Yudor Outdoor Series User manual
USER’S MANUAL
SPEED DOME
V07121-LM
Vandal Proof Series
Indoor Series
Outdoor Series
Outdoor Series
(360° Continuous Rotation)
2
3
SAFETY WARNING
Before using this product, please read installation instructions carefully
and remove the protective lining from the dome before proceeding with
set up.
In case of failure, disconnect power or remove power supply before contact
our service personnel.
To avoid electric shocks, do not disassemble this product on your own. Be
sure to ask a skilled technician for the job.
Use enclosed power supply only. Do not use other type of power supply, or
the product may be damaged or fire can be triggered.
Keep unconnected wires, plugs, duly insulated, or they might cause short
circuit and damage this product.
Do NOT connect power to the unit until all installation steps are completed.
Do not turn the camera lens with your hand, doing so might damage camera.
Do not point this camera to the sun or a shining object, do not put it on a
static object; doing so might damage the camera.
To avoid damage, do not load this camera in a place subject to vibration,
humidity or a dusty environment.
Thanks for your purchase of our product.
In order to make good use of this product, please read this user’s manual carefully.
In order to use this product correctly and safely; be familiar with all operation steps.
Please keep this user’s manual for future reference.
This document contains proprietary information, which is protected by copyright.
The information contained in this document is subject to changes without notice.
4
Safety warning 3
Instructions
1. Accessories
1.1 Indoor Series
6
1.2 Vandal Proof Series
7
1.3 Outdoor Series
8
1.4 Outdoor Series (360° Continuous Rotation) 9
2. Installation
2.1 Indoor Series 10
2.2 Vandal Proof Series 13
2.3 Outdoor Series 14
2.4 Outdoor Series (360° Continuous Rotation)
16
3. Cable Connection
3.1 Indoor Series
19
3.2 Vandal Proof Series
19
3.3 Outdoor Series 20
3.4 Outdoor Series (360° Continuous Rotation) 20
3.5 Wire specification
21
4. Infrared Remote Control
22
5. Initial Programming
5.2 Camera ID setup
23
5.3 Load Default
23
5.4 OSD MENU FUNCTION SETUP
24
5.4.1 GROUP (Auto Pan, Group Auto Cruise, Recorded Cruise)
24
5.4.1.1 AUTOPAN
25
5.4.1.2 GROUP1 ~ GROUP5
25
Table of Contents
61
30.7 AF MODE
Move cursor to AF MODE, press ENTER key to enter AF
MODE menu.
Press UP or DOWN key to select TRC AF/FULL AF.
TRC AF: AF range is 1m~∞.
FULL AF: AF range is Min. Object Distance~∞.
MISC [2/2] MENU
30.8 TRACKING MODE
Move cursor to TRACKING MODE, press ENTER key to
enter TRACKING MODE menu.
Press UP or DOWN key to select AUTO1/AUTO2/FIX.
AUTO1: AF when zoom ratio is x1~x23.
AUTO2: AF when zoom ratio is x6~x23.
MISC [2/2] MENU
When you select FIX., and press ENTER key to enter
TRACKING LEVEL menu.
Press UP or DOWN key to select TRACK LEVEL.
The AF start position as below:
000: ∞.
128: 3m.
255: 1m.
MISC [2/2] MENU
MISC [2/2]
MASK C
MASK D
POSITION OFF
AF MODE →TRC AF
TRACKING AUTO2
MISC [2/2]
MASK C
MASK D
POSITION OFF
AF MODE TRC AF
TRACKING →AUTO1
TRACK LEVEL
TRACK LEVEL 000
60
30.5 MASK A / B / C / D
MASKING AREA SETTING
Move cursor to MASK A/B, press ENTER key to enter
MASK A/B menu.
MISC [1/2] MENU
Move cursor to MASK C/D, press ENTER key to enter
MASK C/D menu.
Press UP or DOWN key to select ON/OFF.
Then press ENTER key to enter MASK A/B/C/D SETTING
menu.
MISC [2/2] MENU
Move cursor to H-POSITION, V-POSITION, H-SIZE or
V-SIZE press ENTER key to enter NUMBER SETTING
menu. Press UP or DOWN key to adjust number.
The ranges of parameters as below:
H-POSITION: -80~+80
V-POSITION: -60~+60
H-SIZE: 0~+80
V-SIZE: 0~+60
MASK A/B/C/D SETING MENU
30.6 DEFAULT POSITION
Default Position when camera power on.
Move cursor to POSITION, press ENTER key to enter
POSITION menu.
Press UP or DOWN key to select position No. (1~64) or OFF.
