Z Flash OBD-II SWITCH User manual

USER MANUAL
OBD-II Switch
Switch Hardwire
*Patent Pending TheZFlash.com
OBD-II SWITCH • FORD
Version 1.0

LED Indicator Light Button Operation
Red LED = module off One second press = on/off
Green LED = module on Five second press = pattern
change
Green LED blinking then pause =
indicates pattern number
Wire Color Mode
Blue Mode 1
Yellow Mode 2
Blue and Yellow Mode 3
1
Congrats on purchasing your Z-Flash! Your Z-Flash is ready to start ashing
your factory lights right out of the box. Follow the steps below to get started:
1. Plug the switch or hardwire into the 2x2 port on the side of your Z-Flash module and follow the
respective instructions below. Then plug your Z-Flash module into the OBD-II port (see page 2 for
more details).
2. Test out your module! If you want to change or edit any of the patterns, use the provided USB cable
and plug your Z-Flash into your Windows computer. Visit TheZFlash.com for full instructions and video
tutorials on how to edit or create your own patterns.
Using your module with the Switch:
1. Connect the 2x2 plug on the switch into the port
on the side of your Z-Flash module.
2. Clean the surface where you want to stick
the switch with alcohol and wait for it to dry
completely.
3. Remove the paper backing and stick the switch. Careful! You only have one attempt to get the switch
to stick. Remember to apply light pressure ensuring the entire switch mounting pad is making contact
with the mounting area.
4. Press and hold the button on the switch for one second to activate the module. The light will change
from red to green to indicate the Z-Flash is activated.
5. To change the pattern, press and hold the button for 5 seconds. Above is a full chart on how to use
the switch.
Using your module with the Hardwire:
1. Connect the 2x2 plug on the switch into the port
on the side of your Z-Flash module.
2. Set your ash pattern for each mode using the
Z-Flash software available at TheZFlash.com.
3. Follow the chart to connect mode 1, 2, and/or 3
to +12V.

2
1. Connect the module into the vehicle’s OBD-II
port. The OBD-II port is located under the
dashboard on the driver’s side.
2. Start your vehicle.
3. The module will begin to boot and the LED
will ash for 5 seconds.
4. When the module is ready to use the green
LED will ash for 5 seconds and then turn off.
5. If you need to disconnect the module and
plug it back in, you will need to follow the boot
sequence again. Make sure the module is
turned off before removing it.
OBD-II MODULE INSTALLATION
This warranty protects the product(s) specied to be free
from defects in material and workmanship for 1 (one) year.
During the warranty period we will, at our sole discretion,
repair or replace the product(s). This limited warranty does
not cover travel expense or labor charges for the removal and
reinstallation of the product, or any other charges alike. We
are not responsible for incidental damages, including but not
limited to: loss of time, loss of work, inconvenience, loss and/
or damage to personal property, shipping expenses. We are in
no way responsible for any loss or any indirect or consequential
damages resulting from any such defect in material and/
or workmanship whether it’s due to negligence, incorrect
installation, or manufacturer mistake. It is the sole responsibility
of the party initiating a warranty claim to pay shipping charges
associated with returning a product.
• If you do not know what you are doing, do not try.
• We advise professional installation for all products.
• Electrical shock can cause injury or death. Please use proper
tools and protection when installing. Professional installation
is strongly advised.
• Please check for correct installation method
before powering on. Electrical re can occur.
• Do not run any wires in the way of air
bags or other safety devices.
Warranty: Warning: