.
2.Press <ENTER>.
3.Use <UP> and <DOWN> to increase or decrease the program
speed(Cj01-Cj99)
4.Press <ENTER>.
Strobe mode
To run the strobe mode on 36LEDs Par Light, follow the
instructions below:
1.Press <MENU> repeatedly until Ct01 shows on the display.
2. Press <ENTER>.
3.Use <UP> and <DOWN> to increase or decrease the program
speed(Ct01-Ct99)
4.Press <ENTER>.
Master/Slave Mode (wired)
The Master/Slave mode allows a single 36LEDs Par Light product
(the “master”) to control the actions of one or more 36LEDs Par
Light products (the “slaves”) without the need of a DMX controller.
The master product will be set to operate in any Stand-Alone
mode, while the slave products will be set to operate in Slave
-11-

mode. Once set and connected, the slave products will operate in
unison with the master product.
Configure the products as indicated below.
Slave products:
1.Press <MENU> repeatedly until SLAV shows on the display.
2.Press <ENTER> to accept.
3.Connect the DMX input of the first slave product to the DMX
output of the master product.
5.Connect the DMX input of the subsequent slave products to the
DMX output of the previous slave product.
6.Finish setting and connecting all the slave products.
Master product:
1.Set the master product to operate in any Stand-Alone mode.
2.Make the master product the first product in the DMX daisy chain.
Configure all the slave products before connecting the master to
the daisy chain.
Never connect a DMX controller to a DMX string configured for
Master/Slave operation because the controller may interfere with
the signals from the master.
Do not connect more than 30 slaves to the master.
-12-
DMX I N DMX O UT
POW ER
MEN U UP DOWN E NTER
DMX IN
DMX OUT
DMX IN
DMX OUT
Master P ductroSlave P duct 1ro
Slave P duct 2ro
Additional
Products

Remote Control
ROSEO
1
3
4
7
8
6
5
Auto mode
Hopping mode
Sound-active mode
Red color
Green color
Fade 1, Fade 2
Strobe mode
11
14
13
12
Cyan color
Amber color
Power ON/OFF
Speed - Speed +
Roseo color
White color
Blue color
DMX mode
10
9
15 16
2
Icon Button Function Display on Panel
1 ON/OFF
2 DMX Mode A001/D001/
SLAV
3 Auto Mode DENO
4 Hopping Mode CJ**
5 Fade 1, Fade 2 CF**/CP**
6 Strobe Mode CT**
7 Sound-Active
Mode SOUD
8 Red Color r255
9 Green Color g255
10 Blue Color b255
11 Roseo Color
12 Amber Color
13 Cyan Color
14 White Color
P32
15 Speed-
16 Speed+
Function Description
Press this button to turn on or
turn off the light
Repeat e d l y p r e s s t h i s b u t t o n to
switch betwe e n A0 0 1 / D 001/SLAV
Press this button to run auto mode
Press +/- to adjust hopping speed
Press +/- to adjust fade speed
Press +/- to adjust strobe rate
Press this button to run
sound-active mode
Press this button for Red color
Press this button for Green color
Press this button for Blue color
Press this button for Rose color
Press this button for Amber color
Press this button for Cyan color
Press this button for White color
Decrease the speed of a program
Increase the speed of a program
-13-
AMBER
A32
C32
U32

5. MAINTENANCE
Product Maintenance
Dust build-up reduces light output performance and can cause
overheating. This can lead to reduction of the light source’s life
and/or mechanical wear. To maintain optimum performance and
minimize wear, clean your lighting products at least twice a month.
However, be aware that usage and environmental conditions could
be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1.Unplug the product from power.
2.Wait until the product is at room temperature.
3.Use a vacuum (or dry compressed air) and a soft brush to
remove dust collected on the external surface/vents.
4.Clean all transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
5.Apply the solution directly to a soft, lint free cotton cloth or a
lens cleaning tissue.
6.Softly drag any dirt or grime to the outside of the transparent
surface.
7.Gently polish the transparent surfaces until they are free of
haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
6.TECHNICAL SPECIFICATIONS
Material: Plastics + Metal panel
Item size: 6.9 x6.9 x3.9in
Input Voltage: 110-240VAC
Power: 40-watts (included 36-watts led + 4-watts Power)
Light Source: 36x1-watt LED(12Red+12Green+12Blue)
Net Weight: 0.6Kg
-14-