MISC [2/2] MENU
MISC [1/2]
H-
REVERS OFF
V-REVERS
OFF
POSI/NEGA POSI
PRIORITY AGC
→
MASK A
MASK B
MASK A/B/C/D
H-POSITION →
032
V-POSITION 064
H-SIZE 048
V-SIZE 032
MISC [2/2]
→
MASK C
MASK D
POSITION OFF
AF MODE TRC AF
TRACKING AUTO2
MISC [2/2]
MASK C
MASK D
→POSITION OFF
AF MODE TRC AF
TRACKING AUTO2
5
5.4.1.3 CRUISE
25
5.4.2 ALARM (Alarm Mode Setup)
26
5.4.3 MASK 27
5.4.4 AUTO TRACKING
28
5.4.5 PROTOCOL
29
5.4.6 ID
29
5.4.7 MISC (Manual control speed setup, Auto Flip, Default)
29
Operation
6. Infrared remote control mode
6.1 Select Camera - By Input camera ID
31
6.2 Remote control
31
6.3 Alarm and Output On / Off
31
6.4 Preset Positions CALL, SAVE and CLEAR
32
6.5 Recall Preset Positions
32
6.6 Auto Pan Mode and Group Auto Cruise Mode
32
6.7 Speed activate Auto Tracking Function 32
7. RS-485 Control mode
7.3 Controls
33
7.4 Protecting 33
Remarks
8. Maintenance & cleaning
34
9. Troubleshooting
35
10. Specifications 36
11. Optional accessories
37
12. Lens internal setting
39
6
Please check if the accessories enclosed are completed. If there is any
shortage, please contact your local dealer and replace a new one.
1.1 Indoor Series
1
-
Accessories
1.1.5
Infrared receiver
1.1.6
Infrared
remote control
PAN/TILT
AUTO
2
5
8
0
7
4
1
9
6
3
ARK-503
1.1.7
No. 4 AAA Batteries
1.1.9
User’s manual
1.1.2
Control line
(In camera)
1.1.1
Indoor Speed Dome
1.1.8
Securing screws
1.1.3
Power supply
1.1.4
AC Power Line
59
30.1 H-REVERS
Horizontal Reverse (Mirror) Function
Move cursor to H-REVERS, press ENTER key to enter
FREEZE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
MISC [1/2] MENU
30.2 V-REVERS
Vertical Reverse (Up-side Down) Function
Move cursor to V-REVERS, press ENTER key to enter
FREEZE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
MISC [1/2] MENU
30.3 POSI/NEGA
Positive or Negative Picture Function
Move cursor to POSI/NEGA, press ENTER key to enter
POSI/NEGA menu.
Press UP or DOWN key to select POSI/NEGA.
MISC [1/2] MENU
30.4 PRIORITY
Selecting IR SW INT Detecting Signal
Move cursor to PRIORITY, press ENTER key to enter
PRIORITY menu.
Press UP or DOWN key to select AGC/SENSE UP.
MISC [1/2] MENU
MISC [1/2]
H-REVERS →
OFF
V-REVERS
OFF
POSI/NEGA POSI
PRIORITY AGC
MASK A
MASK B
MISC [1/2]
H-
REVERS OFF
V-REVERS →OFF
POSI/NEGA POSI
PRIORITY AGC
MASK A
MASK B
MISC [1/2]
H-
REVERS OFF
V-REVERS
OFF
POSI/NEGA →POSI
PRIORITY AGC
MASK A
MASK B
MISC [1/2]
H-
REVERS OFF
V-REVERS
OFF
POSI/NEGA POSI
PRIORITY →
AGC
MASK A
MASK B
58
27. SCALE
ZOOM SCALE DISPLAY
Move cursor to SCALE, press ENTER key to enter
SCALE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
The zoom scale will be display on right-down of the screen
in SCALE ON mode.
Note: The zoom scale is non-linear approximate
value. It’s a reference value for user.
Page5 MAIN MENU
28. LANGUAGE
OSD LANGUAGE SELECT
Move cursor to LANGUAGE, press ENTER key to enter
LANGUAGE selecting menu.
Press UP or DOWN key to select ENGLISH, DEUTSCH or
ITALIANO language.
Page5 MAIN MENU
29. WINKER
WINKER SELECT
Move cursor to WINKER, press ENTER key to enter
WINKER selecting menu.
Press UP or DOWN key to select ON/OFF.
Page5 MAIN MENU
30. MISC
Move cursor to MISC, press ENTER key to enter MISC
menu.
