York Predator BP078 User manual

INSTALLATION
MANUAL
CAUTION: READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
SINGLE PACKAGE HEAT PUMP
HIGH EFFICIENCY
BP078, 090, 102, 120 AND 150
(6-1/2 TO 12-1/2 TON)
127421-YIM-C-0606
®
CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY CONSIDERATIONS. . . . . . . . . . . . . . . . . .5
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
REFERENCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . .5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . .6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
START-UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . .48
See following pages for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given to
prevent equipment damage. Warnings are given to alert
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly. Tested in accordance with:

127421-YIM-C-0606
2Unitary Products Group
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . 5
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RENEWAL PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION SAFETY INFORMATION . . . . . . . . . . . .7
PRECEDING INSTALLATION. . . . . . . . . . . . . . . . . . . . . . 7
LIMITATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
LOCATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
RIGGING AND HANDLING . . . . . . . . . . . . . . . . . . . . . . . . 9
CLEARANCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
DUCT COVERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDENSATE DRAIN . . . . . . . . . . . . . . . . . . . . . . . . . .14
COMPRESSORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
THERMOSTAT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . 14
POWER AND CONTROL WIRING . . . . . . . . . . . . . . . . .14
POWER WIRING DETAIL . . . . . . . . . . . . . . . . . . . . . . . .15
FACTORY INSTALLED OPTIONS/
FIELD INSTALLED ACCESSORIES . . . . . . . . . . . . . . . .22
ELECTRIC HEAT ACCESSORY . . . . . . . . . . . . . . . . . . . . . . .22
ELECTRIC HEAT OPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . .22
MOTORIZED OUTDOOR DAMPER . . . . . . . . . . . . . . . . . . . .23
ECONOMIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
POWER EXHAUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RAIN HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ECONOMIZER AND POWER EXHAUST SET
POINT ADJUSTMENTS AND INFORMATION . . . . . . . . 23
MINIMUM POSITION ADJUSTMENT . . . . . . . . . . . . . . . . . . .23
ENTHALPY SET POINT ADJUSTMENT . . . . . . . . . . . . . . . . .23
POWER EXHAUST DAMPER SET POINT
(WITH OR WITHOUT POWER EXHAUST) . . . . . . . . . . . . . . .23
INDOOR AIR QUALITY AQ . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PHASING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
BLOWER ROTATION . . . . . . . . . . . . . . . . . . . . . . . . . . .25
BELT TENSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
AIR BALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CHECKING AIR QUANTITY . . . . . . . . . . . . . . . . . . . . . . 37
METHOD ONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
METHOD TWO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SUPPLY AIR DRIVE ADJUSTMENT . . . . . . . . . . . . . . . 39
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
SEQUENCE OF OPERATIONS OVERVIEW . . . . . . . . . 41
COOLING SEQUENCE OF OPERATION. . . . . . . . . . . . 41
CONTINUOUS BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
INTERMITTENT BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
NO OUTDOOR AIR OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . .41
ECONOMIZER WITH SINGLE ENTHALPY SENSOR . . . . . . .41
ECONOMIZER WITH DUAL ENTHALPY SENSORS. . . . . . . .42
ECONOMIZER (SINGLE OR DUAL) WITH
POWER EXHAUST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
MOTORIZED OUTDOOR AIR DAMPERS . . . . . . . . . . . . . . . .42
COOLING OPERATION ERRORS. . . . . . . . . . . . . . . . . . . . . .42
HIGH-PRESSURE LIMIT SWITCH. . . . . . . . . . . . . . . . . . . . . .42
LOW-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . . . . . . . .42
FREEZESTAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
LOW AMBIENT COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
COMPRESSOR PROTECTION . . . . . . . . . . . . . . . . . . . 43
FLASH CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
HEATING SEQUENCE OF OPERATION . . . . . . . . . . . . 43
ELECTRIC HEAT OPERATION ERRORS . . . . . . . . . . . 44
TEMPERATURE LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
LIMIT SWITCH (LS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
FLASH CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . . . . 45
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
PRESTART CHECK LIST. . . . . . . . . . . . . . . . . . . . . . . . 45
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . 45
POST START CHECK LIST . . . . . . . . . . . . . . . . . . . . . . 45
SUPERHEAT CHARGING METHOD . . . . . . . . . . . . . . . . 45
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
PREDATOR® FLASH CODES . . . . . . . . . . . . . . . . . . . . 48
COOLING TROUBLESHOOTING GUIDE. . . . . . . . . . . . 50

127421-YIM-C-0606
Unitary Products Group 3
LIST OF FIGURES
Fig. # Pg. #
1 UNIT SHIPPING BRACKET . . . . . . . . . . . . . . . . . . . . . . . .7
2 CONDENSER COIL COVERING . . . . . . . . . . . . . . . . . . . .7
3 COMPRESSOR SECTION . . . . . . . . . . . . . . . . . . . . . . . . .7
4 PREDATOR® COMPONENT LOCATION . . . . . . . . . . . . .8
5 UNIT 4 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
6 UNIT 6 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
7 UNIT CENTER OF GRAVITY . . . . . . . . . . . . . . . . . . . . . .10
8 UNIT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
9 BOTTOM DUCT OPENINGS . . . . . . . . . . . . . . . . . . . . . .11
10 REAR DUCT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . .12
11 PREDATOR® ROOF CURB DIMENSIONS . . . . . . . . . . .13
12 SUNLINE™ TO PREDATOR® TRANSITION ROOF
CURBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Fig. # Pg. #
13 SIDE PANELS WITH HOLE PLUGS . . . . . . . . . . . . . . . . 13
14 RETURN DOWNFLOW PLENUM WITH PANEL . . . . . . . 14
15 DISCHARGE PANEL IN PLACE . . . . . . . . . . . . . . . . . . .14
16 CONDENSATE DRAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
17 ELECTRONIC THERMOSTAT FIELD WIRING . . . . . . . . 15
18 FIELD WIRING 24 VOLT THERMOSTAT . . . . . . . . . . . .16
19 FIELD WIRING DISCONNECT. . . . . . . . . . . . . . . . . . . . . 16
20 ENTHALPY SET POINT CHART . . . . . . . . . . . . . . . . . . .24
21 HONEYWELL ECONOMIZER CONTROL W7212. . . . . . 24
22 BELT ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
23 DRY COIL DELTA P 50” CABINET . . . . . . . . . . . . . . . . . 38
24 DRY COIL DELTA P 42” CABINET . . . . . . . . . . . . . . . . . 38
25 UNIT CONTROL BOARD. . . . . . . . . . . . . . . . . . . . . . . . .49

