YELLOWRIVER YR-W0384T User manual

84*3W RGB TRI LED Wall Wash Light
Model:YD
YR-W0384T

Contents
Section 1.Getting Started
Unpacking
Safety Instruction
Section 2. Set Up
Installation
Controlling Board
Machine Connection
Section 3. troubleshooting
Troubleshooting
Section 4. Reference
Control Menu
DMX Protocol
Dimmer Curve
Specification
Section 1.Getting Started
Unpacking
Safety Instruction

Unpacking
1pc Fixture
1pc User Manual
Thanks for choosing our LED WALL WASH serial products. Carefully unpack the
box and check the contents to ensure that all parts are present and in good conditions. If
anything damaged in transit, notify the shipper immediately and keep the packing material
for inspection. Again, please save the carton and all packing materials. If a fixture must be
returned to manufacturer, it is important that the fixture be returned in the original
manufacturer box and packing.
Safety Instruction
Please conserve this manual as operation guidance. If you sell this product to other
user, please make sure that they also receive this user manual.
Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on the decal or rear panel of
the fixture.
If the fixture is intended to indoor use only. To prevent risk of fire or shock, do not
expose fixture to rain or moisture. Make sure there are no flammable, explosive or
corrosive materials surrounded in 10meters while operating.
The unit must be installed in a location with adequate ventilation, at least 5m away from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Some fixture may carry high heat, do not aim at objective more than 2minutes.
Safe rope should be used to install machine. Bearing of safe rope should be more than
3times of the machine weight. Complimentary signal cable transmits signals to 20 unit
fixtures at most. Signal amplifier is a must to connect more fixtures. And a terminal
should be added at the end of last fixtures’ DMX sockets, 120 Ohm, 1/4W resistance
need welding between Pin 2 and Pin3.
For your safe, please read this user manual carefully before turn on
the fixture. This machine should be operated by qualified engineer！

Always disconnect from the power source before servicing or replacing fuse/lamp and
be sure to replace with same fuse/lamp size and type. Cut off power before moving,
repairing and cleaning the machine.
To avoid electric shock, all fixtures must be connected to circuits with a suitable earth
connection.
Always secure fixture using a safety chain and carrying handles.
Do not operate at ambient temperatures higher than 104℉(40℃).
The power cable for this fixture is 1 m ㎡ ， please mind the safety requirements in
actual using, if any wrong operation, our company takes no responsibility for any loss.
Also, make sure the power cord is never crimped or damaged.
In case of failure or mis-function occurred, stop using immediately. Never try to repair
the fixture by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Buy the
same spare parts/components from manufacturer directly.
Avoid direct eye exposure to the light source while it is on.
Do not power on and power off the fixture frequently
When use DMX controller, please make sure that there is no interference sources(e.g.
intercom, high frequency radio waves and radiation source)
Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your local distribution
or after-sale service center.
Section 2. Set Up
Installation
Controlling Board
Machine connection
Installation
This machine should be mounted through the screw holes of truss. Safety rope is a
must to fix fixture well. Make sure truss and safety rope have strong load capacity to

bear more than 3 times of machine weight .
This machine should be installed by qualified technician.

Controlling Board
MENU UP DOWN ENTER
Front display panel

1. LED Display Panel
2. Button
Menu
Switch menu function
UP
Scroll upwards
DOWN
Scroll downwards
ENTER
Confirm by pressing ENTER
3. DMX Signal Input
3 PIN XRL port for DMX512 signal input ( daisy chain);
4. DMX signal output
3 PIN XRL Port for DMX512 signal output ( daisy chain);
5. Power Input
AC power cable port input
6. Switch
On/off
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR connector on the other end.
A word on termination: DMX is a resilient communication protocol, however

errors still occasionally occur. Termination reduces signal errors, and therefore best practices include
use of a terminator in all circumstances. If you are experiencing problems with erratic fixture behavior,
especially over long signal cable runs, a terminator may help improve performance.
To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt resistor, and
wire it between pins 2&3 of the last fixture. They are also readily available from specialty retailers.
Master and slave: select one machine as master, press the menu to choose the function
you want. Press other machines’ address to be DMX state. Use signal cable to connect
machines one by one. Then slave machines will run the same as master machine.
Use controller to control lot of machines: if all machines are set the same menu data, or
different manual data, after use signal cable to connect to controller, all machines will be
controlled by controller. (before connect to controller, all machines should be in the same
channel mode 10ch or 5ch).