Page5 MAIN MENU
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
→MISC
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
→SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
→LANGUAGE ENGLISH
WINKER OFF
MISC
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
→WINKER OFF
MISC
7
1.2 Vandal Proof Series
1.2.1
Vandal Proof
Speed Dome
1.2.2
Control line
(In camera)
1.2.3
Power supply
1.2.5
Infrared receiver
1.2.6 Infrared
remote control
PAN/TILT
AUTO
2
5
8
0
7
4
1
9
6
3
ARK-503
1.2.7
No. 4 AAA Batteries
1.2.10
User’s manual
1.2.8
Screw driver
for Securing screws
1.2.9
Securing screws
1.2.4
AC Power Line
8
1.3.8 Screw driver
for Securing screws
1.3 Outdoor Series
1.3.7
No. 4 AAA Batteries
1.3.1
Outdoor Speed Dome
1.3.6
Infrared
remote control
PAN/TILT
AUTO
2
5
8
0
7
4
1
9
6
3
ARK-503
1.3.5
Infrared receiver
1.3.12
User’s manual
1.3.11
Ceiling mount Bracket
1.3.10
Wall-mount Bracket
1.3.2
Control line
(In camera)
1.3.3
Power supply
1.3.4
AC Power Line
1.3.9
Securing screws
57
23. FOCUS SPEED
FOCUS SPEED ADJUSTMENT
Move cursor to set FOCUS SPEED, press ENTER key to
FOCUS SPEED SELECTING menu, then Press UP or
DOWN key to select MIN, +1, +2, +3, MAX (5 steps
adjustable).
Page4 MAIN MENU
24. GAMMA
GAMMA SELECT
Move cursor to set GAMMA menu, press ENTER key to
select GAMMA mode , then Press UP or DOWN key to
select GAMMA1 or GAMMA2.
GAMMA1 = 0.45
GAMMA2 = 1.0
Page4 MAIN MENU
25. ZOOM + AF
ZOOM TRIGGER AUTO FOCUS
Move cursor to set ZOOM+AF mode, press ENTER key into
select ZOOM+AF menu.
Press UP or DOWN key to select ON/OFF.
Page5 MAIN MENU
26. AF SLEEP
AUTO FOCUS SLEEP
Move cursor to AF SLEEP, press ENTER key to enter
AF SLEEP ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
The image change less than auto focus range in five minutes;
the auto focus will sleep in AF SLEEP ON mode. If the image
change more ±6dB than auto focus range, the auto focus will
wake up.
Page5 MAIN MENU
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED MAX
FOCUS SPEED →MIN
GAMMA GAMMA1
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED MAX
FOCUS SPEED MIN
GAMMA →GAMMA1
SETUP MENU [5/5]
→ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
SETUP MENU [5/5]
ZOOM+AF OFF
→AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
56
19. DEFAULT
RESTART THE CAMERA AND RESET PARAMETERS
TO FACTORY’S DEFAULT.
Move cursor to DEFAULT, press ENTER key to enter
DEFAULT CANCEL/OK menu.
Press UP or DOWN key to select OK, then press ENTER key.
Page4 MAIN MENU
20. FREEZE
FREEZE PICTURE FUNCTION
Move cursor to FREEZE, press ENTER key to enter FREEZE
ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
Page4 MAIN MENU
21. FREEZE MODE
FREEZE FIELD (or FRAME) OF PICTURE FUNCTION
Move cursor to FREEZE MODE, press ENTER key to select
FREEZE MODE menu.
Press UP or DOWN key to select FIELD/FRAME.
Page4 MAIN MENU
22. ZOOM SPEED
ZOOM SPEED ADJUSTMENT
Move cursor to ZOOM SPEED, press ENTER key to enter
ZOOM SPEED SELECTING menu, then Press UP or
DOWN key to select MAX, +3, +2, +1, MIN (5 steps
adjustable).
Page4 MAIN MENU
SETUP MENU [4/5]
DEFAULT →CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED MAX
FOCUS SPEED MIN
GAMMA GAMMA1
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE →OFF
FREEZE MODE FIELD
ZOOM SPEED MAX
FOCUS SPEED MIN
GAMMA
GAMMA1
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE →FIELD
ZOOM SPEED MAX
FOCUS SPEED MIN
GAMMA GAMMA1
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED →MAX
FOCUS SPEED MIN
GAMMA GAMMA1
9
1.4.14
User’s manual
1.4 Outdoor Series (360° Continuous Rotation)
1.4.6 Infrared
remote control
PAN/TILT
AUTO
2
5
8
0
7
4
1
9
6
3
ARK-503
1.4.5
Infrared receiver
1.4.4
AC Power Line
1.4.2
Control line
1.4.3
Power supply
1.4.1
Outdoor Speed Dome
1.4.7
No. 4 AAA Batteries
1.
4.8
Stable Lid
1.4.9
Spacer (Transparent)
1.4.11
Wall-mount Bracket
1.4.10
Spacer (White)
1.4.12
Spacer (White)
1.4.13
U Shape Spanner
10
2.1 Indoor Series
2.1.1 Names of parts
A. Mounting plate
B. Top line outlet
C. Side line outlet (2 Outlet)
D. Base
E. Dome cover
F. Mounting hole (4 Hole)
G. Mounting slot for Flush mount
bracket (3 Hole)
2.1.2 Remove protective lining
2.1.2.1 Turn the dome cover clockwise to open it and
carefully remove protective lining
2.1.2.2 Place the dome cover back and turn tightly
(counterclockwise).
※
Do not touch the lens with your hands or other object
※
Do not turn the lens or remove other parts; doing so may cause damage.
2.1.3 Basic setup
2.1.3.1 Please refer to 3.1 Cable Connection and 3.5 Cable specification: connect
Power line, Video cable, Infrared receiver insulation cable first，then
connect Alarm cable and RS-485 PVC instrument cable (pair type) if
needed。
2.1.3.2 Load batteries into infrared remote control and use infrared remote control to
setup camera ID and RS-485 control protocol. Please refer to
4 Infrared Remote control and 5 Initial Programming.
2
-
Installation
55
Press ENTER key to enter IR INT LEVEL ADJUSTMENT
menu.
Press UP or DOWN key to select IR INT LEVEL MIN, +1, +2,
+3, +4, +5, +6, +7, +8, +9, +11, +12, +13, +14, +15, +16, MAX,
18 steps adjustable.
IR INT LEVEL MENU
*1
*2
*3
OFF x 2 x 4 x 6 x 8 x 12 x 16 x 32 x 64
BASE x x MAX 16 15 14 13 11 9
+1 x MAX 15 14 13 12 11 9 7
+2 x 16 14 13 12 11 10 8 6
+3 x 15 13 12 11 10 9 7 5
+4 MAX 14 12 11 10 9 8 6 4
+5 16 13 11 10 9 8 7 5 3
+6 15 12 10 9 8 7 6 4 2
+7 14 11 9 8 7 6 5 3 1
MAX 13 10 8 7 6 5 4 2 MIN
IR INT LEVEL TABLE
NOTE1:
*1: AGC LEVEL
*2:IR INT LEVEL (ACT UP THE LEVEL)
*3:SENSE UP
NOTE2: IR INT LEVEL (MAX) Approach 15Lux (illumination)
IR INT LEVEL (MIN) Approach 0.02Lux (illumination)
18. INITIAL
LENS RESET FUNCTION
Move cursor to INITIAL, press ENTER key to enter
INITIAL ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
When you select ON, the lens will initial again.
Page3 MAIN MENU
IR INT LEVEL
IR INT LEVEL →MAX
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION ON.
IR AUTO.
INITIAL →ON
54
Press ENTER key to enter MOTION FUNCTION menu.
Press UP or DOWN key to select motion detection AREA,
LEVEL (Sensitivity), TIME, OSD.
When detecting motion, it will display MOT on the screen.
MOTION MENU
Press ENTER key to enter MOTION AREA menu.
Press UP or DOWN key to select motion detection
H-POSITION, V-POSITION, H-SIZE and V-SIZE.
The ranges of parameters as below:
H-POSITION: -80~+80
V-POSITION: -60~+60
H-SIZE: 0~+80
V-SIZE: 0~+60
MOTION AREA MENU
17. IR
IR FILTER REMOVABLE FUNTION (DAY & NIGHT FUNCTION)
Move cursor to IR, press ENTER key to enter IR
AUTO/DAY/NIGHT menu.
You can press UP or DOWN key to select AUTO / DAY
/NIGHT.
When you select DAY/NIGHT mode, camera will fix on Color
or BW mode.
Page3 MAIN MENU
Press ENTER key to enter IR SW FUNCTION menu.
Press UP or DOWN key to select IR SW detection INT.
IR SW can detect INT. (AGC and SENSE UP) signal.
IR SW INT. MENU
MOTION
→
AREA
LEVEL +4
TIME 30sec
OSD OFF
IR SW
IR SW →INT.
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION ON.
IR →AUTO.
INITIAL ON
AREA
H-POSITION 00
V-POSITION 00
H-SIZE 65
V-SIZE 44
11
2.1.4 Install mounting plate
2.1.4.1 Remove mounting plate
Please turn mounting plate clockwise approximately 15° to separate the
mounting plate and the base
2.1.4.2 Please select suitable location to install IP Speed dome. The long aperture
should face backward of monitoring scope and take 1.1.8-Securing Screws to
secure the mounting plate. (The dimensions of mounting hole please refer to
figure below).
※
Before installation, make sure the structure of location you choose can hold the
weight of camera.
12
2.1.5 Combine mounting plate with Speed Dome
Long aperture of mounting plate aim to point K (middle of two wire outlet) Turn
Speed Dome clockwise approximately 15°, long aperture will meet wire outlet L.
Make sure speed combine with mounting plate tightly. (Refer to figure below).
2.1.6 Other way to install Speed Dome
Flush Mount (Bracket is optional) Wall mount (Bracket is optional)
2.1.7 When finished all above steps, please connect the control connecting line to related
facilities. (Refer to 3 Cable Connections, Indoor Series) Please make sure all
installation steps are correct then connect power.
※
Keep unconnected wires, plugs, duly insulated, or they may cause short circuit and
damage this product.
Diagram of finished installation
53
14 H-GAIN
This is used to enhance the compensation of the picture quality.
H-GAIN: Horizontal Compensation
Move cursor to H-GAIN, press ENTER key to enter H-GAIN
ADJUSTMENT menu.
Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6,
+7, +8, +9, +11, MAX, 13 steps adjustable.
Page3 MAIN MENU
15. V-GAIN
This is used to enhance the compensation of the picture quality.
V-GAIN: Vertical Compensation
Move cursor to V-GAIN, press ENTER key to enter V-GAIN
ADJUSTMENT menu.
Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6,
+7, +8, +9, +11, MAX, 13 steps adjustable.
Page3 MAIN MENU
16. MOTION
MOTION DETECTION FUNCTION
Move cursor to MOTION, press ENTER key to enter
MOTION ON/OFF menu.
Press UP or DOWN key to select ON.
Page3 MAIN MENU
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN →+6
V-GAIN +6
MOTION OFF
IR AUTO
INITIAL ON
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN →+6
MOTION OFF
IR AUTO.
INITIAL ON
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION →ON.
IR AUTO.
INITIAL ON
52
Press ENTER key to enter POSITION LOAD SELECTNG
menu.
Press UP or DOWN key to select position (1 to 64 position that
you want to LOAD), then press ENTER key that will be
loaded.
POSITION LOAD MENU
Press ENTER key to enter ALARM POSITION SELECTNG
menu.
Press UP or DOWN key to select alarm position (OFF, 1 to 64
position that you want to set), then press ENTER key that will
be set.
When input alarm signal, alarm position will be loaded.
ALARM POSITION MENU
Press ENTER key to enter ALARM POSITION SELECTNG
menu.
Press UP or DOWN key to select alarm delay time (OFF, 1 ~
60 sec. that you want to set), then press ENTER key that will
be set.
ALARM POSITION MENU
Display position number.
OSD set ON, position number will be display on
right-up(R-U) or right-down(R-D) of the screen.
POSITION OSD MENU
POSITION LOAD
POSITION LOAD →
1
ALARM POSITION
ALARM POSITION →OFF
DELAY TIME OFF
POSITION OSD
OSD →
OFF
POSITION R-U
ALARM POSITION
ALARM POSITION OFF
DELAY TIME →OFF
13
2.2 Vandal Proof Series
2.2.1 Names of parts
A. Dome cover
B. Base
C. Mounting hole
D. Securing screw
E. Waterproof joint (Do not open)
F. Waterproof ring
2.2.2. Remove protective lining
2.2.2.1 Use screwdriver (accessory 1.2.8) turns
counterclockwise to remove all securing
screws.
2.2.2.2 Remove dome cover and waterproof ring.
2.2.2.3 Remove protective lining.
2.2.2.4 Load waterproof ring and dome cover back
and tighten securing screws (turn clockwise).
※
Do not touch lens with your hands or other objects.
※
Do not turn the lens or remove other parts. Doing so may cause damage.
※
Do not scratch the dome cover or touch any parts.
※
Make sure all the screws are properly tightened to keep Vandal speed dome waterproof.
2.2.3 Basic setup
2.2.3.1 Please refer to 3.1 Cable Connection and 3.5 Cable specification: connect
Power line, Video cable, Infrared receiver insulation cable first，then
connect Alarm cable and RS-485 PVC instrument cable (pair type) if
needed.
