YellaWood Adirondack Chair User manual

Adirondack Chair
1
GET MORE PROJECT PLANS AT BuildYella.com
Cutting parts: 1 – 2 hours
Assembly: 1 – 2 hours
Finishing: 2 hours
Total: 4 – 6 hours
BUILD TIME
There are many variations of the classic adirondack
chair. This particular version features straightforward
construction and common materials.
This chair makes for a satisfying project that can
be built and finished in one weekend. And when
properly finished, it will provide years of
comfortable seating.

Adirondack Chair
2
GET MORE PROJECT PLANS AT BuildYella.com
A(2) ¾ x 7 ¼ x 36
B(2) 1 ½ x 3 ½ x 21 ½
C(6) ¾ x 3 x 23
D(1) ¾ x 6 x 36
E(2) ¾ x 3 x 34
F(2) ¾ x 3 x 32
G(2) ¾ x 3 x 17
H(2) 1 ½ x 3 ½ x 21
I(2) ¾ x 7 ¼ x 30
J(1) 1 ½ x 3 ½ x 26
K(2) ¾ x 2 x 5
CUT LIST
Miter saw (or hand or circular saw)
Table saw
Jig saw (or hand or circular saw)
Drill/driver
1/8” drill bit
Clamps
Damp rag to wipe up excess glue
SUPPLIES
TOOLS
(4) 1 x 4 x 8’
(2) 1 x 8 x 8’
(1) 2 x 4 x 10’
1 ¼” deck screws
2” deck screws
3” deck screws
Waterproof wood glue
A
B
C
D
E
F
X 2
X 2
X 6
X 1
X 2
G
H
X 2
X 2
X 2
I
J
K
X 2
X 1
X 2

Adirondack Chair
3
GET MORE PROJECT PLANS AT BuildYella.com
Braces
F
E
D
G
I
I
J
AB
B
C
H
H
A
K
K
5”
2”
45
I
90 A
Arm detail
(Save this
cutout to make
piece K)
Back leg detail
1 1/2”
4” 3” (J) (H)
(K)
2 1/2”
1 1/2”
1 1/2”
3” (B) (B)
15”
15”
19”
8”
2 1/2”
2 3/4”

Adirondack Chair
4
GET MORE PROJECT PLANS AT BuildYella.com
BUILDING STEPS
01 Cut the back legs (A) to length and lay out and
cut the angles according to the detail drawing.
Use a jig saw or circular saw and guide to make
smooth, straight cuts. Note which cutout pieces
you will be saving to make braces later on. Lay
out where seat stretchers (B) will be attached
according to detail drawing. Drill pilot holes.
02 Cut seat stretchers (B) to length and attach to back
legs according to layout marks with 2” screws.
03 Cut arms (I) to length and mark where back
support (J), front legs (H) and braces (K) will be
attached according to detail drawing. Drill 1/8”
pilot holes.
04 Clamp back support (J) in place and attach with
2” deck screws. Trim two of the cutout pieces
from back legs to make braces (K) according to
detail drawing, and attach them and front legs (H)
to the underside of the arms where noted with 3”
deck screws.
05 Measure up from the bottom of both front legs
and mark 16”. Clamp back leg/stretcher assembly
to the front leg arm assembly, keeping the top of
the back legs at the 16” mark and the front edge
of the back legs flush with the front edge of the
front legs. Attach with 2” deck screws.

Adirondack Chair
5
GET MORE PROJECT PLANS AT BuildYella.com
06 Cut all other pieces to lengths according to cut list.
Lay out your back slats (D, E, & F) with the best sides
facing down and ¼” spacers between each slat.
Use a straight edge along the bottoms to help with
alignment. Drill pilot holes in back stretchers (G) and
attach to the back of the slats. Attach bottom edge of
the bottom stretcher 4” up from bottom of slats, and
the second stretcher 16” up from that.
07 Set back slat assembly into place, with the bottom
stretcher (G) resting on the back seat stretcher (B).
With 2” screws attach through the slats (D, E, & F)
into the seat stretcher (B) and back support (J).
08 Drill pilot holes in seat slats (C) and lay them out
on the seat with ¼” spacers between each slat.
Remove one arm assembly for drill clearance
and drill pilot holes into the back legs through
your slat pilot holes, then attach with 2” screws.
Reattach arm assembly and repeat for other side.
BUILDING STEPS
09 Break all edges and sand all surfaces smooth
before applying waterproof finish according to
manufacturer instructions.

