York H4RA018S06 Quick start guide

TECHNICAL GUIDE
SPLIT-SYSTEM AIR CONDITIONERS
10 SEER – R-22
MODELS: EXPORT ONLY
H*RA018 THRU 060
(1.5 THRU 5 NOMINAL TONS, 1 PH)
Due to continuous product improvement, specifica-
tions are subject to change without notice.
Visit us on the web at www.york.com
Additional rating information can be found at
www.ari.org/aridirectory.
LISTED
CERTIFICATION APPLIES ONLY
WHEN THE COMPLETE
SYSTEM IS LISTED
WITH ARI.
ISO 9001
Certified Quality
Management System
R
N
E
M
P
I
U
Q
E
T
Y
R
A
T
I
N
U
0
1
2
ARI
R
A
D
N
A
T
S
D
I
S
N
O
T
C
E
S
F
O
C
C
I
F
I
T
R
E
N
O
I
T
A
H
T
I
W
C
G
N
I
Y
L
P
M
O
S
A
I
R
A
O
T
D
E
I
F
I
T
R
E
C
R
E
R
U
T
C
A
F
U
N
A
M
C
-
G
N
I
N
O
I
T
I
D
N
O
R
I
A
261648-YTG-A-0706
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
DESCRIPTION
The 10 SEER Series condensing unit is the outdoor part of a
versatile system of air conditioning. It is designed to be cus-
tom-matched with one of UPG’s complete line of evaporator
sections, each designed to serve a specific function. Match-
ing Air Handlers are available for upflow, downflow or hori-
zontal applications to provide a complete system. Electric
Heaters are available if required. Add-On coils are available
for use with upflow, downflow or horizontal furnaces and air
handlers.
WARRANTY
Single Phase Units:
5-year limited parts warranty.
5-year limited compressor warranty.
FEATURES
•QUALITY CONDENSER COILS - The coil is constructed
of enhanced copper tube and aluminum fins.
•COIL PROTECTION - Coils are protected from damage by
a polymer mesh applied between the coil face, and a PVC
coated steel coil guard.
•PROTECTED COMPRESSOR - The compressor is inter-
nally protected against high pressure and temperature.
This is accomplished by the simultaneous operation of
high pressure relief valve and a temperature sensor which
protects the compressor if undesirable operating condi-
tions occur. A liquid line filter-drier further protects the
compressor.
•DURABLE FINISH - The cabinet is made of pre-painted
steel. The pre-treated flat galvanized steel provides a bet-
ter paint to steel bond, which resists corrosion and rust
creep. Special primer formulas and matted desert sand fin-
ish insure less fading when exposed to sunlight.
•LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connec-
tions. Discharge line heat exchanger knockouts are pro-
vided, if required. Available in sweat connect models only.
The unit contains enough refrigerant for matching indoor
coils and 15 feet of interconnecting piping. The small base
dimension means less space is required on the ground or
roof.
•TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscap-
ing. This allows compact location on multi-unit applica-
tions.
•LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise up away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolator mounted compressor and the rippled fins
of the condenser coil muffle the normal fan motor and
compressor operating sounds.
•LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.
•EASY SERVICE ACCESS - Fully exposed refrigerant con-
nections, a single panel covering the electrical controls
and the molex plug in the control box connecting the con-
denser fan, make for easy servicing of the unit.
•SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.
•U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment cer-
tification program, which is based on ARI Standard 210/240.

261648-YTG-A-0706
2Unitary Products Group
PHYSICAL AND ELECTRICAL DATA - 1 Phase
MODEL H4RA018S06 H4RA024S06 H4RA030S06 H4RA036S06 H4RA042S06 H4RA048S06 H4RA060S06
Unit Supply Voltage 208-230V, 1φ, 60Hz
Normal Voltage Range 1187 to 252
Minimum Circuit Ampacity 12.5 15.6 17.5 21.5 26.1 30.1 37.3
Max. Overcurrent Device Amps 220 25 30 35 40 45 60
Min. Overcurrent Device Amps 315 20 20 25 30 35 40
Compressor Type 4RecipRecipRecipRecipRecipRecip
Scroll B
Compressor
Amps Rated Load 9.6 12.1 13.6 16.1 19.8 23 28.9
Locked Rotor 54 57 73 82 97 110 160
Crankcase Heater No No No No No No No
Fan Motor Amps Rated Load 0.5 0.5 0.5 1.4 1.4 1.3 1.3
Fan Diameter Inches 18 18 18 18 18 22 22
Fan Motor Rated HP 1/12 1/12 1/12 1/4 1/4 1/4 1/4 Nominal RPM 1,100 1,100 1,100 1,100 1,100 850 850
Nominal CFM 1,850 1,850 1,900 2,750 2,750 3,250 3,300
Coil Face Area Sq. Ft. 8.00 8.00 9.15 9.15 12.58 15.72 15.72 RowsDeep1111111
Fin / Inches 14 14 18 18 18 18 22
Liquid Line OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line OD (Field Installed) 3/4 3/4 3/4 3/4 3/4 7/8 7/8
Unit Charge (Lbs. - Oz.) 53 - 6 3 - 11 3 - 14 3 - 15 5 - 4 7 - 5 6 - 2
Charge Per Foot, Oz. 0.68 0.68 0.68 0.68 0.68 0.70 0.70
Operating Weight Lbs. 118 123 135 137 161 176 188
1. Rated in accordance with ARI Standard 110, utilization range “A”.
2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.
3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.
4. All scrolls listed with a superscript “B” are Bristol scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.
5. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15
feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.
C
A
B
DIMENSIONS
Unit
Model Dimensions (Inches)
Refrigerant
Connection
Service Valve Size
A1
1. Including Fan Guard.
B C Liquid Vapor
018 17 35 23
3/8” 3/4”
024 17 35 23
030 19 35 23
036 19 35 23
042 25 35 23
048 27 37 27 7/8”
060 27 37 27

261648-YTG-A-0706
Unitary Products Group 3
PROCEDURES:
1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of
interconnecting line tubing.
2. Verify the TXV and additional charge required for specific evaporator coil in the system using the above table.
3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.
4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for
evaporator + adder for line set.
Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 Phase
Outdoor Unit H4RA018S06 H4RA024S06 H4RA030S06 H4RA036S06 H4RA042S06 H4RA048S06 H4RA060S06
Unit Orifice (s) 151,53,55 59,61,63 67,69 71,73,75 75,78,81 78,81,84,87 96
Factory R-22 Charge, lbs-oz 3 - 6 3 - 11 3 - 14 3 - 15 5 - 4 7 - 5 6 - 2
Indoor Coil2,3 Additional Charge, Oz
FC/MC/PC/UC18 53+1459+6–––––
FC/MC/PC/UC24 – 59 + 4 67 + 7 73 + 0 – – –
FC/MC/PC/UC30 – 59 + 4 67 + 7 73 + 0 – – –
FC/MC/PC/UC36 – 59 + 12 67 + 6 71 + 3 – – –
FC/MC/PC/UC42 – – – 71 + 7 75 + 1 – –
FC/MC/PC/UC48 ––––75+981+15–
FC/MC/PC/UC60 ––––78+1481+2096+6
HC18 53+1459+6–––––
HC30 – 59 + 12 67 + 6 71 + 3 – – –
HC36 – – – 71 + 7 75 + 1 – –
HC42 – – – 75 + 11 81 + 7 81 + 13 –
HC60 ––––78+1481+2096+6
HD24 – 63 + 7 67 + 7 73 + 9 – – –
HD36 – – – 73 + 15 78 + 8 78 + 9 –
HD48 –––––81+1696+1
HD60 ––––––96+8
AHP18 53+14––––––
AHP24 53+2359+8–––––
AHP36 – – – 75 + 11 – – –
AHP42 ––––81+7––
AHP48 ––––78+1481+20–
AHP60 –––––81+2096+6
G*FD024(S,H)14,1753+1459+6–––––
G*FD030(S,H)17 –59+467+2––––
G*FD035(S,H)14 –59+467+2––––
G*FD036(S,H)17 – 59 + 12 67 + 6 71 + 3 – – –
G*FD036(S,H)21 – – 69 + 9 71 + 3 – – –
G*FD042(S,H)21 – – – 71 + 7 75 + 1 – –
G*FD046(S,H)17 – – – 71 + 7 75 + 1 – –
G*FD048(S,H)21,24 ––––75+981+15–
G*FD060(S,H)24 ––––78+1481+2096+6
G*FA024S14,17 55 + 3 59 + 0 –––––
G*FA030S14 53 + 14 59 + 6 –––––
G*FA036S14 – 59 + 4 67 + 7 73 + 0 – – –
G*FA036S17,21 – 59 + 4 67 + 2 73 + 0 – – –
G*FA048S17 – – – 71 + 7 75 + 1 – –
G*FA048S21 – – – 75 + 11 81 + 7 81 + 13 –
G*FA060S21,24 ––––78+1481+2096+6
F*FP024 53 + 14 59 + 6 –––––
F*FP030 – 59 + 8 67 + 3 ––––
F*FP036 – – 69 + 9 71 + 3 – – –
F*FP042 – – – 71 + 7 75 + 1 – –
F*FP045 ––––78+14––
F*FP048 ––––75+981+15–
F*FP060 –––––81+2096+6
FOOTNOTES:
1. These orifices are packed in the customer packet of each outdoor unit.
2. Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.
3. PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.

261648-YTG-A-0706
4Unitary Products Group
— = Not applicable.
COOLING CAPACITY - With Air Handler Coils
UNIT
MODEL
AIR HANDLER COIL MODEL1COOLING
MODEL ELECTRIC
HEAT KW2WRATED
CFM NET MBH SEER EER
TOTAL SENS.
1 & 3 PH 10 SEER AC WITH MA
H1RA018S06 MA08B 2,5,8,10 17 FC/MC18B 650 19.0 14.1 10.50 9.80
MA08B 2,5,8,10 17 G*FD024(S,H)17 650 19.0 14.1 10.50 9.80
H1RA024S06
MA08B 2,5,8,10 17 FC/MC18B 800 24.4 18.1 10.50 9.55
MA08B 2,5,8,10 17 FC/MC24B 800 24.0 18.1 10.00 9.00
MA08B 2,5,8,10 17 FC/MC30B 800 24.0 18.1 10.00 9.00
MA08B 2,5,8,10 17 G*FD024(S,H)17 800 24.4 18.1 10.50 9.55
MA08B 2,5,8,10 17 G*FD030(S,H)17 850 25.0 18.5 10.60 9.65
H2RA030S06
MA12B 5,8,10 17 FC/MC24B 1000 29.2 20.3 10.25 9.40
MA12B 5,8,10 17 FC/MC30B 1000 29.2 20.3 10.25 9.40
MA12B 5,8,10 17 FC/MC36B 1000 30.0 22.2 10.50 9.65
MA12B 5,8,10 17 G*FD030(S,H)17 1000 29.0 21.5 10.30 9.45
MA12B 5,8,10 17 G*FD036(S,H)17 1000 30.0 22.2 10.50 9.65
H2RA036S06
MA12B 5,8,10 17 FC/MC24B 1200 33.6 24.9 10.00 9.10
MA12B 5,8,10 17 FC/MC30B 1200 33.6 24.9 10.00 9.10
MA12B 5,8,10 17 FC/MC36B 1200 33.8 25.0 10.00 9.20
MA12B 5,8,10 17 FC/MC42B 1200 34.4 25.5 10.15 9.30
MA12B 5,8,10 17 G*FD036(S,H)17 1200 33.8 25.0 10.00 9.20
MA12B 5,8,10 17 G*FD046(S,H)17 1200 34.4 25.5 10.15 9.30
H1RA042S06
MA16C 5,8,10,15,18,20 21 FC/MC42C 1380 40.0 30.2 10.00 9.05
MA16C 5,8,10,15,18,20 21 FC/MC48C 1450 41.0 30.3 10.10 9.15
MA14D 5,8,10,15,18,20 24 FC/MC48D 1450 41.0 30.3 10.10 9.15
MA16C 5,8,10,15,18,20 21 FC60C 1450 42.0 31.0 10.10 9.50
MA14D 5,8,10,15,18,20 24 FC/MC60D 1450 42.0 31.0 10.10 9.50
MA16C 5,8,10,15,18,20 21 G*FD046(S,H)17 1380 40.0 30.2 10.00 9.05
MA16C 5,8,10,15,18,20 21 G*FD048(S,H)21 1450 41.0 30.3 10.10 9.15
MA14D 5,8,10,15,18,20 24 G*FD048(S,H)24 1450 41.0 30.3 10.10 9.15
MA14D 5,8,10,15,18,20 24 G*FD060(S,H)24 1450 42.0 31.0 10.10 9.50
H1RA048S06
MA16C 5,8,10,15,18,20 21 FC/MC42C 1500 44.5 32.9 10.00 9.15
MA16C 5,8,10,15,18,20 21 FC/MC48C 1600 46.0 34.0 10.10 9.50
MA20D 8,10,15,20,25 24 FC/MC48D 1600 46.0 34.0 10.10 9.50
MA16C 5,8,10,15,18,20 21 FC60C 1600 47.0 34.0 10.40 9.70
MA20D 8,10,15,20,25 24 FC/MC60D 1600 47.0 34.0 10.40 9.70
MA16C 5,8,10,15,18,20 21 G*FD046(S,H)17 1500 44.5 32.9 10.00 9.15
MA16C 5,8,10,15,18,20 21 G*FD048(S,H)21 1600 46.0 34.0 10.10 9.50
MA20D 8,10,15,20,25 24 G*FD048(S,H)24 1600 46.0 34.0 10.10 9.50
MA20D 8,10,15,20,25 24 G*FD060(S,H)24 1600 47.0 34.0 10.40 9.70
H3RA060S06 MA20D 8,10,15,20,25 24 FC/MC60D 1800 56.0 40.2 10.50 9.35
MA20D 8,10,15,20,25 24 G*FD060(S,H)24 1800 56.0 40.2 10.50 9.35
1 & 3 PH 10 SEER AC WITH AHP/SHP
H1RA018S06
AHP18 2,5,8 17 – 650 17.4 12.9 10.00 9.00
AHP24 2,5,8,10 17 – 655 19.0 14.4 10.50 9.90
F*FP018 2,5,8 18 – 650 17.4 12.3 10.00 9.00
F*FP024 5,8,10 18 – 650 17.4 12.9 10.00 9.00
H1RA024S06 AHP24 2,5,8,10 17 – 800 24.0 17.5 10.50 9.10 F*FP024 5,8,10 18 – 800 23.4 17.3 10.00 9.00
F*FP030 5,8,10,15 18 – 800 23.6 17.5 10.00 9.10
H2RA030S06 F*FP030 5,8,10,15 18 – 1000 28.4 21.0 10.00 9.50
F*FP036 5,8,10,15,19 21 – 1000 28.0 20.0 10.00 9.00
H3RA060S06 AHP/SHP60 5,8,10,15,20,25 24 – 1800 56.5 41.0 10.50 9.15
F*FP060 5,8,10,15,20,25 24 – 1800 56.0 41.0 10.00 9.15
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power
input in watt-hours during the same period.
1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.
2. Single phase units require single phase 2HK heaters.

261648-YTG-A-0706
Unitary Products Group 5
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
UNIT MODEL FURNACE** COIL
MODEL
COOLING
CFM RANGE
(MIN.-MAX.) WRATED CFM NET MBH SEER1EER
TOTAL SENS.
H4RA018S06 575
752
14,17 FC/MC/PC/UC18B 650 19.0 14.1 10.50 9.80
14 HC18 650 19.0 14.1 10.50 9.80
14,17 G*FA024S14,17 650 18.0 13.3 10.00 9.20
14 G*FA030S14 650 19.0 14.1 10.50 9.80
17 G*FD024(S,H)17 650 19.0 14.1 10.50 9.80
H4RA024S06 700
900
17 FC/MC/PC/UC18B 800 24.4 18.1 10.50 9.55
17 FC/MC/PC/UC24B 800 24.0 18.1 10.00 9.00
17 FC/MC/PC/UC30B 800 24.0 18.1 10.00 9.00
17 HC18 800 24.4 18.1 10.50 9.55
- HD24 800 24.4 18.1 10.60 9.80
14,17 G*FA024S14,17 850 23.8 17.6 10.00 9.15
14 G*FA030S14 800 24.4 18.1 10.50 9.55
17,21 G*FA036S17,21 850 25.0 18.5 10.00 8.95
17 G*FD024(S,H)17 800 24.4 18.1 10.50 9.55
17 G*FD030(S,H)17 850 25.0 18.5 10.60 9.65
H4RA030S06 875
1125
17 FC/MC/PC/UC24B 1000 29.2 20.3 10.25 9.40
17 FC/MC/PC/UC30B 1000 29.2 20.3 10.25 9.40
17 FC/MC/PC/UC36B 1000 30.0 22.2 10.50 9.65
14 HC30 1000 29.2 20.3 10.25 9.40
17 HC36 1000 30.0 22.2 10.50 9.65
- HD24 1000 29.6 21.9 10.00 9.55
14 G*FA030S14 1000 28.0 20.7 10.00 9.30
17,21 G*FA036S17,21 1000 29.2 20.3 10.25 9.40
14 G*FA036S14 1000 29.0 21.5 10.45 9.45
17 G*FD030(S,H)17 1000 29.0 21.5 10.30 9.45
14 G*FD035(S,H)14 1000 29.0 21.5 10.30 9.45
17 G*FD036(S,H)17 1000 30.0 22.2 10.50 9.65
H4RA036S06 1050
1350
17 FC/MC/PC/UC24B 1200 33.6 24.9 10.00 9.10
17 FC/MC/PC/UC30B 1200 33.6 24.9 10.00 9.10
17 FC/MC/PC/UC36B 1200 33.8 25.0 10.00 9.20
17 FC/MC/PC/UC42B 1200 34.4 25.5 10.15 9.30
14 HC30 1200 33.8 25.0 10.00 9.20
17 HC36 1200 34.4 25.5 10.15 9.30
- HD24 1200 34.4 25.5 10.00 8.90
- HD36 1200 34.8 25.8 10.00 8.95
17,21 G*FA036S17,21 1200 33.6 24.9 10.00 9.10
14 G*FA036S14 1200 33.6 24.9 10.00 9.10
17 G*FA048S17 1200 35.0 25.9 10.30 9.40
21 G*FA048S21 1200 36.0 26.6 10.40 9.40
17 G*FD036(S,H)17 1200 33.8 25.0 10.00 9.20
17 G*FD046(S,H)17 1200 34.4 25.5 10.15 9.30
H4RA042S06 1225
1575
21 FC/MC/PC/UC42C 1380 40.0 30.2 10.00 9.05
21 FC/MC/PC/UC48C 1450 41.0 30.3 10.10 9.15
24 FC/MC/PC/UC48D 1450 41.0 30.3 10.10 9.15
21 FC/MC/PC/UC60C 1450 42.0 31.0 10.10 9.50
24 FC/MC/PC/UC60D 1450 42.0 31.0 10.10 9.50
17 HC36 1380 40.0 30.2 10.00 9.05
21 HC42 1400 41.0 30.3 10.00 9.25
24 HC60 1450 42.0 31.0 10.10 9.50
- HD36 1390 40.5 30.0 10.00 9.05
21 G*FA048S17 1380 40.0 30.2 10.00 9.05
21 G*FA048S21 1400 41.0 30.3 10.00 9.25
21,24 G*FA060S21,24 1400 42.0 31.1 10.00 9.45
21 G*FD046(S,H)17 1380 40.0 30.2 10.00 9.05
21 G*FD048(S,H)21 1450 41.0 30.3 10.10 9.15
24 G*FD048(S,H)24 1450 41.0 30.3 10.10 9.15
24 G*FD060(S,H)24 1450 42.0 31.0 10.10 9.50
For Notes See Page 6.

261648-YTG-A-0706
6Unitary Products Group
H4RA048S06 1400
1800
21 FC/MC/PC/UC42C 1500 44.5 32.9 10.00 9.15
21 FC/MC/PC/UC48C 1600 46.0 34.0 10.10 9.50
24 FC/MC/PC/UC48D 1600 46.0 34.0 10.10 9.50
21 FC/MC/PC/UC60C 1600 47.0 34.0 10.40 9.70
24 FC/MC/PC/UC60D 1600 47.0 34.0 10.40 9.70
21 HC48 1600 45.5 33.7 10.00 9.45
24 HC60 1600 47.0 34.0 10.40 9.70
- HD36 1600 45.5 33.7 10.00 9.50
- HD48 1600 46.5 34.4 10.20 9.65
21 G*FA048S17 1500 44.5 32.9 10.00 9.15
21 G*FA048S21 1600 45.5 33.7 10.00 9.45
21,24 G*FA060S21,24 1600 47.0 34.0 10.40 9.70
21 G*FD046(S,H)17 1500 44.5 32.9 10.00 9.15
21 G*FD048(S,H)21 1600 46.0 34.0 10.10 9.50
24 G*FD048(S,H)24 1600 46.0 34.0 10.10 9.50
24 G*FD060(S,H)24 1600 47.0 34.0 10.40 9.70
H4RA060S06 1600
2100
24 FC/MC/PC/UC60D 1800 56.0 40.2 10.50 9.35
24 HC60 1800 56.0 40.2 10.50 9.35
- HD48 2000 55.5 40.0 10.50 9.15
21,24 G*FA060S21,24 1800 56.0 40.2 10.50 9.35
24 G*FD060(S,H)24 1800 56.0 40.2 10.50 9.35
1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one.
** Refer to Quick Selection Chart for specific furnace match-up.
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils (Continued)
UNIT MODEL FURNACE** COIL
MODEL
COOLING
CFM RANGE
(MIN.-MAX.) WRATED CFM NET MBH SEER1EER
TOTAL SENS.

261648-YTG-A-0706
Unitary Products Group 7
ACCESSORIES
*Refer to Price Manual for specific model numbers.
HARD START KIT - Provides increased starting torque for
areas with low voltage.
COMPRESSOR BLANKET - Designed to further reduce the
normal compressor operating sound. Refer to price pages for
specific match-ups.
OFF CYCLE TIMER DELAY - Provides a 5-minute off cycle
to prevent rapid recycling of the compressor.
ROOM THERMOSTATS - A wide selection of compatible
thermosets are available to provide optimum performance
and features for any installation.
1H/1C, manual change-over electronic non-programmable
thermostat.
1H/1C, auto/manual changeover, electronic programmable,
deluxe 7-day, thermostat.
1H/1C, auto/manual changeover, electronic programmable.
* For the most current accessory information, refer to the
price book or consult factory.
SOUND POWER RATINGS*
* Rated in accordance with ARI 270-95 Standards.
TYPICAL INSTALLATION
TYPICAL FIELD WIRING - 1 Phase Application
UNIT MODEL (dBA)
018 76
024 78
030 82
036 82
042 82
048 82
060 80
MINIMUM 24” SERVICE ACCESS
CLEARANCE ON ONE SIDE
60” OVERHEAD
CLEARANCE
10” CLEARANCE
COIL AREA
WEATHERPROOF
DISCONNECT
SWITCH
THERMOSTAT TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK
NEC CLASS 1 WIRING
NEC CLASS 2 WIRING
TO INDOOR COIL
SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT
CONTROL ACCESS PANEL
NOTE: ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.
ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES
POWER WIRING
208/230-1-60
CONTACTOR
TERMINALS
COIL
GND.
LUG
CYRGW
YRGW
POWER WIRING
CONTROL WIRING
FACTORY WIRING
24 VOLT CONTROL WIRING
MINIMUM 18 GA. WIRE
(NEC CLASS 2)
FURNACE OR AIR HANDLER TERMINAL BLOCK
ROOM THERMOSTAT
CONDENSING UNIT
ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.
TERMINAL W IS ONLY
REQUIRED ON SYSTEMS
WITH HEAT.
*
*

