Young America Built to Grow 225 Crib Drawer User manual

baby.
A trademark of Stanley Furniture Company, Inc.
Built to Grow Crib Drawer Assembly Instructions
Thank you for purchasing a Built to Grow Crib Drawer. If you find that you are missing a
part or if a part is defective in any way, contact your Young America Baby retailer for
assistance.
ITEM NUMBER
225 Crib Drawer

Identifying the Parts
The drawer illustrations in these instructions are generic in nature. The
drawer you have purchased may not look like the one illustrated; however,
they all assemble in the same manner.
ES
Page 2
baby
A trademark of Stanley Furniture Company, Inc.
(1) FRONI (1)
(2)
LFI 8
(1)

Identifying the Hardware
Identify the hardware included in the hardware bag using the illustrations below
3 Capped connecting bolts
6 Connecting cams
U-
U-
Page 3
3 Threaded connecting bolts
6 Wood screws
#6 X 5/8" long
TOOLS REQUIRED
SCREWDRIVER
(FLAT HEAD)
SCREWDRIVER
—
—
(PHILLIPS)
vouigA ri' icbaby.
A trademark of Stanley Furniture Company, Inc.

Page 4
Step 1: Assemble drawer divider and sides to drawer back
1. Lay the drawer back down so that the groove is facing up as shown in the diagram below.
2. Insert a capped connector bolt from the back of the drawer back through the center hole in the middle of the drawer back.
3. Align the wooden dowels in the end of the drawer divider that is marked "back" with the holes in the center of the drawer
back and the capped connector bolt that you installed.
4. Insert one of the connecting cams into the hole on the side of the drawer divider. Use a Phillips screwdriver and turn the
cam clockwise approximately 1/2 turn to lock the divider to the drawer back.
5. Position the right drawer side so that the grooved edge is aligned with the grooved edge of the drawer back (Refer to
SECTION "A"). Align the dowels in the end of the drawer back with the outer holes that are located on the inside near the end
of the right drawer side.
6. Insert a capped connector bolt through the center hole at the back of the right drawer side.
7. Insert a connecting cam into the hole near the end of the drawer back and turn the cams clockwise approximately 1/2 turn
with a Phillips screwdriver to lock the side to the drawer back.
8. Repeat steps 5, 6, and 7 to attach the left drawer side to the drawer back.
BRAVER DIV1
CONNECTOR
BOLT
DOWEL
CONNECTING
baby
A frademark of Stanley Faraitare Company, Inc.

Step 2: Install crib drawer bottoms
1. Orient one of the crib drawer bottoms so that the "NO STEP' warning label that is located on the white side of the
drawer bottom is facing the top and the front of the drawer assembly. Insert the drawer bottom into the grooves along the
bottom edges of the drawer side and drawer divider. Slide the drawer bottom down into the groove that is in the drawer
back.
2. Repeat #1 to install the other drawer bottom.
DRAWER SIDE
DRAWER ASSEMBLY
Page 5
baby
A frademark of Stanley Faraitare Company, Inc.
DRAWER BOTTOM:
ARNING LABEL
RIB DRAWER BACK
DRAWER SIDE

Step 3: Attach drawer front to crib drawer
1. With the use of a flat head screwdriver, install threaded connecting bolts into the middle holes on the back of the drawer
front at each end and the center (refer to SECTION "A"). Use care not to over tighten these bolts to avoid damage to the
drawer front.
2. Align the dowels, connecting bolts, and the drawer bottom groove with the holes in the ends of the drawer assembly.
3. Install connecting cams into the holes on the side of the drawer sides and drawer divider (refer to SECTION "B"). Using a
phillips screwdriver, turn each connecting cam clockwise approximately 1/2 turn to lock the drawer front to the ends of the
drawer sides and drawer divider.
4. The crib drawer is now fully assembled and ready to install.
Page 6
LAT HEAD
THREADED CONNECTING BOLT
CAM
PHILLIPS
baby
A frademark of Stanley Faraitare Company, Inc.