Section 3. Troubleshooting
Problem
Probable Cause(s)
Remedy
No power to fixture
Check power cables
Primary fuse blown
Replace fuse
No response from
fixture when power
is applies
Secondary fuse
blown
Replace fuse
Controller not
connected
Connect controller
Incorrect
addressing of the
fixtures
Check address setting on fixture and controller
Bad data link
connection
Inspect cables and correct poor connections
and/or broken cables.
Conflict between
tracking and vector
control
Eliminate scene cross-fade on controller
Data link not
terminated
Insert termination plug in output of last fixture
Fixture resets but
does not respond
correctly to
controller(DMX
mode operation)
Defective fixture or
2 devices
transmitting on link
Bypass fixtures one at a time until normal
operation is regained: unplug both connectors
and connect them directly together
Colors cannot be
mixed
Random color
mixing is on
Turn off random color mixing
Fixture does not
reset correctly
Electronic or
mechanical failure
Contact service technician
Lamp missing or
blown
Disconnect fixture and replace lamp
No light, lamp cuts
out intermittently, or
burns out too
quickly
Fixture or lamp is
too hot
Allow fixture to cool. If problem persists,
contact service technician

Section 4. Reference
Control Menu
DMX Protocol
Dimmer Curve
Specification
Control Menu
No.
Menu
Function
1
d10--
DMX 10 channel control(need connecting controller)
2
d.5--
DMX5 channel control(need connecting controller)
3
r---
r000 to r255: Red from dark to bright
4
g---
g000 to g255: Green from dark to bright
5
b---
b000 to b255: Blue from dark to bright
6
pr--
pr01~pr25：25 kinds of preset colors：
pr01：Red
pr02：Green
pr03: Blue

pr04: Lemon Green
pr05：Yellow Green
pr06：Yellow
pr07：Tea Red
pr08：Light orange
pr09：Rose Red
pr10：pink
pr11：Pink Purple
pr12：Light Purple
pr13：Powder Blue
pr14：Light Blue
pr15：Sky Blue
pr16：Light Cyan
pr17：Turquoise
pr18：Aqua
pr19: Light Green
pr20：Cool White
pr21：Light Cool white
pr22：Pure White
pr23：Purple White
pr24：Rice White
pr25：Warm White
7
F---
F000 to F255：Strobe(from slow to fast)
8
C---
C000 to C255: Full color fade，from slow to fast

9
J---
J000 to J255：Full color jump，from slow to fast
10
S---
S000 to S255：Sound active，from slow to fast
11
T---
on: high temperature with half power function on
off :high temperature with half power function off
When the temperature up to 80 ℃ ， the Max. power consumption would be
50% ; when temp. down to 65℃，the power consumption would be 100%
12
dr--
dr-0：Standard Dimmer Curve；
dr-1：Dimmer Curve1；
dr-2：Dimmer Curve2；
dr-3：Dimmer Curve3；
dr-4：Dimmer Curve4；
DMX protocol
DMX512 Channel Chart：（10CH）
CH
Function
Specification
CH1
Dimmer
0-255 RGBW Dimmer, from dark to bright
CH2
Red dimmer
0-255 Red from dark to bright
CH3
Green dimmer
0-255 Green from dark to bright
CH4
Blue dimmer
0-255 Blue from dark to bright
CH5
000-005 N/A
006-055: Random Strobe
056-105: Pulse Strobe
106-155: Regular Strobe
156-205: Thunder Strobe
206-255: Standard Strobe