127421-YIM-C-0606
4Unitary Products Group
LIST OF TABLES
Tbl. # Pg. #
1 UNIT VOLTAGE LIMITATIONS. . . . . . . . . . . . . . . . . . . . . 8
2 UNIT TEMPERATURE LIMITATIONS. . . . . . . . . . . . . . . . 8
3 UNIT WEIGHTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 4 POINT LOAD WEIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 6 POINT LOAD WEIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 UNIT HEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7 UNIT CLEARANCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8 CONTROL WIRE SIZES . . . . . . . . . . . . . . . . . . . . . . . . . 14
9 ELECTRICAL DATA BP078 (6-1/2 TON) HP W/O PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 17
10 ELECTRICAL DATA BP078 (6-1/2 TON) HP WITH PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 17
11 ELECTRICAL DATA BP090 (7-1/2 TON) HP W/O PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 18
12 ELECTRICAL DATA BP090 (7-1/2 TON) HP WITH PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 18
13 ELECTRICAL DATA BP102 (8-1/2 TON) HP W/O PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 19
14 ELECTRICAL DATA BP102 (8-1/2 TON) HP WITH PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 19
15 ELECTRICAL DATA BP120 (10 TON) HP W/O PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 20
16 ELECTRICAL DATA BP120 (10 TON) HP WITH PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 20
17 ELECTRICAL DATA BP150 (12-1/2 TON) HP W/O PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 21
18 ELECTRICAL DATA BP150 (12-1/2 TON) HP W/PWRD
CONVENIENCE OUTLET . . . . . . . . . . . . . . . . . . . . . . . . 21
19 PHYSICAL DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20 ELECTRIC HEAT MINIMUM SUPPLY AIR. . . . . . . . . . . 22
21 SUPPLY AIR LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . 25
22 6-1/2 TON STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 26
23 6-1/2 TON OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 26
24 7-1/2 TON STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 27
25 7-1/2 TON OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 28
26 8-1/2 TON STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 29
27 8-1/2 TON OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . 29
Tbl. # Pg. #
28 10 TON STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .29
29 10 TON OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .30
30 12-1/2 TON STANDARD MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .30
31 12-1/2 TON OPTIONAL MOTOR DOWN SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .30
32 6-1/2 TON STANDARD MOTOR SIDE SHOT
BLOWER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .31
33 6-1/2 TON OPTIONAL MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
34 7-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
35 7-1/2 TON OPTIONAL MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
36 8-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
37 8-1/2 TON OPTIONAL MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
38 10 TON STANDARD MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
39 10 TON OPTIONAL MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
40 12-1/2 TON STANDARD MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
41 12-1/2 TON OPTIONAL MOTOR SIDE SHOT BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
42 INDOOR BLOWER SPECIFICATIONS. . . . . . . . . . . . . . .36
43 POWER EXHAUST SPECIFICATIONS . . . . . . . . . . . . . .36
44 ADDITIONAL STATIC RESISTANCE 50” CABINET . . . .40
45 ADDITIONAL STATIC RESISTANCE 42" CABINET . . . .40
46 MOTOR SHEAVE DATUM DIAMETERS . . . . . . . . . . . . .41
47 ELECTRIC HEAT LIMIT SETTING 50” CABINET. . . . . . .44
48 ELECTRIC HEAT LIMIT SETTING 42” CABINET. . . . . . .44
49 ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . . . . .45
50 SUPERHEAT CHARGING . . . . . . . . . . . . . . . . . . . . . . . .46
51 COOLING SUPERHEAT 6-1/2 TON HEAT PUMP. . . . . .46
52 COOLING SUPERHEAT 7-1/2 TON HEAT PUMP. . . . . .47
53 COOLING SUPERHEAT 8-1/2 & 10 TON HEAT PUMP. .47
54 COOLING SUPERHEAT 12.5 TON HEAT PUMP . . . . . .48
55 UNIT CONTROL BOARD FLASH CODES . . . . . . . . . . . .49

127421-YIM-C-0606
Unitary Products Group 5
GENERAL
YORK®Predator®Heat Pump units are single package,
reverse cycle air conditioners designed for outdoor installa-
tion on a rooftop or slab and for non-residential use. These
units can be equipped with factory or field installed electric
heaters for heating applications.
These units are completely assembled on rigid, permanently
attached base rails. All piping, refrigerant charge, and electri-
cal wiring is factory installed and tested. The units require
electric power and duct connections. The electric heaters
have nickel-chrome elements and utilize single-point power
connection.
SAFETY CONSIDERATIONS
Due to system pressure, moving parts, and electrical compo-
nents, installation and servicing of air conditioning equipment
can be hazardous. Only qualified, trained service personnel
should install, repair, or service this equipment. Untrained
personnel can perform basic maintenance functions of clean-
ing coils and filters and replacing filters.
Observe all precautions in the literature, labels, and tags
accompanying the equipment whenever working on air condi-
tioning equipment. Be sure to follow all other applicable
safety precautions and codes including National Electric
Code, ANSI/NFPA No. 70 - latest edition U.S.A. and Cana-
dian Electric Code, CSA C22.1 in Canada.
Wear safety glasses and work gloves. Use quenching cloth
and have a fire extinguisher available during brazing opera-
tions.
INSPECTION
As soon as a unit is received, it should be inspected for possi-
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier’s freight bill. A
separate request for inspection by the carrier’s agent should
be made in writing.
REFERENCE
Additional information is available in the following reference
forms:
• Technical Guide - 259337
• General Installation - 127421
• Pre-start & Post-start Check List
• Economizer Accessory -
Downflow Factory Installed
Downflow Field Installed
Horizontal Field Installed
• Motorized Outdoor Air Damper
• Manual Outdoor Air Damper (0-100%)
• Manual Outdoor Air Damper (0-35%)
• Electric Heater Accessory 50” Cabinet
• Electric Heater Accessory 42” Cabinet
RENEWAL PARTS
Contact your local York® parts distribution center for autho-
rized replacement parts.
APPROVALS
Design certified by CSA as follows:
1. For use as a cooling only unit, cooling unit with supple-
mental electric heat forced air furnace.
2. For outdoor installation only.
3. For installation on combustible material and may be
installed directly on combustible flooring or, in the U.S.,
on wood flooring or Class A, Class B or Class C roof cov-
ering materials.
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. NOTES are intended to
clarify or make the installation easier. CAUTIONS are given
to prevent equipment damage. WARNINGS are given to alert
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly.
This furnace is not to be used for temporary heating
of buildings or structures under construction.
Before performing service or maintenance opera-
tions on unit, turn off main power switch to unit. Elec-
trical shock could cause personal injury. Improper
installation, adjustment, alteration, service or main-
tenance can cause injury or property damage. Refer
to this manual. For assistance or additional informa-
tion consult a qualified installer, service agency or
the gas supplier.
This product must be installed in strict compliance with
the enclosed installation instructions and any applica-
ble local, state, and national codes including, but not
limited to, building, electrical, and mechanical codes.
Incorrect installation may create a condition where the
operation of the product could cause personal injury
or property damage.

127421-YIM-C-0606
6Unitary Products Group
NOMENCLATURE
B P 090 C00 A 2 A AA 3 0 1 2 4 A
Product Category
B = HP, Single Pkg., R-22
A = Std. Motor
Airflow
B = Std. Motor/Econo./Barometric Relief (Downflow
Only)
C = Std. Motor/Econo./Power Exhaust (Downflow Only)
D = Std. Motor/Motorized Damper (Downflow Only)
E = Std. Motor/Horizontal Economizer (No Baro.)
F = Std. Motor/Slab Econo./Power Exhaust
(Downflow Only)
G = Std. Motor/Slab Econo./Barometric Relief
(Downflow Only)
N = Hi Static Mtr.
P = Hi Static Mtr./Econo./Barometric Relief
(Downflow Only)
Q = Hi Static Mtr./Econo./Power Exhaust
(Downflow Only)
R = Hi Static Mtr./Motorized Damper (Downflow Only)
S = Hi Static Mtr./Horizontal Economizer (No Baro.)
T = Hi Static Mtr./Slab Econo./Power Exhaust
(Downflow Only)
U = Hi Static Mtr./Slab Econo./Barometric Relief
(Downflow only)
3 = Third Generation
Product Generation
4 = Fourth Generation
C00 = Cooling Only. No heat installed
Heat Type and Nominal Heat Capacity
E09 = 9 KW
E18 = 18 KW
E24 = 24 KW
E36 = 36 KW
E54 = 54 KW
Electric Heat Options
078 = 6.5 Ton
Nominal Cooling Capacity
090 = 7.5 Ton
102 = 8.5 Ton
120 = 10.0 Ton
150 = 12.5 Ton
Product Identifier
P = 9.3-10.6 EER HP
Voltage
2 = 208/230-3-60
4 = 460-3-60
5 = 575-3-60
Product Style
A = Style A
B = Style B
C = Style C
A = No Options Installed
Installation Options
B=Option1
C=Option2
D = Options 1 & 2
E=Option3
F = Option 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2, & 4
L = Options 1,3 & 4
M=Options1,2,3,&4
N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3, & 4
R = Options 3 & 4
S=Option5
T = Options 1 & 5
U = Options 1, 3, & 5
V = Options 1, 4, & 5
W = Options 1, 3, 4, & 5
X = Options 3 & 5
Y = Options 4 & 5
Z = Options 3, 4 & 5
1 = Disconnect
2 = Non-Pwr'd Conv. Outlet
3 = Smoke Detector S.A.
4 = Smoke Detector R.A.
5=Pwr'dConv.Outlet
Options
SS Drain Pan
Configuration Options (not required for all units)
These four digits will not be assigned until a quote is requested, or an order placed.
CPC Controller, DFS, APS
Johnson Controller, DFS, APS
Honeywell Controller, DFS, APS
Novar Controller, DFS, APS
Simplicity IntelliComfort Controller
Simplicity IntelliComfort Controller w/ModLinc
2" Pleated filters
BAS Ready Unit with Belimo Economizer
Shipping Bag
Any Combination of Additional Options that Don’t Have an Option Code Pre-assigned
AA = None
AB = Phase Monitor
AC = Coil Guard
AD = Dirty Filter Switch
AE = Phase Monitor & Coil Guard
AF = Phase Monitor & Dirty Filter Switch
AG = Coil Guard & Dirty Filter Switch
AH = Phase Monitor, Coil Guard & Dirty Filter Switch
Additional Options
RC = Coil Guard, Shipping Bag & American Flag
TA = Technicoat Condenser Coil
TJ = Technicoat Evaporator Coil
TS = Technicoat Evaporator & Condenser Coils
6.5-12.5 Ton York®Model Number Nomenclature
ZZ = If desired option combination is not listed above, ZZ will be assigned and configuration options will be
located in digits 15-18.

127421-YIM-C-0606
Unitary Products Group 7
INSTALLATION
INSTALLATION SAFETY INFORMATION
Read these instructions before continuing this appliance
installation. This is an outdoor combination heating and cool-
ing unit. The installer must assure that these instructions are
made available to the consumer and with instructions to
retain them for future reference.
1. This equipment is not to be used for temporary heating
of buildings or structures under construction.
PRECEDING INSTALLATION
1. Remove the two screws holding the brackets in the front,
rear and compressor side fork-lift slots.
2. Turn each bracket toward the ground and the protective
plywood covering will drop to the ground.
3. Remove the condenser coil external protective covering
prior to operation.
4. Remove the toolless doorknobs and instruction packet
prior to installation.
LIMITATIONS
These units must be installed in accordance with the following:
In U.S.A.:
1. National Electrical Code, ANSI/NFPA No. 70 - Latest
Edition
2. Local building codes
3. Local electric utility requirements
In Canada:
1. Canadian Electrical Code, CSA C22.1
2. Installation Codes, CSA - B149.1.
3. Local plumbing and waste water codes, and
4. Other applicable local codes.
Refer to Tables 1 & 2 for unit application data.
If components are to be added to a unit to meet local codes,
they are to be installed at the dealer’s and/or customer’s
expense.
Size of unit for proposed installation should be based on heat
loss/heat gain calculation made according to the methods of
Air Conditioning Contractors of America (ACCA).
This furnace is not to be used for temporary heating of build-
ings or structures under construction.
FIGURE 1 - UNIT SHIPPING BRACKET
FIGURE 2 - CONDENSER COIL COVERING
This product must be installed in strict compliance
with the enclosed installation instructions and any
applicable local, state and national codes including,
but not limited to, building, electrical, and mechani-
cal codes.
Bracket
Screws Turn down
Condenser
Coil External
Protective
Covering
Barometric
Relief Hood in
Shipping Loca-
tion (if included)
FIGURE 3 - COMPRESSOR SECTION
Toolless
Doorknobs
Installation
Instruction

127421-YIM-C-0606
8Unitary Products Group
LOCATION
Use the following guidelines to select a suitable location for
these units:
1. Unit is designed for outdoor installation only.
2. Condenser coils must have an unlimited supply of air.
Where a choice of location is possible, position the unit
on either north or east side of building.
3. Suitable for mounting on roof curb.
4. For ground level installation, use a level concrete slab
with a minimum thickness of 4 inches. The length and
width should be at least 6 inches greater than the unit
base rails. Do not tie slab to the building foundation.
5. Roof structures must be able to support the weight of the
unit and its options/accessories. Unit must be installed
on a solid, level roof curb or appropriate angle iron
frame.
6. Maintain level tolerance to 1/2” across the entire width
and length of unit.
FIGURE 4 - PREDATOR®COMPONENT LOCATION
Slide-Out Drain Pan
w/ Steel 3/4” NPT,
Female Connection
Power Ventor Motor
Compressor #1 Access (High-Eff
Compressor w/ crankcase heater)
Belt-Drive
Blower
Motor
Terminal Block
for Hi-Voltage
Connection
Disconnect Location
(Optional Disconnect Switch) Filter Access
(2” Filters) Filter-Drier (Solid Core)
Condenser
Section
Two-stage gas heat-
ing to maintain
warm, comfortable
temperature
Intelligent control board for
safe and efficient operation
Side entry power
and control wiring
knockouts
Toolless
door latch
Base Rails w/ Forklift
Slots (3 Sides) & Lift-
ing Holes
Second model
nameplate inside
hinged access
panel
Compressor #2
Access (High-
Eff Compressor
w/ crankcase
heater)
Roof curbs in eight- and
fourteen-inch heights.
Rood curbs for transition-
ing frrm Sunline footprint
to the DM/DH/DF Series
footprint are also avail-
able (field-installed
accessory)
Dual stage
cooling for
maximum
comfort Slide-out motor
and blower
assembly for
ease of adjust-
ment and ser-
vice
Simplicity™ControlBoard
w/Screw Connector for
T-stat Wiring and Network
Connection
TABLE 1: UNIT VOLTAGE LIMITATIONS
Power Rating*
*. Utilization range “A” in accordance with ARI Standard 110.
Minimum Maximum
208/230-3-60 187 252
460-3-60 432 504
575-3-60 540 630
380/415-3-50 342 456
TABLE 2: UNIT TEMPERATURE LIMITATIONS
Temperature Min. Max.
Wet Bulb Temperature (°F) of Air on
Evaporator Coil 57 72
Dry Bulb Temperature (°F) of Air on
Condenser Coil 0*
*. A low ambient accessory is available for operation
down to -20°F.
125