261648-YTG-A-0706
8Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H1RA018S06
INDOOR COIL MODEL NO. G1FA024S14,17
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 550 650 750
ID DB (°F) 85 80 70 85 80 70 85 80 70
ID WB (°F) 72 67 57 72 67 57 72 67 57
75 T.C. 20.6 19.7 18.1 20.7 19.8 18.5 20.8 19.8 18.9 S.C. 12.7 12.8 12.3 13.3 13.5 13.4 13.7 13.8 14.0
K.W 1.68 1.65 1.64 1.72 1.71 1.70 1.75 1.74 1.73
85 T.C. 20.6 19.3 17.4 20.9 19.6 18.0 21.1 19.8 18.4 S.C. 12.7 12.6 11.9 13.5 13.4 13.1 14.1 14.0 13.8
K.W 1.58 1.54 1.53 1.62 1.59 1.58 1.65 1.63 1.62
95 T.C. 19.0 17.5 15.5 19.5 18.0 16.1 19.8 18.2 16.5 S.C. 12.8 12.4 11.5 13.7 13.3 12.8 14.5 14.1 13.6
K.W 1.97 1.91 1.90 2.02 1.96 1.95 2.05 2.00 1.99
105 T.C. 18.4 16.6 14.2 18.9 17.1 15.0 19.2 17.4 15.4 S.C. 12.5 11.8 10.7 13.6 12.8 12.0 14.4 13.7 12.8
K.W 1.82 1.77 1.75 1.88 1.82 1.80 1.91 1.86 1.83
115 T.C. 16.3 14.5 11.9 16.9 15.0 12.7 17.2 15.2 13.1 S.C. 12.3 11.2 10.0 13.5 12.4 11.2 14.3 13.2 12.0
K.W 2.24 2.19 2.14 2.31 2.24 2.19 2.35 2.28 2.22
125 T.C. 14.3 12.3 9.7 14.9 13.0 10.5 15.2 13.1 10.8 S.C. 12.0 10.6 9.3 13.3 11.9 10.4 14.2 12.8 11.2
K.W 2.66 2.61 2.53 2.74 2.66 2.58 2.79 2.70 2.61
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM
Air Handler Coil T.C. S.C. KW
MA08B FC / MC18B 1.06 1.06 0.94
MA08B G*FD024(S,H)17 1.06 1.06 0.94
AHP18 - 0.97 0.97 1.02
AHP24 - 1.06 1.08 0.93
F*FP018 - 0.97 0.92 1.02
F*FP024 - 0.97 0.97 1.02
- FC/MC/PC/UC18B 1.06 1.06 0.94
- G*FA030S14 1.06 1.06 0.94
- G*FD024(S,H)17 1.06 1.06 0.94
- HC18 1.06 1.06 0.94

261648-YTG-A-0706
Unitary Products Group 9
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H1RA024S06
INDOOR COIL MODEL NO. G1FA024S14, 17
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 600 800 1000
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 28.3 25.9 22.7 21.4 28.7 25.1 24.4 21.8 27.5 26.6 24.5 20.9 S.C. 16.9 16.9 15.4 17.0 17.7 16.8 17.0 17.8 17.1 18.0 17.3 17.3
K.W 2.04 1.94 1.78 1.78 2.05 1.87 1.89 1.80 1.97 1.98 1.89 1.72
85 T.C. 28.5 26.0 22.8 21.4 28.9 25.2 24.4 21.8 27.7 26.7 24.6 20.9 S.C. 17.5 17.5 16.0 17.6 18.5 17.6 17.9 18.7 18.0 19.0 18.2 18.3
K.W 2.25 2.14 1.95 1.95 2.28 2.06 2.07 1.96 2.18 2.18 2.07 1.88
95 T.C. 26.9 24.5 21.4 20.1 27.3 23.7 23.0 20.6 26.2 25.2 23.0 19.8 S.C. 17.4 17.4 15.9 17.5 18.5 17.6 17.9 18.8 18.1 19.0 18.3 18.4
K.W 2.42 2.28 2.06 2.06 2.44 2.20 2.20 2.08 2.34 2.32 2.21 1.99
105 T.C. 24.7 22.4 19.5 18.3 24.8 21.6 20.9 18.6 23.8 22.8 21.1 17.9 S.C. 16.8 16.8 15.3 16.9 17.9 16.9 17.3 17.9 17.6 18.4 17.6 17.5
K.W 2.52 2.37 2.15 2.14 2.54 2.30 2.29 2.17 2.43 2.43 2.30 2.07
115 T.C. 22.0 19.9 17.4 16.3 22.2 19.3 18.6 16.9 21.2 20.4 18.8 16.2 S.C. 15.8 15.7 14.3 15.8 17.0 16.2 16.2 16.7 16.7 17.5 16.8 16.1
K.W 2.60 2.45 2.23 2.20 2.63 2.36 2.37 2.25 2.51 2.50 2.37 2.17
125 T.C. 19.4 17.5 15.3 14.2 19.5 16.9 16.3 15.1 18.6 17.9 16.5 14.6 S.C. 14.7 14.7 13.3 14.6 16.0 15.4 15.1 15.4 15.9 16.6 15.9 14.6
K.W 2.68 2.53 2.31 2.26 2.71 2.43 2.44 2.33 2.59 2.57 2.44 2.27
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
MA08B FC / MC18B 1.03 1.03 0.96
MA08B FC / MC24B 1.01 1.03 1.02
MA08B FC / MC30B 1.01 1.03 1.02
MA08B G*FD024(S,H)17 1.03 1.03 0.96
MA08B G*FD030(S,H)17 1.05 1.05 0.95
AHP24 - 1.01 0.99 1.01
F*FP024 - 0.98 0.98 1.02
F*FP030 - 0.99 0.99 1.01
- FC/MC/PC/UC18B 1.03 1.03 0.96
- FC/MC/PC/UC24B 1.01 1.03 1.02
- FC/MC/PC/UC30B 1.01 1.03 1.02
- G*FA030S14 1.03 1.03 0.96
- G*FA036S17,21 1.05 1.05 1.02
- G*FD024(S,H)17 1.03 1.03 0.96
- G*FD030(S,H)17 1.05 1.05 0.95
- HC18 1.03 1.03 0.96
- HD24 1.03 1.03 0.93

261648-YTG-A-0706
10 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H2RA030S06
INDOOR COIL MODEL NO. G1FA036S17,21
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 800 1000 1200
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 33.9 31.1 28.7 25.6 34.4 31.5 29.1 26.0 34.7 31.8 29.4 26.3 S.C. 20.5 20.6 19.7 20.7 21.4 21.4 20.6 21.6 22.2 22.2 21.4 22.5
K.W 2.69 2.64 2.59 2.52 2.78 2.73 2.68 2.61 2.86 2.81 2.76 2.69
85 T.C. 33.0 30.2 27.8 24.9 33.4 30.6 28.2 25.5 33.7 30.9 28.5 25.9 S.C. 20.6 20.7 19.9 20.9 21.6 21.7 20.9 22.1 22.6 22.6 21.7 23.0
K.W 2.87 2.79 2.72 2.64 2.94 2.88 2.82 2.75 3.02 2.96 2.90 2.84
95 T.C. 31.3 28.7 26.4 23.7 31.7 29.0 26.7 24.1 31.9 29.2 27.1 24.4 S.C. 20.3 20.4 19.5 20.8 21.5 21.5 20.7 21.6 22.4 22.5 21.7 22.7
K.W 3.07 2.98 2.91 2.81 3.15 3.07 3.00 2.92 3.25 3.16 3.10 2.99
105 T.C. 29.3 26.7 24.6 22.0 29.5 27.0 25.0 22.4 29.7 27.2 25.2 23.1 S.C. 19.9 19.9 19.2 20.0 21.0 21.0 20.1 21.1 22.1 22.1 21.1 22.2
K.W 3.27 3.17 3.09 2.98 3.37 3.27 3.19 3.07 3.45 3.37 3.28 3.19
115 T.C. 26.9 24.5 22.6 20.3 27.1 24.8 22.9 21.0 27.2 25.1 23.1 21.4 S.C. 19.2 19.1 18.3 19.1 20.3 20.3 19.3 20.2 21.2 21.2 20.2 20.6
K.W 3.48 3.37 3.26 3.14 3.57 3.47 3.36 3.26 3.67 3.56 3.46 3.35
125 T.C. 24.5 22.3 20.7 18.6 24.7 22.6 20.9 19.6 24.7 23.0 21.1 19.7 S.C. 18.5 18.3 17.4 18.2 19.6 19.6 18.4 19.3 20.3 20.3 19.3 19.0
K.W 3.69 3.57 3.43 3.30 3.77 3.67 3.53 3.45 3.89 3.75 3.64 3.51
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
MA12B FC / MC24B 1.00 1.00 1.00
MA12B FC / MC30B 1.00 1.00 1.00
MA12B FC / MC36B 1.03 1.09 0.97
MA12B G*FD030(S,H)17 0.99 1.06 0.99
MA12B G*FD036(S,H)17 1.03 1.09 0.97
F*FP030 - 0.97 1.03 0.99
F*FP036 - 0.96 0.99 1.04
- FC/MC/PC/UC24B 1.00 1.00 1.00
- FC/MC/PC/UC30B 1.00 1.00 1.00
- FC/MC/PC/UC36B 1.03 1.09 0.97
- G*FA030S14 0.96 1.02 1.01
- G*FA036S14 0.99 1.06 0.99
- G*FD030(S,H)17 0.99 1.06 0.99
- G*FD035(S,H)14 0.99 1.06 0.99
- G*FD036(S,H)17 1.03 1.09 0.97
- HC30 1.00 1.00 1.00
- HC36 1.03 1.09 0.97
- HD24 1.01 1.08 0.98

261648-YTG-A-0706
Unitary Products Group 11
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H2RA036S06
INDOOR COIL MODEL NO. G1FA036S17,21
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1150 1250 1350
ID DB (°F) 85 80 70 85 80 70 85 80 70
ID WB (°F) 72 67 57 72 67 57 72 67 57
75 T.C. 38.3 36.1 34.4 37.9 36.3 34.6 38.0 36.4 34.9 S.C. 24.0 23.7 24.0 24.1 24.5 24.7 24.7 25.3 25.2
K.W 3.19 3.14 3.09 3.23 3.20 3.14 3.26 3.23 3.18
85 T.C. 36.9 34.6 32.2 36.9 34.9 32.6 37.0 35.2 33.0 S.C. 24.2 23.7 22.9 24.7 24.6 23.9 25.3 25.5 24.8
K.W 3.45 3.39 3.30 3.50 3.44 3.36 3.53 3.49 3.40
95 T.C. 35.5 33.2 30.0 35.8 33.6 30.4 36.0 34.0 31.0 S.C. 24.3 23.6 21.9 25.4 24.9 23.6 26.0 25.6 24.4
K.W 3.71 3.63 3.52 3.76 3.69 3.58 3.80 3.75 3.62
105 T.C. 33.2 30.4 26.7 33.4 30.8 27.2 33.6 31.3 27.7 S.C. 23.7 22.5 20.7 24.5 23.6 21.9 25.4 24.6 23.0
K.W 3.97 3.84 3.71 4.02 3.91 3.77 4.06 3.96 3.81
115 T.C. 31.0 27.6 23.5 31.1 28.2 24.2 31.3 28.5 24.4 S.C. 23.1 21.3 19.6 23.9 22.6 20.7 24.8 23.7 21.6
K.W 4.22 4.06 3.90 4.29 4.13 3.94 4.33 4.18 4.00
125 T.C. 28.7 24.8 20.2 28.9 25.6 21.1 29.0 25.7 21.0 S.C. 22.5 20.2 18.4 23.2 21.6 19.6 24.2 22.7 20.2
K.W 4.47 4.28 4.09 4.56 4.35 4.11 4.60 4.40 4.19
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM
Air Handler Coil T.C. S.C. KW
MA12B FC / MC24B 1.00 1.00 1.00
MA12B FC / MC30B 1.00 1.00 1.00
MA12B FC / MC36B 1.01 1.00 0.99
MA12B FC / MC42B 1.02 1.02 0.98
MA12B G*FD036(S,H)17 1.01 1.00 0.99
MA12B G*FD046(S,H)17 1.02 1.02 0.98
AHP36 - 1.04 0.97 0.83
F*FP036 - 1.02 1.41 0.98
F*FP042 - 1.02 1.01 0.99
- FC/MC/PC/UC24B 1.00 1.00 1.00
- FC/MC/PC/UC30B 1.00 1.00 1.00
- FC/MC/PC/UC36B 1.01 1.00 0.99
- FC/MC/PC/UC42B 1.02 1.02 0.98
- G*FA036S14 1.00 1.00 1.00
- G*FA048S17 1.04 1.04 0.97
- G*FA048S21 1.07 1.07 0.97
- G*FD036(S,H)17 1.01 1.00 0.99
- G*FD046(S,H)17 1.02 1.02 0.98
- HC30 1.01 1.00 0.99
- HC36 1.02 1.02 0.98
- HD24 1.02 1.02 1.02
- HD36 1.04 1.04 1.02