Strobe
00-01 N/A
002-043, red from dark to bright
044-085,red from bright to dark, green from dark to bright；
86-127：green from bright to dark, blue from dark to bright；
128-169：red from dark to bright, blue full bright ；
170-211: red full bright, green from dark to bright, blue full
bright;
212-254: red, green, blue full bright, white from dark to bright
255: red, green, blue, white full bright
Color Mixing
Color Preset
0-5：N/A
6-15：Red
16-25：Green
26-35: Blue
36-45：Lemon Green
46-55：Yellow Green
56-65：Yellow
66-75：Tea Red
76-85: Light Orange
86-95：Rose Red
96-105：Pink
106-115：Pink Purple
116-125：Lilac
126-135：Powder Blue
136-145：Light Blue
146-155：Sky Blue

156-165：Light Cyan
166-175：Turquoise
176-185：Aqua
186-195：Light Green
196-205：Cool White
206-215：light cold white
216-225：Pure White
226-235：Purple White
236-245：Rice white
246-255：Warm White
CH8
Auto & Sound
1- 10: N/A
11-40: Full colors fade，
41-70: Red, Green, Blue fade;
71-100: Red, Green, Blue fade+ full bright white
101-130: 7 colors jumping
131-160: Red, Green, Blue Color jumping
161-190, Yellow, Cyan, Purple color jumping
191-220, Sound active Strobe
221-255, Sound active color chasing
CH9
Auto&Sound Speed
0-255 Auto and sound speed ，from slow to fast
CH10
Macro function
0-20：Standard Curve
021-040：Di mmerCurve1；
041-060：Dimmer Curve 2；

061-080：Dimmer Curve 3；
081-100：Dimmer Curve 4；
101-149：N/A
150-155: after 3 second, high temperature with half power
function off；
156-199：N/A
200-205 ：after 3 second, high temperature with half power
function on；
206-255：N/A
DMX512 Channel Chart：（5CH）
CH1
Dimmer
0-255 RGBW Dimmer, from dark to bright
CH2
Red dimmer
0-255 Red from dark to bright
CH3
Green dimmer
0-255 Green from dark to bright
CH4
Blue dimmer
0-255 Blue from dark to bright
CH5
Strobe
000-005 N.A
006-055: Random Strobe
056-105: Pulse Strobe
106-155: Regular Strobe
156-205: Thunder Strobe

206-255: Standard Strobe
Dimmer Curves：
Ramp Effect
Menu
Tup(ms)
Tdown(ms)
Standard Dimmer
Curve
dr-0
0
0
Dimmer Curve 1
dr-1
980
1010
Dimmer Curve 2
dr-2
1210
1320
Dimmer Curve 3
dr-3
1600
1710
Dimmer Curve 4
dr-4
1850
1980

Specification
Voltage：AC110V-240V
Frequency：50/60Hz
Machine Power：300W
Led source: 84*3W RGB TRI Color
Beam Angle：45° /25°（for option)
Strobe: 0~30Hz
Dimmer :1 standard +4 kinds of dimmer methods
Channel：10/5CH（switchable）
Control Mode：DMX512/Manual/Master-Slave/Sound active
Cooling way: 1pcs temperature detect fan
Over heat protection:
When temperature up to 80°C, power consumption reduce to 50%; when temp. down to
65°C,will recover full power consumption to be 100% .
Noise:
Fan speed automatically adjust according machine temperature. The maximum noise is
43.3dB(1m distance)
Display: LED Display
DMX: 3 pin or 5 pin
4 barn-door for option
IP: IP20
Net weight:4.5kg(6.2kg with barn door)
Size:43*22*8.4 cm

本公司有权对此份产品说明书进行修改，恕不另行通知。
Our company reserve right to revise this user manual without notice!
Innovation | Efficiency | Dedication | Harmonious