2.2.3.2 Load batteries into infrared remote control and use infrared remote control to
setup camera ID and RS-485 control protocol. Please refer to
4 Infrared Remote control and 5 Initial Programming.
2.2.4 Install Speed Dome
Use securing screws (accessory 1.2.9) install speed dome in an appropriate
position. Before installation, make sure the structure of location you choose can
hold the weight of camera. (2.4Kg)
※
Keep unconnected wires, plugs, duly insulated, or they may cause short circuit and
damage this product.
14
2.3 Outdoor Series
2.3.1 Names of parts
A. Outer layer of base
B. Base
C. Cover
D. Wall mounted Bracket
E. Wire sheathing
F. Securing screws for wire sheathing
2.3.2 Remove protective lining.
2.3.2.1 Turn counterclockwise and carefully remove
the protective lining.
2.3.2.2 Remove securing screw for shipment (M4 *10mm) by turning
counterclockwise (As mark below).
※
Warning: Securing screw for shipment must be properly tightened
before shipping this product
。
51
Press UP or DOWN key to select FOCUS FAR to NEAR.
FOCUS ADJUSTMENT MENU
12. AUTO FOCUS
Move cursor to AUTO FOCUS, press ENTER key to enter
AUTO FOCUS FUNCTION SELECTING menu.
Press UP or DOWN key to select AUTO FOCUS ON or OFF.
Page2 MAIN MENU
13. POSITION
Move cursor to POSITION, press ENTER key to enter
POSITION FUNCTION SELECTING menu.
Press UP or DOWN key to select LOAD, SAVE, ALARM, and
OSD.
Page3 MAIN MENU
There have 64 steps (position with zoom & focus) can be
programmed.
After adjusting position with zoom & focus, Press ENTER key
to enter POSITION SAVE SELECTNG menu.
Press UP or DOWN key to select position (1 to 64 position that
you want to save), then press ENTER key that will be saved.
POSITION SAVE MENU
FOCUS
FAR - - - - - - - - - - -
NEAR
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC OFF
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS →ON
SETUP MENU [3/5]
POSITION →LOAD.
H-GAIN +6
V-GAIN +6
MOTION OFF
IR AUTO.
INITIAL ON
POSITION SAVE
POSITION SAVE →1
50
Press UP or DOWN key to select ZOOM WIDE to TELE, 1 to
23 times adjustable.
ZOOM ADJUSTMENT MENU
10. DIGITAL ZOOM
Move cursor to DIGITAL P/T/Z, press ENTER key to enter
DIGITAL P/T/Z SELECTING MENU.
Page2 MAIN MENU
Press UP or DOWN key to select DIGITAL ZOOM ON or
OFF (1 to 10 times adjustable).
The ranges of P/T/Z adjustment as below:
PAN: -72~+72
TILT: -54~+54
WIDE: 0~80
CANCEL: Recall the default values.
DIGITAL P/T/Z SELECTING MENU
11. FOCUS
Move cursor to FOCUS, press ENTER key to enter FOCUS
ADJUSTMENT menu.
Page2 MAIN MENU
ZOOM
WIDE - - - - - - - - - - -
TELE
SETUP MENU [2/5]
WHITE BAL AWB
.
SYNC OFF
ZOOM
→DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
SETUP MENU [2/5]
WHITE BAL AWB
.
SYNC OFF
ZOOM
DIGITAL P/T/Z
→
FOCUS
AUTO FOCUS OFF
DIGITAL P/T/Z
MAX x10
PAN 00
TILT 00
WIDE 76
CANCEL
15
2.3.2.3 Loads cover back and tightened all securing screws (Turn clockwise). Make
sure all the screws are properly tightened to keep camera waterproof
2.3.2.4 Use securing screws (accessory 1.3.9) and choice of Wall mount bracket
(accessory 1.3.10) or Ceiling mount bracket (accessory 1.3.11) install camera
in an appropriate position.
※
Do not touch lens with your hands or other objects.
※
Do not turn the lens or remove other parts. Doing so may cause damage.
※
Ceiling mount bracket(accessory 1.3.11) is for indoor use.
※
Make sure junction between dome cover
、
speed dome and bracket are air tight
sealed with Silicon glue to keep speed dome waterproof.
2.3.3 Basic setup
2.3.3.1 Please refer to 3.1 Cable Connection and 3.5 Cable specification: connect
Power line, Video cable, Infrared receiver insulation cable first, then
connect Alarm cable and RS-485 PVC instrument cable (pair type) if
needed.
2.3.3.2 Load batteries into infrared remote control and use infrared remote control to
setup camera ID and RS-485 control protocol. Please refer to
4 Infrared Remote control and 5 Initial Programming.
2.3.4 Install Speed Dome
Install speed dome in an appropriate position. Before installation, make sure the
structure of location you choose can hold the weight of camera. (3.44Kg)
。
※
Keep unconnected wires, plugs, duly insulated, or they may cause short circuit and
damage this product.
16
2.4 Outdoor Series (360° Continuous Rotation)
2.4.1 Names of parts
A. Outer layer of base
B. Base
C. Cover
D. Stable Lid
E. Wall mounted Bracket
2.4.2 Insert control line
2.4.2.1 Insert accessories 1.4.2 Control Line
into accessories 1.4.11 Wall Mount
Bracket (As Diagram on right).
2.4.2.2 Install speed dome in an appropriate
position. Before installation, make sure the structure of location you choose
can hold the weight of camera. (3.5Kg)
2.4.3 Lay on Waterproof Spacer
Lay on accessories 1.4.12 Waterproof spacer,
(As Diagram on right).
2.4.4 Plug in connector
Insert control line into gap on the side of top of speed dome, and plug in 2 sets of
connector.
(6 pin and 7 pin, directional)
49
Move cursor to B-Y GAIN, press ENTER key to enter B-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
8. SYNC
This function is used to adjust phase of external sync.
When input external sync, we can press ENTER key to set
SYNC ON, then into the PHASE ADJUSTMENT MENU.
Page2 MAIN MENU
Press UP or DOWN key to adjust phase. The Adjust range
is –130~+130.
PHASE ADJUSTMENT MENU
4.9 ZOOM
Move cursor to ZOOM, press ENTER key to enter ZOOM
ADJUSTMENT menu.
Page2 MAIN MENU
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC →ON
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
SETUP MENU [2/5]
WHITE BAL AWB
.
SYNC OFF
→ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
OUT DOOR
LEVEL MIDDLE
R-
Y GAIN +4
B-Y GAIN →+4
PHASE CONTROL
PHASE CONTROL →000
48
Move cursor to B-Y GAIN, press ENTER key to enter B-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
7.4 Out Door
Move cursor to WHITE BAL, press ENTER key to enter
WHITE BAL FUNCTION SELECTING menu, then Press UP
or DOWN key to select OUTDOOR.
Press ENTER key to enter OUTDOOR LEVEL
ADJUSTMENT menu.
Page2 MAIN MENU
Press ENTER key to enter OUTDOOR LEVEL
ADJUSTMENT menu, then Press UP or DOWN key to select
RED, RED+, RED++, RED+++, MIDDLE, BLUE, BLUE+,
BLUE++, BLUE+++, 9 steps adjustable.
OUTDOOR LEVEL ADJUSTMENT MENU
Move cursor to R-Y GAIN, press ENTER key to enter R-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
IN DOOR
LEVEL MIDDLE
R-
Y GAIN +4
B-Y GAIN →+4
SETUP MENU [2/5]
WHITE BAL →OUTDOOR
.
SYNC OFF
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
OUT DOOR
LEVEL →
MIDDLE
R-
Y GAIN +4
B-Y GAIN +4
OUT DOOR
LEVEL MIDDLE
R-Y GAIN →
+4
B-Y GAIN +4
17
2.4.5 Assembling speed Dome with Bracket
2.4.5.1 Insert speed dome into round hole of bracket.
2.4.5.2 Lay on accessories 1.4.10 Waterproof spacer
(White)、1.4.9 Waterproof spacer
(Transparent) as Diagram.
2.4.5.3 Lay on accessories 1.4.8 Stable Lid, screw
with hand.
2.4.6 Stable speed dome
Stable speed dome with 10mm hexagonal Spanner,
Turn clockwise.
2.4.7 Put on Dome Cover
Use Accessories 1.4.13 U shape spanner, Turn clockwise.
※
Do not touch lens with your hands or other objects.
※
Do not turn the lens or remove other parts. Doing so may
cause damage.
※
Make sure junction between dome cover
、
speed dome and bracket are air tight
sealed with Silicon glue to keep speed dome waterproof.
18
2.4.8 Basic Setup
2.4.8.1 Please connect power line, video, Infrared receiver first, Connect RS-485
control, alarm in and out if necessary. (Please refer to 3.4 Connection Chart
and 3.5 Cable specification).
2.4.8.2 Load batteries into remote controller, point to infrared receiver, setup
camera ID and Protocol of RS-485. Please refer to
4 Infrared Remote control and 5 Initial Programming.
※
Keep unconnected wires, plugs, duly insulated, or they may cause short circuit and
damage this product.
