Zennio LUMENTO X3 Guide

LUMENTO X3
LED DIMMING
RGB CONTROLLER
ZN1DI-RGBX3 Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 7 For further information www.zennio.com Page. 1of 2
FEATURES
Control of RGB LED or 3 independent channels.
External power supply required (12 or 24 VDC).
LED test function.
Integrated KNX BCU.
Conformity with the CE directives.
1. KNX
connector
2. KNX programming and
internal test LED
3. KNX programming
button
4. Test button
5. LED control
terminal block
6. External
power supply
7. Test and reversed
polarity indicator LED
GENERAL SYSTEM SPECIFICATIONS
Type of device
Electric operation control device
KNX supply
Voltage (typical)
29VDC
Voltage range
21…31VDC
Power consumption
145mW
Connection type
Typical bus connector TP1, 0.80mm2 section
External power supply
12 or 24V DC
Power supply cable section
1.5 to 2.5mm²
Type of control
PWM (150, 300, 488 or 600 Hz)
Operation temperature
0ºC to +45ºC
Storage temperature
-5ºC to +50ºC
Operation humidity
30 to 85% RH (no condensation)
Storage humidity
30 to 85% RH (no condensation)
Complementary characteristics
Class B
Protection class
II
Operation type
Continuous operation
Device action type
Type 1
Electrical stress period
Long
Degree of protection
IP20, clean environment
Installation
Surface installation independent device.
Connect LUMENTO as near as possible to both, the LED to dimmer and the external power supply
Response on KNX bus failure
Data saving
Response on KNX bus restart
Data recovery
PCB CTI index
175 V
Housing material
PC-ABS FR V0 halogen free
Dimensions
Without terminal blocks: 144x44x22mm / With terminal blocks: 157x44x22mm
Weight
104g
Operation indication
Programming/internal test LED indicates: programming mode (red lighting), safe mode (red
blinking) and internal test (blue blinking).
Test LED indicates: white, device in test mode; red, test channel 1 (R); green, test channel 2 (G);
blue, test channel 3 (B). Reverse polarity of external power supply is indicated by the test LED with
orange light.
KNX programming button: short button press to set the programming mode. If this button is held while plugging the device to
the KNX bus, it enters into safe mode.
KNX programming and internal test LED: the red LED indicates programming mode. When the device enters into safe mode,
it blinks red every 0.5 seconds. The blinking blue LED indicates internal test.
Test button: it tests the functioning of channels connected to the device. Push and hold for 3 seconds to get in/out of the testing
mode.
Test LED and polarity: tricolored LED that indicates which channel (red=channel 1/R, green=channel 2/G, blue=channel 3/B) is
being tested. Orange light indicates reverse polarity in external power supply.
3
3
4
5
7
2
1
6
Figure 1. LUMENTO X3

LUMENTO X3
LED DIMMING
RGB CONTROLLER
ZN1DI-RGBX3 Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 7 For further information www.zennio.com Page. 2of 2
WIRING AND ASSEMBLY DIAGRAMS
Recommended installation: NOT recommended:
Vertical position.
If there is not any
other possibility,
install terminal block
up (see fig.)
OUTPUTS SPECIFICATIONS AND CONNECTIONS
Maximum current per channel
2.5A @ 25ºC ambient temperature
Number of channels
3
Total power connected
90W (12VDC) or 180W (24VDC)
Connection type
Pluggable screw terminal block
Cable section
1.5 to 2.5mm²
Load type
Common anode
Shortcut protection
Yes
Overheating protection
Yes
LED
The LED load is connected to the terminal block, matching the anode or the anode common terminal of the
LED stripes with C (anode). The cathode terminal can be connected to several output channels in case of
necessity of more than 2.5A (up to 7.5A) of supply to LED strip, keeping the same section and length of
cables from output to LED strip.
Correspondence
C: Anode 1: Red 2: Green 3: Blue 4: -spare-
Assembly:
Screw mounting, 2 holes of
3.5mm diameter. Screws
not included.
External power supply:
+ and - terminals of
external power supply 12
or 24 VDC
SAFETY INSTRUCTIONS
Installation should only be performed by qualified professionals according to the laws and regulations applicable in each
country.
Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the
entire KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the
wires of other accessories, in case of being installed.
Once the device is installed, it must not be accessible from outside.
Keep the device away from water and do not cover it with clothes, paper or any other material while in use.
The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the
instructions at http://zennio.com/weee-regulation.