6
GET MORE PROJECT PLANS AT BuildYella.com
FASTENER AND HARDWARE
INFORMATION SHEET
For interior or exterior applications
Use fasteners and hardware that are in
compliance with the manufacturer’s
recommendations and the building codes for
their intended use. As with any good design and
construction practices, treated wood should not
be used in applications where trapped moisture
or water can occur. Where design and/or actual
conditions allow for constant, repetitive or long
periods of wet conditions, only stainless steel
fasteners should be used.
For exterior applications
The following minimum galvanization levels may
be used for connectors, joist hangers,
fasteners and other hardware that are placed in
direct contact with exterior applications of
micronized copper treated wood:
• Fasteners - nails, screws, etc.
ASTM – A 153 (1 oz/ft²)
• Hardware - connectors, joist hangers, etc.
ASTM – A 653 G90 (0.90 oz/ft²)
The effects of other building materials within a
given assembly, along with environmental factors,
should also be considered when selecting the
appropriate hardware and fasteners to use for a
given project containing treated wood.
Stainless Steel fasteners and hardware are
required for Permanent Wood Foundations below
grade and are recommended for use with treated
wood in other severe exterior applications such as
swimming pools, salt water exposure, etc. - Type
304 and 316 are recommended grades to use.
Aluminum building products may be placed in
direct contact with YellaWood®brand products
used for interior uses and above ground exterior
applications such as decks, fencing, and
landscaping projects. Examples of aluminum
products include siding, roofing, gutters, door and
window trim, flashing, nails, fasteners and other
hardware connectors. However, direct contact of
treated products and aluminum building products
should be limited to code-compliant construction
applications that provide proper water drainage
and do not allow the wood to be exposed to
standing water or water immersion.
We recommend you contact the aluminum
building products manufacturer for its
recommendations regarding use of its aluminum
products in contact with treated wood in ground
contact applications or when exposed to salt
water, brackish water, or chlorinated water, such as
swimming pools or hot tubs.
Also check with the aluminum building products
manufacturer regarding compatibility with other
chemicals and cleaning agents and the use of their
aluminum products in commercial, industrial, and
specialty applications such as boat construction.
YellaWood®brand pressure treated products
are treated with copper and other preservatives
(the “Preservatives”) and preservative methods,
systems, and technologies of unrelated third
parties. For details regarding the Preservatives,
methods, systems, and technologies used by
Great Southern Wood Preserving, Incorporated,
see http://www.greatsouthernwood.com/products/
yellawood or write us at P.O. Box 610, Abbeville,
AL 36310. Ask dealer for warranty details or visit
http://www.greatsouthernwood.com/products/
warranties. For important handling and other
information concerning our products or for a
copy of the YellaWood®brand Safety Data Sheet
(SDS), please visit us at www.greatsouthernwood.
com or write us at P.O. Box 610, Abbeville, AL
36310. YellaWood®and the yellow tag are federally
registered trademarks of Great Southern Wood
Preserving, Incorporated.
Great Southern Wood Preserving, Incorporated
makes no warranties expressed or implied as to the
fitness for a particular purpose of this plan.

7
GET MORE PROJECT PLANS AT BuildYella.com
IMPORTANT INFORMATION
• Consult the end tag to determine which
preservative or preservative system was used
in the treatment of that particular product.
YellaWood®brand products may be used in
direct contact with aluminum building products
when limited to code-compliant construction
applications that provide proper water drainage
and do not allow the wood to be exposed to
standing water or water immersion.
• Use fasteners and other hardware that
are in compliance with building codes
for the intended use.
• Do not burn preserved wood.
• Wear a dust mask and goggles when cutting or
sanding wood.
• Wear gloves when working with wood.
• Some preservative may migrate from the treated
wood into soil/water or may dislodge from the
treated wood surface upon contact with skin.
• Wash exposed skin areas thoroughly.
• All sawdust and construction debris should be
cleaned up and disposed of after construction.
• Wash work clothes separately from other
household clothing before reuse.
• Preserved wood should not be used where it may
come into direct or indirect contact with drinking
water, except for uses involving incidental contact
such as fresh water docks and bridges.
• Do not use preserved wood under circumstances
when the preservative may become a component
of food, animal feed or beehives.
• Do not use preserved wood as mulch.
• Only preserved wood that is visibly clean and
free of surface residue should be used.
• If the wood is to be used in an interior application
and becomes wet during construction, it should
be allowed to dry before being covered or
enclosed.
• If you desire to apply a paint, stain, clear water
repellent or other finish to your preservative-
treated wood, we recommend following
the manufacturer’s instructions and label of
the finishing product. Before you start, we
recommend you apply the finishing product to
a small exposed test area before finishing the
entire project to ensure it provides the intended
result before proceeding.
• Mold growth can and does occur on the surface
of many products, including untreated and
treated wood, during prolonged surface exposure
to excessive moisture conditions. To remove
mold from the treated wood surface, wood
should be allowed to dry. Typically, mild soap and
water can be used to remove remaining surface
mold. For more information visit www.epa.gov.
• Projects should be designed and installed in
accordance with federal, state and local building
codes and ordinances governing construction in
your area, and in accordance with the National
Design Specifications (NDS) and the Wood
Handbook.
Disposal Recommendations:
Preserved wood may be disposed of
in landfills or burned in commercial
or industrial incinerators or boilers
in accordance with federal, state and
local regulations.

Get more project plans at BuildYella.com
Adirondack Chair // Hack
PROJECT PLAN
guests, this Hack project allows for one
of the arms to feature a cup holder for
carefree beverage consumption.
The plan calls for a simple cut out as well
as a small structure underneath to support
cups up to 3" in diameter. It's one of the
simplest plans in the YellaWood®project
plan library, giving little reason not to give
this one a go.
$$$
Build an easy add-on to your
Adirondack chair.
The Adirondack chair is classic for a
number of reasons. Its ergonomic,
lounge-ready design, its inviting wide
arms, and its endless varieties of detailing
make it an American staple. At more than
100 years old, the chair has survived the
test of time and is a beloved beacon of
backyard rest.
Even with all its history, this masterpiece
could use one small upgrade. Instead
of risking a drink spilling on you or your
BUILD TIME
DIFFICULTY
COST
$$
1
HR
Note:
The previous version did not call for arms long enough to accommodate the hack. This plan was updated in Summer 2015,
so be sure to check buildyella.com for the most current plans before printing the instructions.
8

TOP
OVERALL SIZE
50"
43 "
3
/
8
34 "
3/8
9

SEQUENCE OF
BUILD
OVERVIEW OF STEPS
3: FINISHING
BUILD TIME
½ ½1 2 5
++=
CUTTING ASSEM B LY FINISHING TOTAL IN JUST
HRS HRS HRS HRS
1: HOLE CUT-OUT 2: SUPPORT
STEPS
10

Notes:
Consider using YellaWood®KDAT and higher grade products
to achieve more professional results.
1x 1x2x8' YellaWood®brand
pressure-treated pine
158" wood screws + appropriate bit
Preferred wood nish
WHAT YOU’LL NEED
½LB BOX
HARDWARE
WOOD FINISHING
MATERIALS
TOOLS
Miter saw
(or chop saw)
Drill / driver
Measuring
tape
Radial sander
(or sanding block)
Pencil
Waterproof
wood glue
(optional)
Damp cloth
(optional)
Combination
countersink bit
(with 2" long 18" bit)
Work gloves
Dust mask
Safety glasses
Ear protection
SAFETY EQUIPMENT
3 14"Hole saw
11

INSTRUCTIONS
FOR ALL SECTIONS
A S S E M B LY
CONGRATULATIONS. ENJOY YOUR NEW UPGRADED ADIRONDACK CHAIR!
1
4 5
3
2
Choose which arm you would like the cup
holder to be placed on.
Center the cup holder support
underneath the hole as shown and
attach from above using two 1 58"
screws per joint.
Measure 3" from the front edge of the
arm equidistant from both sides. Mark a
center point and carefully cut out the hole
using a 3 14"hole-saw.
Ease any sharp edges using a radial
sander or sanding block with medium grit.
Apply preferred finish to the wood.
Cut two pieces out of the 1x2 stock at
4 14"long and one piece to 2 34". Create
a C-shape assembly with these pieces.
Use a square to maintain a 90º angle.
12