127421-YIM-C-0606
Unitary Products Group 9
RIGGING AND HANDLING
Exercise care when moving the unit. Do not remove any
packaging until the unit is near the place of installation. Rig
the unit by attaching chain or cable slings to the lifting holes
provided in the base rails. Spreader bars, whose length
exceeds the largest dimension across the unit, MUST be
used across the top of the unit.
Units may be moved or lifted with a forklift. Slotted openings
in the base rails are provided for this purpose.
LENGTH OF FORKS MUST BE A MINIMUM OF 60
INCHES.
If a unit is to be installed on a roof curb other than a
YORK roof curb, gasketing must be applied to all
surfaces that come in contact with the unit under-
side.
Before lifting, make sure the unit weight is distrib-
uted equally on the rigging cables so it will lift evenly.
All panels must be secured in place when the unit is
lifted.
The condenser coils should be protected from rig-
ging cable damage with plywood or other suitable
material.
FIGURE 5 - UNIT 4 POINT LOAD
D
A
CB
L E F T
F R O N T
TABLE 3: UNIT WEIGHTS
Model Shipping Weight (lb.) Operating Weight (lb.)
BP078 1104 1099
BP090 895 890
BP102 1178 1173
BP120 1212 1207
BP150 1202 1197
Econ. 85 84
w/ PE 150 148
Elec. Heat*49 49
*. 54kW heater.
TABLE 4: 4 POINT LOAD WEIGHT
Model Location (lbs.)
ABCD
BP078 241 206 300 352
BP090 199 148 232 311
BP102 257 220 321 375
BP120 265 226 330 386
BP150 263 224 327 383
TABLE 5: 6 POINT LOAD WEIGHT
Model Location (lbs.)
ABCDEF
BP078 165 148 134 195 216 241
BP090 139 113 94 147 128 218
BP102 176 158 143 208 231 257
BP120 181 163 147 214 237 264
BP150 180 161 146 213 235 262
FIGURE 6 - UNIT 6 POINT LOAD
D
A
C
B
E
F
L E F T
F R O N T

127421-YIM-C-0606
10 Unitary Products Group
FIGURE 7 - UNIT CENTER OF GRAVITY
CLEARANCES
All units require particular clearances for proper operation
and service. Refer to Table 7 for clearances required for con-
struction, servicing, and proper unit operation.
Unit Model Number XY
BP078 47 1/2 25 1/2
BP090 38 23
BP102 47 1/2 25 1/2
BP120 47 1/2 25 1/2
BP150 47 1/2 25 1/2
XY
LEFT FRONT
Do not permit overhanging structures or shrubs to
obstruct condenser air discharge outlet, combustion
air inlet or vent outlets.
FIGURE 8 - UNIT DIMENSIONS
)RU%DVHUDLO
'LPHQVLRQV
6HH'HWDLO$








&RQYHQLHQFH
3RZHU
2XWOHW
(QWU\

3RZHU
(QWU\


&RQWURO
(QWU\

3RZHU
(QWU\

/()7
)5217
)RU'UDLQ
'LPHQVLRQV
6HH'HWDLO%
;
TABLE 6: UNIT HEIGHT
Unit Model Number X
BP078 50 3/4
BP090 42
BP102 50 3/4
BP120 50 3/4
BP150 50 3/4
TABLE 7: UNIT CLEARANCES
Top*
*. Units must be installed outdoors. Overhanging struc-
ture or shrubs should not obstruct condenser air dis-
charge outlet.
72” Right 12”
Front 36” Left 36”
Rear†
†. To remove the slide-out drain pan, a rear clearance of
sixty inches is required. If space is unavailable, the
drain pan can be removed through the front by separat-
ing the corner wall.
36” Bottom‡
‡. Units may be installed on combustible floors made from
wood or class A, B or C roof covering materials.
0”

127421-YIM-C-0606
Unitary Products Group 11
NOTE: A one-inch clearance must be provided between
any combustible material and the supply ductwork
for a distance of 3 feet from the unit.
5 - 1 / 4 B a s e
P a n
1 7 - 1 3 / 1 6
V i e w o f a l l A c r o s s f r o m C o i l
G a s P i p e I n l e t
DETAIL A
3 - 3 / 4
3 - 9 / 1 6
2 - 3 / 8
DETAIL
B
5 - 3 / 8
DETAIL C
FIGURE 9 - BOTTOM DUCT OPENINGS (FROM ABOVE)
3 2 - 1 1 / 1 6
6 - 1 3 / 1 6
6 - 1 3 / 1 6
2 7 - 1 / 2
1 8
2 1 - 3 / 1 6
1 9 - 3 / 1 6
1 7 - 3 / 1 6
1 4 - 2 3 / 3 2
1 6 - 3 / 8
1 8 - 1 / 1 6
6 - 1 3 / 1 6
2 4
2 1
L E F T
B o t t o m P o w e r ,
C o n t r o l a n d
C o n v e n i e n c e
O u t l e t i r i n g
E n t r y
S U P P L Y
A I R
R E T U R N
A I R
F R O N T
1 9 - 5 / 8
7 - 1 / 8
B o t t o m C o n d e n s a t e
L o c a t i o n

127421-YIM-C-0606
12 Unitary Products Group
DUCTWORK
Ductwork should be designed and sized according to the
methods in Manual D of the Air Conditioning Contractors of
America (ACCA) or as recommended by any other recog-
nized authority such as ASHRAE or SMACNA.
A closed return duct system should be used. This will not
preclude use of economizers or outdoor fresh air intake. The
supply and return air duct connections at the unit should be
made with flexible joints to minimize noise.
The supply and return air duct systems should be designed
for the CFM and static pressure requirements of the job. They
should NOT be sized to match the dimensions of the duct
connections on the unit.
Refer to Figure 9 for bottom air duct openings. Refer to Fig-
ure 10 for rear air duct openings.
DUCT COVERS
Units are shipped with the side duct openings covered and a
covering over the bottom of the unit. For bottom duct applica-
tion, no duct cover changes are necessary. For side duct
application, remove the side duct covers and install over the
bottom duct openings. The panels removed from the side
duct connections are designed to be reused by securing each
panel to its respective downflow opening. But keep in mind
that the supply panel is installed with the painted surface UP,
facing the heat exchanger, while the return panel is installed
with the painted surface DOWN, facing the downflow duct
opening. The supply panel is secured with the bracket
(already in place from the factory) and two screws. It’s a snug
fit for the panel when sliding it between the heat exchanger
and unit bottom, but there is room. The return panel is
secured with four screws.
FIGURE 10 - REAR DUCT DIMENSIONS
18-1/4
5-5/32
31-11/16
2-31/32
18-1/4
Return
Air
Supply
Air
Patch Plate
For Slide-Out
Drain Pan
Dot Plugs
C
A
B
REAR DUCT DIMENSIONS
CABINET SIZE DIMENSION
“A” “B” “C”
50 3/4” 28 1/4 18 1/16 28 1/4
42” 27 3/4 12 1/16 27 1/2

