Zamp Solar 60A Deluxe User manual

60A Deluxe Roof Mounted Quick Start Guide
Optional Expansion
Kit Available
Optional Expansion
Kit Available
640-Watt DX Kit
Terminal Block
Fuse Block
RT-1
Fuse Blocks
Terminal Block
Optional Expansion
Kit Available
PRT1004

1. Arrange the layout of your panels and wire, ensuring that:
- 3-port roof cap is no more than 15’ from charge controller
- panel leads can reach 3-port roof cap
- charge controller is no more than 9’ from battery
- panels are not shaded by vents, AC units, or other obstructions
2. Connect 15’ Solar wire(s) to the 3-port roof cap(s).
- Strip the ends of both positive and negative wires ½ inch
- Screw the red (+) wire into corresponding positive terminal, black (-) wire into corresponding
negative terminal.
3. Mount 3-port roof cap(s) and route the 15’ cable(s) from roof to charge controller location
*Do not make connections at this time
4. Proceed to install the wires from both roof caps to the corresponding terminal on the charge
controller , ensuring connection is tight. (2 red on red, 2 black on black) Repeat with battery harness.
*Connect RT-1 wires to charge controller and proceed with RT-1 install as per the manual instructions.
5. Mount your charge controller
6. Install the fuse block onto the positive battery terminal.
7. Connect the positive wire to the fuse block
8. Connect the black wire to the negative battery terminal
9. You may now plug the SAE solar panel leads into the 3-port cap(s) and uncover the panels
10. You are now charging your battery.
11. Configure your charge controller to the proper battery type
Install Instructions:
Install Safety:
- Inspect the installation area for
safety hazards
- Be sure to remove all metal such
as rings and other jewlery
- Dissconnect all power sources
and ensure solar panels are
completely covered by a box or
blanket until installation is done
60A Deluxe Roof Mounted Quick Start Guide
Install Tools:
- Flat head screwdriver
- Philips head screwdriver
- Wire stripper
- Self-Leveling Sealant

Common solar wiring for multiple 12-Volt Batteries
How TO wire a solar controller for 2 batteries
When wiring a solar kit to multiple batteries, it is important to remember that your batteries are wired together. To gain the most from your solar
kit, be sure to place the positive wire on the first battery in the sequence and the negative wire on the last battery in the sequence. This is true
regardless of the number of batteries in the bank.
How NOT to wire a solar controller for 2 batteries
+
-
+
-
+
-
+
-
+
-
+
-
+
-
How TO wire a solar controller for 3 batteries
Fuse Block
Z-6-2018

US Removable Mounting Feet Quick Start Guide
1. Find placement for your panel(s) on roof.
2. Install mounting feet to panel by following the diagram.
3. Tighten ¼-20 nuts to approximately 20 foot lbs of torque.
4. Mark the location of the mounting foot (C) holes on
the roof of your RV.
5. Drill holes as indicated by the marks from previous step.
6. Apply a generous amount of sealent to the RV roof
where mounting feet and screws will be placed.
7. Place panels and mounting feet over the drilled and
sealed areas.
8. Install the mounting screws (C) and let sealent set.
9. Retighten as needed.
Install Instructions:
Included Mounting Foot Components
- B (4) Mounting Foot Top
- C (4) Mounting Foot Bottom
- D (4) Lock Washer
- E (4) ¼-20 Nuts
Not Included Components
- Tube of UV Rated Adhesive Sealent
- Drill
- F (8) Mounting Screws (size #8)
Mounting
Foot Bottom
(C)
Mounting
Foot Top
(B)
Mounting
Screws
(F)
Solar Panel
Omni-Mount
Frame
(A)
Mounting
Foot Bottom
(C)
Omni-Mount
Frame
(A)
Mounting
Foot Top
(B)
Lock Washer
(D)
¼-20-Nut
(E)
Solar Panel
Top View Side View