YOODA ARTISTIC Series Configuration guide

ARTISTIC_1RT | ARTISTIC_5RT | ARTISTIC_15RT
In order to fully explore available functions of ARTISTIC series please take a moment and read this manual before using the device.
ARTISTIC transmitters are compatible with all YOODA brand devices.
Illustrations (from the top):
Fig. 1. 15-channel ARTISTIC remote control with display and timer, black
(ARTISTIC_15RT_B)
Fig. 2. Single-channel ARTISTIC remote control with display and timer, white
(ARTISTIC_1RT)
General information
www.sukcesgroup.pl
1. Control:
can control single motor, or a group
of up to 20 motors on each channel
2. Range:
200 meters outdoor,
35 meters indoor
3. Battery:
1 x CR2430
4. Power supply:
3 V
5. Dimensions:
130 x 44 x 10 mm
6. Transmitting power:
10 mW
7. Operating temperature:
from 0°C to 50°C
8. Protection degree:
IP 30
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters
etc.
Detailed description
LCD display
current
channel
manual
mode
minutes
next channel
previus channel
random mode
auto
mode
hours
UP button
PREVIOUS CHANNEL button P2
programming button
WORK MODE
button
TIME SET
button
battery cover
DOWN button
Single-channel or 5-kchannel or 15-channel
transmitter with timer
(front)
Single-channel or 5-kchannel or 15-channel
transmitter with timer
(back)
NEXT CHANNEL button
STOP button

1. For channel to work correctly when remote is set to automatic mode, it has to be activated. If automatic mode is chosen
for the channel and the channel number is flashing, that means device cannot work in automatic mode. For activation press
and hold for a few seconds P2 programming button – channel number will stop flashing and from now on roller shutter will
work in automatic mode.
2. Difference between automatic time of roller shutter opening and closing cannot be shorter than 32 minutes. In case of
smaller than minimal time difference fault message will appear and none of the changes will be saved.
3. Pressing UP or DOWN button in any mode will show currently set opening/closing time and symbol of current process.
4. Estimated battery lifespan is 1 year if the device runs 4 commends a day in average.
5. Batteries should be changed when device stops reacting to commands.
6. When placing the battery ensure that polarity is correct.
7. Choosing ‘00’ group channel means remote controls all programmed devices on all channels at the same time. No
programming functions can be performed on group channel. All devices programmed to any other channel can be
controlled on group channel without additional programming.
8. For all the programmed devices on every channel to work automatically group channel ‘00’ should be chosen in
automatic mode.
Batteries contain substances that may be hazardous to health and may pollute the environment. Used batteries should
be disposed of properly.
ARTISTIC_1RT | ARTISTIC_5RT | ARTISTIC_15RT
In order to fully explore available functions of ARTISTIC series please take a moment and read this manual before using the device.
ARTISTIC transmitters are compatible with all YOODA brand devices.
Detailed description
www.sukcesgroup.pl
1. Manual working mode: normal working mode, without automatic opening/closing according to preset time.
2. Automatic working mode: normal working mode with automatic opening/closing according to preset time.
3. Random working mode: time controlled work with random opening/closing time (up to 15 minutes difference to preset
opening/closing time).
4. Working mode is changed for all channels of the device at the same time.
Changing work mode
Press
WORK MODE button
on the remote.
Manual working mode. Automatic
working mode.
Random
working mode.
Press
WORK MODE button
on the remote.
Press
WORK MODE button
on the remote.
Every working mode
change results in
switching between
the modes.
Setting current time
1. Time can be set only when device is in manual working mode.
2. Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off
from programming mode without saving any changes.
Using UP and DOWN
buttons set
current time.
Press
WORK MODE button
as many times
as it’s needed
to choose manual
working mode.
Press and hold
TIME SET button
for about 5 seconds.
Press
TIME SET button
to switch between
setting hour or minutes
of current time.
Press
TIME SET button
again to start the timer.
To save settings
press and hold
TIME SET button
for about 5 seconds
(elements on display
will stop flashing).
Current time flashes
on the screen.
Current time
was successfully
changed.
KONIEC
ZMIANY

ARTISTIC_1RT | ARTISTIC_5RT | ARTISTIC_15RT
In order to fully explore available functions of ARTISTIC series please take a moment and read this manual before using the device.
ARTISTIC transmitters are compatible with all YOODA brand devices.
Changing automatic opening time
Changing automatic closing time
www.sukcesgroup.pl
1. Time can be set only when device is in automatic working mode.
2. Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off
from programming mode without saving any changes.
1. Time can be set only when device is in automatic working mode.
2. Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off
from programming mode without saving any changes.
Using UP and DOWN
buttons set
current time.
Press and hold
TIME SET button
for about 5 seconds.
Press
TIME SET button
to switch between
setting hour or minutes
of current time.
To save settings
press and hold
TIME SET button
for about 5 seconds
(elements on display will
stop flashing).
Automatic opening time
flashes on the screen.
Automatic opening
time flashes
was successfully changed.
Display shows current time.
KONIEC
ZMIANY
Press
WORK MODE button
once to switch to
closing time setup.
Press and hold
TIME SET button
for about 5 seconds.
Using UP and DOWN
buttons set
current time.
Press
TIME SET button
to switch between
setting hour or minutes
of current time.
To save settings
press and hold
TIME SET button
for about 5 seconds
(elements on display
will stop flashing).
Automatic closing
time flashes
was successfully changed.
Display shows current time.
KONIEC
ZMIANY
Automatic opening time
flashes on the screen.
Automatic closing time
flashes on the screen.
Programming first transmitter to R-type motors
1. Way of programming first transmitter depends on type of radio receiver. When programming first transmitter please
follow instruction of the device that is going to be controlled by the transmitter.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
3. Programming first transmitter will result in deleting all previously programmed transmitter.
Turn on
power supply
or press microswitch
(for 2 sec.) when power is on.
Motor will make a sound.
Roller shutter will make
an up/down move.
Motor will
make a sound.
Press
programming button
(P2) on the remote.
or
Roller shutter
will make
an up/down move
and the motor will
make a few short
sounds.
Motor will
make a sound.
Press
programming button
(P2) on the remote.
Press
UP button
on the remote.