127421-YIM-C-0606
Unitary Products Group 13
Note orientation. Panel is “insulation” side up.
FIGURE 11 - PREDATOR®ROOF CURB DIMENSIONS
FIGURE 12 - SUNLINE™ TO PREDATOR®TRANSITION ROOF CURBS
8 o r 1 4
5 0 - 1 / 2
3 0
2 0
2 0
8 0 - 5 / 8
6
2 T Y P .
I N S U L A T E D D E C K U N D E R
C O M P R E S S O R S E C T I O N
I N S U L A T E D D E C K U N D E R
C O N D E N S E R S E C T I O N
F R O N T
R I G H T
S U P P L Y
R E T U R N
7 6 - 5 / 8
9 4
5 0 - 1 / 2 3 0 - 1 / 2
6 4 - 1 / 4
5 9 - 1 / 4
1 0
2 3 4
2 6 8 0 - 5 / 8
2 T Y P
F R O N T R I G H T
S U P P L Y
R E T U R N
When fastening ductwork to side duct flanges on
unit, insert screws through duct flanges only. DO
NOT insert screws through casing. Outdoor duct-
work must be insulated and water-proofed.
FIGURE 13 - SIDE PANELS WITH HOLE PLUGS

127421-YIM-C-0606
14 Unitary Products Group
CONDENSATE DRAIN
The side condensate drain is reversible and maybe re-ori-
ented to the rear of the cabinet to facilitate condensate pip-
ing. A condensate drain connection is available through the
base pan for piping inside the roof curb. Trap the connection
per Figure 16. The trap and drain lines should be protected
from freezing.
Plumbing must conform to local codes. Use a sealing com-
pound on male pipe threads. Install condensate drain line
from the 3/4 inch NPT female connection on the unit to an
open drain.
COMPRESSORS
The compressors are mounted on elastomer insulators. The
mounting bolts have been fully tightened for shipping.
FILTERS
Two-inch filters are supplied with each unit. One-inch filters
may be used with no modification to the filter racks. Filters
must always be installed ahead of evaporator coil and must
be kept clean or replaced with same size and type. Dirty fil-
ters reduce the capacity of the unit and result in frosted coils
or safety shutdown. All units use four filters. Refer to Physical
Data table for the number and size of filters needed for the
unit. The unit should not be operated without filters properly
installed.
THERMOSTAT WIRING
The thermostat should be located on an inside wall approxi-
mately 56 inches above the floor where it will not be subject
to drafts, sun exposure or heat from electrical fixtures or
appliances. Follow the manufacturer's instructions enclosed
with thermostat for general installation procedure. Seven (7)
color-coded, insulated wires should be used to connect the
thermostat to the unit. Refer to Table 8 for control wire sizing
and maximum length.
POWER AND CONTROL WIRING
Field wiring to the unit, fuses, and disconnects must conform
to provisions of National Electrical Code (NEC), ANSI/NFPA
No. 70 – Latest Edition (in U.S.A.), current Canadian Electri-
cal Code CSA C22.1, and/or local ordinances. The unit must
be electrically grounded in accordance with NEC and CEC as
specified above and/or local codes.
Voltage tolerances which must be maintained at the com-
pressor terminals during starting and running conditions are
indicated on the unit Rating Plate and Table 1.
FIGURE 14 - RETURN DOWNFLOWPLENUM WITH
PANEL
FIGURE 15 - DISCHARGE PANEL IN PLACE
FIGURE 16 - CONDENSATE DRAIN
O P T I O N A L C O I L
G U A R D
3 " M i n i m u m
Do not loosen the compressor mounting bolts.
Make sure that panel latches are properly positioned
on the unit to maintain an airtight seal.
TABLE 8: CONTROL WIRE SIZES
Wire Size Maximum Length*
*. From the unit to the thermostat and back to the unit.
18 AWG 150 Feet

127421-YIM-C-0606
Unitary Products Group 15
The internal wiring harnesses furnished with this unit are an
integral part of the design certified unit. Field alteration to
comply with electrical codes should not be required. If any of
the wire supplied with the unit must be replaced, replacement
wire must be of the type shown on the wiring diagram and the
same minimum gauge as the replaced wire.
A disconnect must be utilized for these units. Factory
installed disconnects are available. If installing a disconnect
(field supplied or York International®supplied accessory),
refer to Figure 3 for the recommended mounting location.
NOTE: Since not all local codes allow the mounting of a dis-
connect on the unit, please confirm compliance with
local code before mounting a disconnect on the unit.
Electrical line must be sized properly to carry the load. USE
COPPER CONDUCTORS ONLY. Each unit must be wired
with a separate branch circuit fed directly from the meter
panel and properly fused.
Refer to Figures 17, 18 and 19 for typical field wiring and to
the appropriate unit wiring diagram mounted inside control
doors for control circuit and power wiring information.
POWER WIRING DETAIL
Units are factory wired for the voltage shown on the unit
nameplate. Refer to Electrical Data Tables 9 through 18 size
power wiring, fuses, and disconnect switch.
NOTE: This unit does not require a heat pump thermostat.
It is designed to work with a standard two-stage
cool, two-stage heat thermostat; however, the ther-
mostat must provide a “G” signal when there is a
call for “W1”.
Avoid damage to internal components if drilling
holes for disconnect mounting.
When connecting electrical power and control wiring
to the unit, water-proof connectors must be used so
that water or moisture cannot be drawn into the unit
during normal operation. The above water-proofing
conditions will also apply when installing a field sup-
plied disconnect switch.
FIGURE 17 - ELECTRONIC THERMOSTAT FIELD WIRING
2
R C
R H
Y 1
Y 2
1
G
C
X 1
X 3
X 4
A 1
A 2
T
T
2
Y 1
Y 2
1
G
C
O C C
X
R
T H E R M O S T A T
1
T E R M I N A L S U N I T T E R M I N A L S
S T R I P T B 1
1
E l e c t r o n i c p r o g r a m m a b l e T h e r m o s t a t 2 E T 0 7 7 0 0 1 0 0 2 4 ( i n c l u d e s s u b b a s e ) .
2
T e r m i n a l s A 1 a n d A 2 p r o v i d e a r e l a y o u t p u t t o c l o s e t h e o u t d o o r
e c o n o m i z e r d a m p e r s w h e n t h e t h e r m o s t a t s w i t c h e s t o t h e s e t - b a c k p o s i t i o n .
2 4 V o l t
T r a n s f o r m e r
2
T O R E M O T E S E N S O R
2 E T 0 4 7 0 1 3 2 4 I F U S E D
The thermostat must provide a “G” signal
when there is a call for “W1.” The unit con-
trol board will energize the indoor blower
when the compressors are energized; how-
ever, if the thermostat calls for “W2” during
the anti-short-cycle delay, the electric heat
(when installed) will be energized immedi-
ately upon the call for “W2.”