Step 4: Attach drawer guides to left and right crib ends
NOTE: If your Built to Growtm Crib is already assembled, it is not necessary to disassemble it to attach the
drawer guides. With the help of another person, carefully lay the crib on the back of the headboard to access
the pre-drilled holes on the inside of the crib ends in order to attach the drawer guides.
1. The crib ends are pre-drilled for screws in order to properly locate the drawer guides. Locate the drawer guide that is
stamped with "CL" (this stamp indentifies left hand guide) and align the hole in the guide that is pointed out with the RED
arrow with the pre-drilled hole that is closest to the front of the left crib end.
2. Using a phillips screwdriver, install a #6 X 5/8" long wood screw through the guide and into the pre-drilled hole. Do not
tighten the screw completely at this time.
3. Install 2 additional #6 X 5/8" long wood screws into the holes in the drawer guide that align with the other pre-drilled
holes in the crib end. Tighten all 3 screws so that the heads of the screws are flush with the inside surface of the drawer
guide. This will insure that the drawer will operate smoothly when installed.
4. Locate the drawer guide that is stamped with "CR" (this stamp indentifies right hand guide) and repeat the above steps
to attach the guide to the right crib end.
5. If your crib is not fully assembled refer back to Page 6 of the Built to GrowTM Crib Assembly Instructions at this point. If
the crib is assembled, proceed to the next page of these instructions.
baby
A trademark of Stanley Furaitare Company, Inc.
Page 7
FRONT OF
CRIB
GUIDE WITH 'CL' STAMP
GOES ON LEFT CRIB END
WITH WHEEL TO FRONT
#6 X 5/8' WOOD SCRE'
PHILLIPS SCREWDRIVEI
'RE—BORED HOLES ON INSIDE
OF CRIB END INDICATE WHERE
TO LOCATE SCREWS
OW INDICATES PROPER
FOR FRONT SCREW

Step 5: Install drawer
1. Align the guides that are attached to the drawer sides with the drawer guides that are attached to the crib ends.
2. Lift the back of the drawer so that the rollers that are near the back of the drawer sides go over the rollers of the guides
that are attached to the crib ends.
3. Once the drawer rollers are behind the rollers of the guides on the crib ends, lower the back of the drawer so that the
rollers on the drawer rest on the bottom flange of the guides on the crib ends.
4. Carefully push both ends of the drawer in at the same time until the drawer stops.
5. Installation of the drawer is now complete.
Page 8
baby
A trademark of Stanley Furniture Company, Inc.
ON BRAVER
UP AND OVER ROLLER
ON CRIB ENDS
WARNING!
DRAWER IS NOT A STEP!!

Page 9
CLEANING:
Mix together a mild solution of gentle dishwashing liquid and water, apply to toddler bed surface using a soft
clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all
surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR
COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE:
A plastic sleeve is attached to the crib spring for the storage of the assembly directions for future referral. After
completing the assembly process, you are advised to read and be aware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. We caution you
not to place excess hardware in the plastic sleeve as it could present danger to a child if retrieved and it could
also puncture the crib mattress. When storing toddler bed, use CAUTION as extreme temperature or humidity
changes could be harmful.
PERIODIC MAINTAINANCE:
1. Periodically check to make certain all connectors are fastened securely.
2. If you are missing a part or need a replacement part, do not use substitute parts. Ask your dealer for replacement
parts or contact Customer Service at [phone].
3. Save this instruction sheet in the event you disassemble the drawer and need to reassemble it. This instruction sheet
will also be useful in identifying replacement parts if needed at a future date.
Stanley
FURHTURE
P.O. Box 30
Stanleytown, VA 24168
For parts, contact your Stanley dealer. For additional
consumer information, call our Customer Services Department at
1-(276).627-2100 Mon. - Fri., 8-5 Eastern
baby
A trademark of Stanley Furniture Company, Inc.