Zebronics BTM9801RUCF User manual

www.zebronics.com
User Manual
ZEB
Tower Speaker
BTM9801RUCF
auh
INPUT
ST.BY MUTE VOL- VOL+
USB
SD/MMC CARD
OFF OFF
INPUT SAVE EQ MUTE
VOL+
VOL-
AUTO
CH TUNE
DISP+
DISP-
1 2 3
456
789
0
REPEAT RESET

Features:
1. With built-in amplifier design, the
speaker reflect the purity of Sound and
creates powerful sound effect.
2. Ideal for PC and audio sources such as CD,
DVD, Bluray, TV, etc.
3. Magnetically shielded for use with
P C m o n i t o r a n d T V w i t h o u t a n y
interference.
4. Dedicated volume, treble, bass controls,
plug and play microphone ports
Note:
1. D o n ' t p u t t h e s p e a k e r s i n h i g h
temperature or humid environment,
avoiding water and to prevent from
electric shock.
2. Don' t open the speakers to avoid electric
shock or other accidents.
3. In case of any liquid fallen into the
speakers, cut off the power immediately
and contact the nearby authorised service
center.
4. When receiving high output signal from
any audio sources(SD, USB, AUX, FM) don' t
(BT, ARC, OPTICAL, COAXIAL) turn the
volume to maximum to avoid sound
distortion.
5. For indoor use only.
6. Plug off the power plug in case of no utility
for long period of time.

Utility Description:
1. Connect the one end of the right tower
cable to the right output port on the back
panel of the left tower. Also place the cable
extended tower to the right side and the
other to the left side while listening.
2. Connect one end of 3.5mm stereo audio
plug to the audio output of PC or other
audio sources.
3. Make sure all the cables above are
connected correctly, then connect the
power cord to AC power.
4. Switch on the power with the red led display
showing (-----). then press power button
either on the remote or left speaker front
panel.
5. The SB Mode in the Mic represents the
standby mode which works when the Mic is
to be stopped for few seconds or minutes
without being switched off.
Package contents:
Tower speaker : 2 U
Remote control : 1 U
Wireless Mic : 2 U
Input cable : 2 U
Antenna cable : 1 U
QR Code guide : 1 U

How to use the BT:
1. Select the audio input to BT status
2. Search BT device with name
"ZEB-BTM9801RUCF”
3. Connect the BT
4. If your BT device below 2.0 version, input
password "0000" when connecting.

Front Panel Description:
VOL- / CH-
|
9 Moves to the previous track for play if
in USB or SD or BT Mode moves to the previous
channel if in the FM Mode / Decreases the volume
level if touch and hold continuously.
During FM Playback touch and hold AUTO /4;
for 2-3 Sec to start auto scan for FM Channels / Play or
pause a current playing track.
Moves to the next track in USB or SD VOL+ / CH+
|:
or BT mode moves to the next channel in the FM
Mode/Touch and hold will increase the volume level.
Mute or UnmuteMUTE
Long touch to Power ON/OFF the INPUT/ST.BY
speaker. After switching the speaker ON, Short touch
consecutively to switch between different input
modes FM / SD / USB / BT / AUX / OPTICAL IN / HDMI
(ARC) / COAXIAL IN.
SD/MMC card slot SD/MMC CARD
USB Socket USB
INPUT
ST.BY MUTE AUTO VOL-/CH-
VOL+/CH+
USB
SD/MMC CARD

Remote Control Description:
Power switch
button(standby) switch On
or off for waiting or On
condition.
Select the INPUT
Source Input
SAVE Save FM
Channel
EQ Equalizer preset
MUTE Mute or
Unmute
VOL-/+ Master Volume
4
;/ AUTO Play & Pause
Track. Press & Hold for FM
Scanning
9 Previous track
when USB/SD/BT Input
Next track :
when USB/SD/BT Input
To Adjust DISP-/+
display brightness
CH-/+ Previous /Next
Channel When FM Input
TUNE-/+ Previous/Next
Channel Keep Pressing to
search the channel
REPEAT Repeat All
Tracks or Single Track
When The RESET
Volume Is at The
Maximum,Press "RESET"
Button at The Status While
Power On
Press any key to
choose the track

Speakers Connectivity Diagram:
Note: Insert the plugs fully into the jacks. Loose
connections may produce a humming sound or other noise
interference.
Important: Connect the speaker and all other external
device and finally connect the AC power cord.
COAXIAL
INPUT HDMI
INPUT
OPTICAL
INPUT
auh
INPUT
ST.BY MUTE VOL- VOL+
USB
SD/MMC CARD

Side Panel & Microphone Description:
VOLUME +/- Volume control
TREBLE +/- Treble control
BASS +/- Bass control
ECHO +/- Microphone echo control
MIC.VOL +/- MIC volume.

Instructions for Use:
General Instructions
BT Mode:
Power ON the speaker, short touch
“INPUT/ST.BY” button on control panel or
remote control to switch to BT Mode with the
LED Display. Switch ON BT on your phone or
tablet and search for nearby BT Devices, search
for the BT name “ZEB-BTM9801RUCF” and tap
to connect it.
FM Mode:
Switch the speaker to FM Mode, Long
touch the Play / Pause button in remote
control to scan the channels automatically.
Use Next / Prev buttons in remote control
or front control panel to change the channels.
USB Mode:
The speaker automatically switches to
USB input mode with the LED display when a
USB flash drive is inserted. Ensure that your
USB flash drive contains MP3 audio files.
AUX-IN:
Switch the speaker to AUX Mode. The
speaker can be connected to an audio device
using an RCA to 3.5mm cable. Connect the one

end of the cable to the speaker and the other
end to an audio source. The tracks from the
audio source can be heard through the
speaker.
HDMI (ARC) Mode:
This speaker supports HDMI(ARC) with
Audio Return channel. If your TV is HDMI(ARC)
compliant, you can hear the TV Audio through
your speaker by using a Single HDMI cable, use
a high speed HDMI cable, connect the one end
of HDMI Connector to the speaker and the
other end to the TV. The HDMI (ARC) port on
the TV might be labeled differently. For details,
See the TV's user manual. Use either the
buttons on the speaker or the Input button on
the remote control to switch to “HDMI (ARC)”
mode. After successfully connected, the LED
get display.
Note: Playback functions (play/pause, tracks) cannot be
adjusted through the speaker remote when in ARC mode.
Optical Mode:
Use this Input mode to play music from
the optical digital output for example from a TV
on your speaker. The TV must have an optical
digital output. Use the optical cable to make
the connection.
Connect the one end of the optical cable
to the optical digital output of your TV and the