261648-YTG-A-0706
12 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H1RA042S06
INDOOR COIL MODEL NO. G1FA048S21
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1200 1400 1600
ID DB (°F) 85 80 70 85 80 70 85 80 70
ID WB (°F) 72 67 57 72 67 57 72 67 57
75 T.C. 47.2 44.1 41.2 47.5 44.6 41.9 47.9 45.1 42.6 S.C. 30.2 29.6 29.4 31.9 31.1 31.0 33.6 32.6 32.6
K.W 3.90 3.85 3.78 4.05 3.99 3.94 4.19 4.14 4.09
85 T.C. 45.5 42.1 38.5 45.9 42.8 39.3 46.3 43.4 40.2 S.C. 29.8 28.9 28.1 31.4 30.7 30.0 33.0 32.5 31.9
K.W 4.13 4.06 3.96 4.28 4.21 4.13 4.43 4.36 4.29
95 T.C. 43.9 40.2 35.7 44.3 41.0 36.8 44.8 41.8 37.8 S.C. 29.5 28.2 26.9 30.9 30.3 29.1 32.4 32.4 31.2
K.W 4.36 4.27 4.14 4.52 4.43 4.31 4.67 4.59 4.49
105 T.C. 40.5 36.3 32.0 41.2 37.1 32.8 42.0 38.0 33.7 S.C. 28.1 26.7 25.1 29.9 28.8 27.2 31.7 30.9 29.3
K.W 4.58 4.44 4.30 4.74 4.60 4.47 4.89 4.77 4.64
115 T.C. 37.1 32.3 28.3 38.2 33.3 28.9 39.2 34.2 29.6 S.C. 26.8 25.1 23.3 29.0 27.2 25.4 31.1 29.4 27.4
K.W 4.81 4.62 4.45 4.96 4.78 4.62 5.10 4.95 4.79
125 T.C. 33.7 28.4 24.5 35.1 29.4 25.0 36.4 30.4 25.4 S.C. 25.5 23.5 21.5 28.0 25.7 23.5 30.5 27.9 25.5
K.W 5.04 4.79 4.61 5.18 4.96 4.78 5.32 5.13 4.94
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
MA16C FC / MC42C 0.98 1.00 1.02
MA16C FC / MC48C 1.00 1.00 1.01
MA14D FC / MC48D 1.00 1.00 1.01
MA14D FC / MC60D 1.02 1.02 0.97
MA16C FC60C 1.02 1.02 0.97
MA16C G*FD046(S,H)17 0.98 1.00 1.02
MA16C G*FD048(S,H)21 1.00 1.00 1.01
MA14D G*FD048(S,H)24 1.00 1.00 1.01
MA14D G*FD060(S,H)24 1.02 1.02 0.97
AHP42 - 0.98 0.99 1.01
F*FP042 - 0.96 0.95 1.03
F*FP048 - 0.99 0.99 1.01
- FC/MC/PC/UC42C 0.98 1.00 1.02
- FC/MC/PC/UC48C 1.00 1.00 1.01
- FC/MC/PC/UC48D 1.00 1.00 1.01
- FC/MC/PC/UC60C 1.02 1.02 0.97
- FC/MC/PC/UC60D 1.02 1.02 0.97
- G*FA048S17 0.98 1.00 1.02
- G*FA060S21,24 1.02 1.03 0.98
- G*FD046(S,H)17 0.98 1.00 1.02
- G*FD048(S,H)21 1.00 1.00 1.01
- G*FD048(S,H)24 1.00 1.00 1.01
- G*FD060(S,H)24 1.02 1.02 0.97
- HC36 0.98 1.00 1.02
- HC42 1.00 1.00 1.00
- HC60 1.02 1.02 0.97
- HD36 0.99 0.99 1.02