47
Move cursor to B-Y GAIN, press ENTER key to enter B-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
7.3 In Door
Move cursor to WHITE BAL, press ENTER key to enter
WHITE BAL FUNCTION SELECTING menu, then Press UP
or DOWN key to select INDOOR.
Press ENTER key to enter INDOOR LEVEL ADJUSTMENT
menu.
Page2 MAIN MENU
Press ENTER key to enter INDOOR LEVEL
ADJUSTMENT menu, then Press UP or DOWN key to select
RED, RED+, RED++, RED+++, MIDDLE, BLUE, BLUE+,
BLUE++, BLUE+++, 9 steps adjustable.
INDOOR LEVEL ADJUSTMENT MENU
Move cursor to R-Y GAIN, press ENTER key to enter R-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
AWB LEVEL
AWB LEVEL MIDDLE
R-
Y GAIN +4
B-Y GAIN →+4
SETUP MENU [2/5]
WHITE BAL →INDOOR
.
SYNC OFF
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
IN DOOR
LEVEL →
MIDDLE
R-
Y GAIN +4
B-Y GAIN +4
IN DOOR
LEVEL MIDDLE
R-Y GAIN →
+4
B-Y GAIN +4
46
Move cursor to B-Y GAIN, press ENTER key to enter B-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
7.2 AWB (Auto White Balance)
Move cursor to WHITE BAL, press ENTER key to enter
WHITE BAL FUNCTION SELECTING menu, then Press UP
or DOWN key to select AWB.
Press ENTER key to enter AWB LEVEL ADJUSTMENT
menu.
Page2 MAIN MENU
Press ENTER key to enter AWB LEVEL ADJUSTMENT
menu, then Press UP or DOWN key to select RED, RED+,
RED++, RED+++, MIDDLE, BLUE, BLUE+, BLUE++,
BLUE+++, 9 steps adjustable.
AWB LEVEL ADJUSTMENT MENU
Move cursor to R-Y GAIN, press ENTER key to enter R-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
ATW LEVEL
ATW LEVEL MIDDLE
R-
Y GAIN +4
B-Y GAIN →+4
SETUP MENU [2/5]
WHITE BAL →AWB.
SYNC OFF
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
AWB LEVEL
AWB LEVEL →
MIDDLE
R-Y GAI
N +4
B-Y GAIN +4
AWB LEVEL
AWB LEVEL MIDDLE
R-Y GAIN →
+4
B-Y GAIN +4
19
3.1 Indoor Series
3.2 Vandal Proof Series
3
-
Cabl e Connection
20
3.3 Outdoor Series
3.4 Outdoor Series (360° Continuous Rotation)
45
6. AGC (Auto Gain Control)
Move cursor to AGC, press ENTER key to enter AGC LEVEL
SELECTING menu, then Press UP or DOWN key to select
BASE, +1, +2, +3, +4, +5, +6, +7, MAX (0dB ~ 36dB, 9 steps
adjustable).
AGC ADJUSTMENT MENU
7. WHITE BALANCE
7.1 ATW (Auto Trace White Balance)
Move cursor to WHITE BAL, press ENTER key to enter
WHITE BAL FUNCTION SELECTING menu, then Press UP
or DOWN key to select ATW.
Press ENTER key to enter ATW LEVEL ADJUSTMENT
menu.
Page2 MAIN MENU
Press ENTER key to enter ATW LEVEL ADJUSTMENT
menu, then Press UP or DOWN key to select RED, RED+,
RED++, RED+++, MIDDLE, BLUE, BLUE+,
BLUE++,BLUE+++, 9 steps adjustable.
ATW LEVEL ADJUSTMENT MENU
Move cursor to R-Y GAIN, press ENTER key to enter R-Y
GAIN ADJUSTMENT menu, then Press UP or DOWN key to
select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
SETUP MENU [1/5]
CAMERA ID OFF
SENSE UP OFF
AISHUT AUTO.
AES FIX.
BLC OFF
AGC →+4
SETUP MENU [2/5]
WHITE BAL →ATW.
SYNC OFF
ZOOM
DIGITAL P/T/Z
FOCUS
AUTO FOCUS OFF
ATW LEVEL
ATW LEVEL →
MIDDLE
R-Y GAIN +4
B-Y GAIN +4
ATW LEVEL
ATW LEVEL MIDDLE
R-Y GAIN →
+4
B-Y GAIN +4
This manual suits for next models
1
Table of contents
Other Yudor Security Camera manuals