127421-YIM-C-0606
16 Unitary Products Group
FIGURE 18 - FIELD WIRING 24 VOLT THERMOSTAT
O C C
1
2
Y 1
G
Y 2
X
R
S D
C
R E M O T E M I N P O S
1
2
Y 1
G
Y 2
C
U N I T C O N T R O L
B O A R D
T - S T A T
R H
R C
The thermostat must provide a “G” signal
when there is a call for “W1.”The unit control
board will energize the indoor blower when
the compressors are energized; however, if
the thermostat calls for “W2” during the anti-
short-cycle delay, the electric heat (when
installed) will be energized immediately
upon the call for “W2.”
FIGURE 19 - FIELD WIRING DISCONNECT
  







  
 

127421-YIM-C-0606
Unitary Products Group 17
TABLE 9: ELECTRICAL DATA BP078 (6-1/2 TON) HP W/O PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
1.5 2 1.5 2 1.5 2 1.5 2 1.5 2
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 33.0 35.0 38.5 40.5 45 45 50 50
2TP04520925 6.8 18.9 56.6 58.6 62.1 64.1 70 70 70 70
2TP04521825 13.5 37.5 79.9 81.9 85.4 87.4 80 90 90 90
2TP04522425 18.0 50.0 95.5 97.5 101.0 103.0 100 100 110 110
2TP04523625 25.5 70.8 121.5 123.5 127.0 129.0 125 125 150 150
None -- -- 33.0 35.0 38.5 40.5 45 45 50 50
2TP04520925 9.0 21.7 60.1 62.1 65.6 67.6 70 70 70 80
2TP04521825 18.0 43.3 87.2 89.2 92.7 94.7 90 90 100 100
2TP04522425 24.0 57.7 105.2 107.2 110.7 112.7 110 110 125 125
2TP04523625 34.0 81.8 135.3 137.3 140.8 142.8 150 150 150 150
None -- -- 16.6 17.6 18.8 19.8 25 25 25 25
2TP04520946 9 11.3 30.1 31.1 32.3 33.3 35 35 35 40
2TP04521846 18 22.6 43.6 44.6 45.8 46.8 45 45 50 50
2TP04522446 24 30.1 52.7 53.7 54.9 55.9 60 60 60 60
2TP04523646 34 42.7 67.7 68.7 69.9 70.9 70 70 70 80
None -- -- 13.1 14.3 14.9 16.1 20 20 20 20
2TP04520958 9 9.0 23.9 25.1 25.7 26.9 25 30 30 30
2TP04521858 18 18.1 34.8 36 36.6 37.8 35 40 40 40
2TP04522458 24 24.1 42 43.2 43.8 45 45 45 45 45
2TP04523658 34 34.1 54 55.2 55.8 57 60 60 60 60
*
0.0
7.6 58.4 0.6 2.4 3.6 1.8 0.0
73.0 0.8 3.1 4.1
5.56.2 8.2
2.2
0.0
18.9 146.0 1.6 6.2 8.2 5.5 0.0
146.0 1.6
Maximum HACR breaker of the same AMP size is applicable.
460
575
9.5
208
230
18.9
Max Fuse* Size
w/Power
Exhaust
(Amps)
FLA FLA
Actual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric Heater
Model No.
Max
Fuse*
Size
(Amps)
Voltage
Compressors OD Fan
Motors
Supply
Blower
Motor FLA
TABLE 10: ELECTRICAL DATA BP078 (6-1/2 TON) HP WITH PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
1.5 2 1.5 2 1.5 2 1.5 2 1.5 2
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 43.0 45.0 48.5 50.5 60 60 60 60
2TP04520925 6.8 18.9 66.6 68.6 72.1 74.1 80 80 80 80
2TP04521825 13.5 37.5 89.9 91.9 95.4 97.4 90 100 100 100
2TP04522425 18.0 50.0 105.5 107.5 111.0 113.0 110 110 125 125
2TP04523625 25.5 70.8 131.5 133.5 137.0 139.0 150 150 150 150
None -- -- 43.0 45.0 48.5 50.5 60 60 60 60
2TP04520925 9.0 21.7 70.1 72.1 75.6 77.6 80 80 80 90
2TP04521825 18.0 43.3 97.2 99.2 102.7 104.7 100 100 110 110
2TP04522425 24.0 57.7 115.2 117.2 120.7 122.7 125 125 125 125
2TP04523625 34.0 81.8 145.3 147.3 150.8 152.8 150 150 175 175
None -- -- 21.6 22.6 23.8 24.8 30 30 30 30
2TP04520946 9 11.3 35.1 36.1 37.3 38.3 40 40 40 45
2TP04521846 18 22.6 48.6 49.6 50.8 51.8 50 50 60 60
2TP04522446 24 30.1 57.7 58.7 59.9 60.9 60 60 60 70
2TP04523646 34 42.7 72.7 73.7 74.9 75.9 80 80 80 80
None -- -- 17.1 18.3 18.9 20.1 20 25 25 25
2TP04520958 9 9.0 27.9 29.1 29.7 30.9 30 30 35 35
2TP04521858 18 18.1 38.8 40 40.6 41.8 40 40 45 45
2TP04522458 24 24.1 46 47.2 47.8 49 50 50 50 50
2TP04523658 34 34.1 58 59.2 59.8 61 60 60 60 70
*
4.0
4.1
Maximum HACR breaker of the same AMP size is applicable.
2.2 5.0
7.6 58.4 0.6 2.4 3.6 1.8
10.0
18.9 146.0 1.6 6.2 8.2 5.5 10.0
9.5
Electric Heater
Model No.
A
ctual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
575
OD Fan
Motors
Supply
Blower
Motor FLA
Pwr
Exh
Motor
FLA
8.2 5.5
73.0 0.8 3.1
Voltage
Compressors
208
460
230
146.0 1.6 6.218.9
Pwr
Conv
Outlet
MCA
w/Power
Exhaust
(Amps)
Max
Fuse*
Size
(Amps)
Max Fuse* Size
w/Power
Exhaust
(Amps)
FLA