GALLERY OF IMAGES
13

FASTENER & HARDWARE INFORMATION
FOR INTERIOR OR EXTERIOR APPLICATIONS
Use fasteners and hardware that are in compliance with the manufacturer’s
recommendations and the building codes for their intended use. As with any good
design and construction practices, treated wood should not be used in applications
where trapped moisture or water can occur. Where design and/or actual conditions
allow for constant, repetitive or long periods of wet conditions, only stainless steel
fasteners should be used.
FOR EXTERIOR APPLICATIONS
The following minimum galvanization levels may be used for connectors, joist
hangers, fasteners and other hardware that are placed in direct contact with exterior
applications of micronized copper treated wood:
• Fasteners – nails, screws, etc. ASTM – A 153 (1 oz/ft²)
• Hardware – connectors, joist hangers, etc. ASTM – A 653 G90 (0.90 oz/ft²)
The effects of other building materials within a given assembly, along with
environmental factors, should also be considered when selecting the appropriate
hardware and fasteners to use for a given project containing treated wood.
Stainless Steel fasteners and hardware are required for Permanent Wood Foundations
below grade and are recommended for use with treated wood in other severe exterior
applications such as swimming pools, salt water exposure, etc. Type 304 and 316 are
recommended grades to use.
ALUMINUM
Aluminum building products may be placed in direct contact with YellaWood® brand
products used for interior uses and above ground exterior applications such as decks,
fencing, and landscaping projects. Examples of aluminum products include siding,
roofing, gutters, door and window trim, flashing, nails, fasteners and other hardware
connectors. However, direct contact of treated products and aluminum building
products should be limited to code-compliant construction applications that provide
proper water drainage and do not allow the wood to be exposed to standing water or
water immersion.
We recommend you contact the aluminum building products manufacturer for its
recommendations regarding use of its aluminum products in contact with treated
wood in ground contact applications or when exposed to salt water, brackish water, or
chlorinated water, such as swimming pools or hot tubs.
Also check with the aluminum building products manufacturer regarding compatibility
with other chemicals and cleaning agents and the use of their aluminum products in
commercial, industrial, and specialty applications such as boat construction.
YellaWood®brand pressure treated
products are treated with preservatives
(the “Preservatives”) and preservative
methods, systems, and technologies
of unrelated third parties. For details
regarding the Preservatives, methods,
systems, and technologies used by
Great Southern Wood Preserving,
Incorporated, see www.yellawood.
com/preservative or write us at
P.O. Box 610, Abbeville, AL 36310.
Ask dealer for warranty details. For
warranty or for important handling
and other information concerning our
products including the appropriate
Safety Data Sheet (SDS), please visit
us at www.yellawood.com/warranties
or write us at P.O. Box 610, Abbeville,
AL 36310. YellaWood® and the yellow
tag are federally registered trademarks
of Great Southern Wood Preserving,
Incorporated.
Great Southern Wood Preserving,
Incorporated makes no warranties
expressed or implied as to the fitness
for a particular purpose of this plan.
14

IMPORTANT INFORMATION
• Consult the end tag to determine which preservative or preservative system was
used in the treatment of that particular product. YellaWood®brand products may
be used in direct contact with aluminum building products when limited to code-
compliant construction applications that provide proper water drainage and do not
allow the wood to be exposed to standing water or water immersion.
• Use fasteners and other hardware that are in compliance with building codes for
the intended use.
• Do not burn preserved wood.
• Wear a dust mask and goggles when cutting or sanding wood.
• Wear gloves when working with wood.
• Some preservative may migrate from the treated wood into soil/water or may
dislodge from the treated wood surface upon contact with skin.
• Wash exposed skin areas thoroughly.
• All sawdust and construction debris should be cleaned up and disposed of after
construction.
• Wash work clothes separately from other household clothing before reuse.
• Preserved wood should not be used where it may come into direct or indirect
contact with drinking water, except for uses involving incidental contact such as
fresh water docks and bridges.
• Do not use preserved wood under circumstances when the preservative may
become a component of food, animal feed or beehives.
• Do not use preserved wood as mulch.
• Only preserved wood that is visibly clean and free of surface residue should be
used. If the wood is to be used in an interior application and becomes wet during
construction, it should be allowed to dry before being covered or enclosed.
• Mold growth can and does occur on the surface of many products, including
untreated and treated wood, during prolonged surface exposure to excessive
moisture conditions. To remove mold from the treated wood surface, wood should
be allowed to dry. Typically, mild soap and water can be used to remove remaining
surface mold. For more information visit www.epa.gov.
• Projects should be designed and installed in accordance with federal, state
and local building codes and ordinances governing construction in your area,
and in accordance with the National Design Specifications (NDS) and the Wood
Handbook.
DISPOSAL
RECOMMENDATIONS
Preserved wood may be disposed of
in landfills or burned in commercial
or industrial incinerators or boilers in
accordance with federal, state and local
regulations.
15