261648-YTG-A-0706
Unitary Products Group 13
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H1RA048S06
INDOOR COIL MODEL NO. G1FA048S21
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 1200 1400 1600
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57
75 T.C. 53.4 48.9 45.1 40.2 54.3 49.8 45.9 41.3 54.9 50.3 46.4 41.8 S.C. 32.2 32.3 31.0 32.5 34.0 34.0 32.7 34.7 35.2 35.3 33.9 35.9
K.W 4.32 4.15 4.00 3.83 4.44 4.26 4.11 3.95 4.53 4.36 4.21 4.04
85 T.C. 52.0 47.5 43.7 39.2 52.7 48.3 44.5 40.0 53.2 48.7 45.2 40.5 S.C. 32.2 32.3 31.1 32.7 34.1 34.1 32.8 34.7 35.4 35.5 34.5 36.0
K.W 4.62 4.43 4.26 4.07 4.74 4.55 4.38 4.18 4.84 4.65 4.48 4.28
95 T.C. 49.0 44.9 41.3 36.9 49.6 45.5 42.0 37.6 50.0 45.8 42.4 38.3 S.C. 31.6 31.6 30.4 31.8 33.5 33.7 32.4 33.8 34.9 35.0 33.7 35.6
K.W 4.91 4.70 4.51 4.31 5.02 4.81 4.64 4.43 5.13 4.92 4.74 4.53
105 T.C. 45.6 41.6 38.4 34.3 46.0 42.2 39.0 35.0 46.2 42.5 39.3 36.2 S.C. 30.5 30.6 29.5 30.9 32.6 32.8 31.5 32.8 34.1 34.2 32.7 34.5
K.W 5.18 4.96 4.76 4.54 5.30 5.07 4.88 4.67 5.39 5.18 4.99 4.83
115 T.C. 41.8 38.3 35.3 31.7 42.3 38.8 35.8 33.0 42.5 39.0 36.2 33.5 S.C. 29.3 29.5 28.2 29.6 31.6 31.4 30.1 31.5 33.0 32.9 31.5 32.0
K.W 5.42 5.18 4.98 4.76 5.52 5.31 5.10 4.94 5.63 5.41 5.21 5.06
125 T.C. 38.0 35.0 32.3 29.1 38.6 35.4 32.7 31.0 38.8 35.5 33.2 30.8 S.C. 28.1 28.4 26.9 28.3 30.6 30.0 28.7 30.2 31.9 31.6 30.4 29.5
K.W 5.66 5.40 5.20 4.98 5.74 5.55 5.32 5.21 5.87 5.64 5.43 5.29
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
MA16C FC / MC42C 0.97 0.97 1.04
MA16C FC / MC48C 1.00 1.00 1.00
MA20D FC / MC48D 1.00 1.00 1.00
MA20D FC / MC60D 1.02 1.00 0.98
MA16C FC60C 1.02 1.00 0.98
MA16C G*FD046(S,H)17 0.97 0.97 1.04
MA20D G*FD048(S,H)24 1.00 1.00 1.00
MA20D G*FD060(S,H)24 1.02 1.00 0.98
AHP / SHP48 - 1.02 1.01 0.98
AHP / SHP60 - 1.02 1.01 0.98
F*FP048 - 0.99 0.99 1.04
F*FP060 - 1.01 1.01 0.98
- FC/MC/PC/UC42C 0.97 0.97 1.04
- FC/MC/PC/UC48C 1.00 1.00 1.00
- FC/MC/PC/UC48D 1.00 1.00 1.00
- FC/MC/PC/UC60C 1.02 1.00 0.98
- FC/MC/PC/UC60D 1.02 1.00 0.98
- G*FA048S17 0.97 0.97 1.04
- G*FA048S21 0.99 0.99 1.01
- G*FA060S21,24 1.02 1.00 0.98
- G*FD046(S,H)17 0.97 0.97 1.04
- G*FD048(S,H)21 1.00 1.00 1.00
- G*FD048(S,H)24 1.00 1.00 1.00
- G*FD060(S,H)24 1.02 1.00 0.98
- HC48 0.99 0.99 1.01
- HC60 1.02 1.00 0.98
- HD36 0.99 0.99 1.00
- HD48 1.01 1.01 0.98

261648-YTG-A-0706
14 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H3RA060S06
INDOOR COIL MODEL NO. G1FA060S21,24
CONDENSER
ENTERING AIR
TEMPERATURE
ID CFM 2050 1800 1550
ID DB (°F) 85 80 70 85 80 70 85 80 70
ID WB (°F) 72 67 57 72 67 57 72 67 57
75 T.C. 64.7 61.9 58.2 64.1 61.2 57.2 63.6 60.5 56.2 S.C. 46.3 44.9 42.9 43.3 42.1 40.3 40.3 39.3 37.7
K.W 5.18 5.13 5.03 5.08 5.02 4.92 4.97 4.91 4.81
85 T.C. 62.8 59.6 55.4 62.3 58.6 54.3 61.8 57.6 53.3 S.C. 45.9 44.3 41.9 42.8 41.2 39.2 39.7 38.2 36.5
K.W 4.94 4.86 4.77 5.58 5.50 5.40 5.48 5.40 5.28
95 T.C. 60.9 57.3 52.7 60.4 56.0 51.5 59.9 54.7 50.3 S.C. 45.7 43.5 40.8 42.4 40.2 38.0 39.2 37.0 35.2
K.W 6.19 6.10 6.00 6.09 5.99 5.87 5.98 5.88 5.74
105 T.C. 57.2 53.4 48.4 56.6 52.3 47.4 56.0 51.1 46.4 S.C. 44.6 42.1 39.3 41.3 39.0 36.6 38.0 35.9 33.8
K.W 6.82 6.70 6.56 6.71 6.59 6.44 6.60 6.47 6.31
115 T.C. 53.5 49.5 44.1 52.8 48.5 43.3 52.1 47.5 42.4 S.C. 43.6 40.5 37.7 40.2 37.6 35.1 36.8 34.7 32.4
K.W 7.47 7.32 7.14 7.35 7.19 7.01 7.22 7.06 6.88
125 T.C. 49.8 45.6 39.9 49.0 44.8 39.2 48.2 43.9 38.5 S.C. 42.5 39.0 36.1 39.0 36.3 33.6 35.6 33.6 31.0
K.W 8.12 7.94 7.72 7.99 7.79 7.58 7.84 7.65 7.45
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
MA20D FC / MC60D 1.00 1.00 1.00
MA20D G*FD060(S,H)24 1.00 1.00 1.00
AHP / SHP60 - 1.01 1.02 1.02
F*FP060 - 1.00 1.02 1.02
- G*FA060S21,24 1.00 1.00 1.00
- G*FD060(S,H)24 1.00 1.00 1.00
- HC60 1.00 1.00 1.00
- HD48 0.99 1.00 1.02

261648-YTG-A-0706
Unitary Products Group 15
NOTES

Subject to change without notice. Printed in U.S.A. 261648-YTG-A-0706
Copyright © by York International Corp. 2006. All rights reserved. Supersedes: Nothing
Unitary 5005 Norman
Products York OK
Group Drive 73069