127421-YIM-C-0606
18 Unitary Products Group
TABLE 11: ELECTRICAL DATA BP090 (7-1/2 TON) HP W/O PWRD CONVENIENCE OUTLET
RLA LRA FLA
ea. ea. ea.
None -- -- 37.1 39.8 42.6 45.3 45 50 50 50
2TP04540925 6.8 18.9 60.7 63.4 66.2 68.9 70 70 70 70
2TP04541825 13.5 37.5 83.9 86.6 89.4 92.1 90 90 90 100
2TP04542425 18 50.0 99.5 102.2 105.0 107.7 100 110 110 110
2TP04543625 25.5 70.8 125.6 128.3 131.1 133.8 150 150 150 150
None -- -- 37.1 39.8 42.6 45.3 45 50 50 50
2TP04540925 9 21.7 64.1 66.8 69.6 72.3 70 70 70 80
2TP04541825 18 43.3 91.2 93.9 96.7 99.4 100 100 100 100
2TP04542425 24 57.7 109.2 111.9 114.7 117.4 110 125 125 125
2TP04543625 34 81.8 139.3 142.0 144.8 147.5 150 150 150 150
None -- -- 20.1 21.3 22.3 23.5 25 25 25 25
2TP04540946 9 11.3 33.6 34.8 35.8 37 35 35 40 40
2TP04541846 18 22.6 47.2 48.4 49.4 50.6 50 50 50 60
2TP04542446 24 30.1 56.2 57.4 58.4 59.6 60 60 60 60
2TP04543646 34 42.7 71.2 72.4 73.4 74.6 80 80 80 80
None -- -- 16.3 16.8 18.1 18.6 20 20 20 20
2TP04540958 9 9.0 27.1 27.6 28.9 29.4 30 30 30 30
2TP04541858 18 18.1 37.9 38.4 39.7 40.2 40 40 40 45
2TP04542458 24 24.1 45.1 45.6 46.9 47.4 50 50 50 50
2TP04543658 34 34.1 57.2 57.7 59 59.5 60 60 60 60
11.5 84.0
575
0.01.5 8.2 10.9 5.5
11.5 84.0 1.5
208
460
230
2 HP 3 HP 2 HP 3 HP
Max Fuse*
Size
(Amps)
Max Fuse
Size
w/Power
Exhaust
2 HP 3 HP FLA FLA 2 HP 3 HP 2 HP 3 HP
Actual
KW Heater Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Supply
Blower
Motor FLA
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric
Heater Model
No.
Voltage Compressors OD Fan
Motors
8.2 10.9 5.5 0.0
6.4 42.0 0.8 4.1 5.3 2.2 0.0
5.1 34.0 0.6 3.6 4.1 1.8 0.0
TABLE 12: ELECTRICAL DATA BP090 (7-1/2 TON) HP WITH PWRD CONVENIENCE OUTLET
RLA LRA FLA
ea. ea. ea.
None -- -- 47.1 49.8 52.6 55.3 50 60 60 60
2TP04540925 6.8 18.9 70.7 73.4 76.2 78.9 80 80 80 80
2TP04541825 13.5 37.5 93.9 96.6 99.4 102.1 100 100 100 110
2TP04542425 18 50.0 109.5 112.2 115.0 117.7 110 125 125 125
2TP04543625 25.5 70.8 135.6 138.3 141.1 143.8 150 150 150 150
None -- -- 47.1 49.8 52.6 55.3 50 60 60 60
2TP04540925 9 21.7 74.1 76.8 79.6 82.3 80 80 80 90
2TP04541825 18 43.3 101.2 103.9 106.7 109.4 110 110 110 110
2TP04542425 24 57.7 119.2 121.9 124.7 127.4 125 125 125 150
2TP04543625 34 81.8 149.3 152.0 154.8 157.5 150 175 175 175
None -- -- 25.1 26.3 27.3 28.5 30 30 30 30
2TP04540946 9 11.3 38.6 39.8 40.8 42 40 40 45 45
2TP04541846 18 22.6 52.2 53.4 54.4 55.6 60 60 60 60
2TP04542446 24 30.1 61.2 62.4 63.4 64.6 70 70 70 70
2TP04543646 34 42.7 76.2 77.4 78.4 79.6 80 80 80 80
None -- -- 20.3 20.8 22.1 22.6 25 25 25 25
2TP04540958 9 9.0 31.1 31.6 32.9 33.4 35 35 35 35
2TP04541858 18 18.1 41.9 42.4 43.7 44.2 45 45 45 45
2TP04542458 24 24.1 49.1 49.6 50.9 51.4 50 50 60 60
2TP04543658 34 34.1 61.2 61.7 63 63.5 70 70 70 70
575
208
460
230
Voltage Compressors
2 HP 3 HP 2 HP 3 HP
Max Fuse*
Size
(Amps)
Max Fuse
Size
w/Power
Exhaust
2 HP 3 HP FLA FLA 2 HP 3 HP 2 HP 3 HP
Actual
KW Heater Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Supply
Blower
Motor FLA
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric
Heater Model
No.
OD Fan
Motors
11.5 84.0 1.5 8.2 10.9 5.5 10.0
11.5 84.0 1.5 8.2 10.9 5.5 10.0
6.4 42.0 0.8 4.1 5.3 2.2 5.0
5.1 34.0 0.6 3.6 4.1 1.8 4.0

127421-YIM-C-0606
Unitary Products Group 19
TABLE 13: ELECTRICAL DATA BP102 (8-1/2 TON) HP W/O PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
23 2 3 2 3232 3
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 48.3 51.0 53.8 56.5 60 60 60 70
2TP04520925 6.8 18.9 71.9 74.6 77.4 80.1 80 80 80 90
2TP04521825 13.5 37.5 95.1 97.8 100.6 103.3 100 100 110 110
2TP04522425 18.0 50.0 110.7 113.4 116.2 118.9 125 125 125 125
2TP04523625 25.5 70.8 136.8 139.5 142.3 145.0 150 150 150 150
None -- -- 48.3 51.0 53.8 56.5 60 60 60 70
2TP04520925 9.0 21.7 75.3 78.0 80.8 83.5 80 80 90 90
2TP04521825 18.0 43.3 102.4 105.1 107.9 110.6 110 110 110 125
2TP04522425 24.0 57.7 120.4 123.1 125.9 128.6 125 125 150 150
2TP04523625 34.0 81.8 150.5 153.2 156.0 158.7 175 175 175 175
None -- -- 24.6 25.8 26.8 28 30 30 30 35
2TP04520946 9 11.3 38.2 39.4 40.4 41.6 40 40 45 45
2TP04521846 18 22.6 51.7 52.9 53.9 55.1 60 60 60 60
2TP04522446 24 30.1 60.7 61.9 62.9 64.1 70 70 70 70
2TP04523646 34 42.7 75.7 76.9 77.9 79.1 80 80 80 80
None -- -- 20.6 21.1 22.4 22.9 25 25 25 25
2TP04520958 9 9.0 31.4 31.9 33.2 33.7 35 35 35 35
2TP04521858 18 18.1 42.3 42.8 44.1 44.6 45 45 45 45
2TP04522458 24 24.1 49.5 50 51.3 51.8 50 50 60 60
2TP04523658 34 34.1 61.5 62 63.3 63.8 70 70 70 70
*
1.8 0.0
Maximum HACR breaker of the same AMP size is applicable.
52.0 1.3 3.6 4.1
64.0 1.6 4.1
130.0 3.5 8.2
3.5 8.2 10.9130.0 5.5 0.0
5.5 0.0
5.3
10.9
2.2 0.0
460
575
7.7
208
230
14.7
14.7
6.4
Max Fuse* Size
w/Power
Exhaust
(Amps)
FLA FLA
A
ctual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric Heater
Model No.
Max
Fuse*
Size
(Amps)
Voltage
Compressors OD Fan
Motors
Supply
Blower
Motor FLA
TABLE 14: ELECTRICAL DATA BP102 (8-1/2 TON) HP WITH PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
23 2 3 2 3232 3
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 58.3 61.0 63.8 66.5 70 70 70 80
2TP04520925 6.8 18.9 81.9 84.6 87.4 90.1 90 90 90 100
2TP04521825 13.5 37.5 105.1 107.8 110.6 113.3 110 110 125 125
2TP04522425 18.0 50.0 120.7 123.4 126.2 128.9 125 125 150 150
2TP04523625 25.5 70.8 146.8 149.5 152.3 155.0 150 150 175 175
None -- -- 58.3 61.0 63.8 66.5 70 70 70 80
2TP04520925 9.0 21.7 85.3 88.0 90.8 93.5 90 90 100 100
2TP04521825 18.0 43.3 112.4 115.1 117.9 120.6 125 125 125 125
2TP04522425 24.0 57.7 130.4 133.1 135.9 138.6 150 150 150 150
2TP04523625 34.0 81.8 160.5 163.2 166.0 168.7 175 175 175 175
None -- -- 29.6 30.8 31.8 33 35 35 35 40
2TP04520946 9 11.3 43.2 44.4 45.4 46.6 45 45 50 50
2TP04521846 18 22.6 56.7 57.9 58.9 60.1 60 60 60 70
2TP04522446 24 30.1 65.7 66.9 67.9 69.1 70 70 70 70
2TP04523646 34 42.7 80.7 81.9 82.9 84.1 90 90 90 90
None -- -- 24.6 25.1 26.4 26.9 30 30 30 30
2TP04520958 9 9.0 35.4 35.9 37.2 37.7 40 40 40 40
2TP04521858 18 18.1 46.3 46.8 48.1 48.6 50 50 50 50
2TP04522458 24 24.1 53.5 54 55.3 55.8 60 60 60 60
2TP04523658 34 34.1 65.5 66 67.3 67.8 70 70 70 70
*
8.2
1.8 4.0
Maximum HACR breaker of the same AMP size is applicable.
52.0 1.3 3.6 4.1
5.5
10.0
10.0
7.7 64.0 1.6 4.1 5.3 2.2 5.0
10.9
14.7 130.0 3.5 8.2 10.9 5.5
Max
Fuse*
Size
(Amps)
Supply
Blower
Motor FLA
Max Fuse* Size
w/Power
Exhaust
(Amps)
FLA FLA
Actual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric Heater
Model No.
Voltage
Compressors OD Fan
Motors
460
3.5130.0
575 6.4
208
230 14.7

127421-YIM-C-0606
20 Unitary Products Group
TABLE 15: ELECTRICAL DATA BP120 (10 TON) HP W/O PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
23 2 3 2 3232 3
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 51.2 53.9 56.7 59.4 60 60 70 70
2TP04521825 13.5 37.5 98.0 100.7 103.5 106.2 100 110 110 110
2TP04522425 18.0 50.0 113.7 116.4 119.2 121.9 125 125 125 125
2TP04523625 25.5 70.8 139.7 142.4 145.2 147.9 150 150 150 150
2HP04525425** 40.6 112.7 151.1 154.5 158.0 161.4 175 175 175 175
None -- -- 51.2 53.9 56.7 59.4 60 60 70 70
2TP04521825 18.0 43.3 105.3 108.0 110.8 113.5 110 110 125 125
2TP04522425 24.0 57.7 123.4 126.1 128.9 131.6 125 150 150 150
2TP04523625 34.0 81.8 153.4 156.1 158.9 161.6 175 175 175 175
2HP04525425** 54.0 129.9 153.4 156.1 158.9 161.6 175 175 175 175
None -- -- 29.6 30.8 31.8 33 35 40 40 40
2TP04521846 18 22.6 56.6 57.8 58.8 60 60 60 60 60
2TP04522446 24 30.1 65.7 66.9 67.9 69.1 70 70 70 70
2TP04523646 34 42.7 80.7 81.9 82.9 84.1 90 90 90 90
2HP04535446** 54 67.8 80.7 81.9 82.9 84.1 90 90 90 90
None -- -- 20.6 21.1 22.4 22.9 25 25 25 25
2TP04521858 18 18.1 42.3 42.8 44.1 44.6 45 45 45 45
2TP04522458 24 24.1 49.5 50 51.3 51.8 50 50 60 60
2TP04523658 34 34.1 61.5 62 63.3 63.8 70 70 70 70
2HP04535458** 54 54.2 61.5 62 63.3 63.8 70 70 70 70
*
** Only 34 kW of Electric heat can be simultaneously energized with the mechanical heating. The full 54 kW operates only if both compressors are
locked-out.
Maximum HACR breaker of the same AMP size is applicable.
2.2 0.0
6.4 62.0 1.3 3.6 4.1 1.8 0.0
75.0 1.6 4.1
150.0 3.5 8.2
3.5 8.2 10.9150.0 5.5 0.0
5.5 0.0
5.3
10.9
460
575
9.9
208
230
16.0
16.0
Max Fuse Size*
w/Power
Exhaust
(Amps)
FLA FLA
Actual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric Heater
Model No.
Max
Fuse*
Size
(Amps)
Voltage
Compressors OD Fan
Motors
Supply
Blower
Motor FLA
TABLE 16: ELECTRICAL DATA BP120 (10 TON) HP WITH PWRD CONVENIENCE OUTLET
RL
A
LR
A
FL
A
23 2 3 2 3232 3
ea. ea. ea. HP HP HP HP HP HP HP HP HP HP
None -- -- 61.2 63.9 66.7 69.4 70 70 80 80
2TP04521825 13.5 37.5 108.0 110.7 113.5 116.2 110 125 125 125
2TP04522425 18.0 50.0 123.7 126.4 129.2 131.9 125 150 150 150
2TP04523625 25.5 70.8 149.7 152.4 155.2 157.9 150 175 175 175
2HP04525425** 40.6 112.7 163.6 167.0 170.5 173.9 175 175 175 175
None -- -- 61.2 63.9 66.7 69.4 70 70 80 80
2TP04521825 18.0 43.3 115.3 118.0 120.8 123.5 125 125 125 125
2TP04522425 24.0 57.7 133.4 136.1 138.9 141.6 150 150 150 150
2TP04523625 34.0 81.8 163.4 166.1 168.9 171.6 175 175 175 175
2HP04525425** 54.0 129.9 163.4 166.1 168.9 171.6 175 175 175 175
None -- -- 34.6 35.8 36.8 38 40 45 45 45
2TP04521846 18 22.6 61.6 62.8 63.8 65 70 70 70 70
2TP04522446 24 30.1 70.7 71.9 72.9 74.1 80 80 80 80
2TP04523646 34 42.7 85.7 86.9 87.9 89.1 90 90 90 90
2HP04535446** 54 67.8 85.7 86.9 87.9 89.1 90 90 90 90
None -- -- 24.6 25.1 26.4 26.9 30 30 30 30
2TP04521858 18 18.1 46.3 46.8 48.1 48.6 50 50 50 50
2TP04522458 24 24.1 53.5 54 55.3 55.8 60 60 60 60
2TP04523658 34 34.1 65.5 66 67.3 67.8 70 70 70 70
2HP04535458** 54 54.2 65.5 66 67.3 67.8 70 70 70 70
*
** Only 34 kW of Electric heat can be simultaneously energized with the mechanical heating. The full 54 kW operates only if both compressors are
locked-out.
1.8 4.0
Maximum HACR breaker of the same AMP size is applicable.
62.0 1.3 3.6 4.1
10.0
9.9 75.0 1.6 4.1 5.3 2.2 5.0
150.0 8.2 10.9
16.0 150.0 3.5 8.2 10.9 5.5
5.5
10.0
Max
Fuse*
Size
(Amps)
Supply
Blower
Motor FLA
Max Fuse* Size
w/Power
Exhaust
(Amps)
FLA FLA
Actual
KW
Heater
Amps
Min. Circuit
Ampacity
(Amps)
MCA
w/Power
Exhaust
(Amps)
Pwr
Exh
Motor
Pwr
Conv
Outlet Electric Heater
Model No.
Voltage
Compressors OD Fan
Motors
460
3.5
575 6.4
208
230 16.0