SKYDANCE KL User manual

Output current Max 1.5A (AC)
Input voltage AC100-240V
Output voltage AC100-240V
User Manual Ver 1.0.6
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Dimming data
Dimming range
Rotary knob + RF 2.4GHz
30m
256 levels
0 -100%
Technical Parameters
Input and Output
Safety and EMC
EMC standard (EMC)
EN 55015:2013
EN 61547:2009
EN 61000-3-2:2014
EN 61000-3-3:2013
Certification CE,EMC,LVD
EN 61347-2-11:2002
EN 61347-1:2015
EN 62493:2015
Safety standard(LVD)
Warranty
5 years
Warranty
Input signal
RF Control distance
Dimming level
Ta: -30
O
C ~ +55
O
C
T c: +65
O
C
Model No.: KL
Rotary dimming/AC relay output/Wireless remote control
Features
Page 1
Mechanical Structures and Installations
0-10V Rotary Panel Dimmer
LVD
● Rotary panel 0-10V dimmer, 1 channel output.
● Output 1 channel 0-10V signal,
connect with 0/1-10V dimmable driver.
● High voltage AC input, High voltage AC relay output.
● Rotate knob to change brightness,
support push and long push operation.
Skydance’s 2.4G dimming remote control● Compatibility with .
86 . 00 mm
86 . 00 mm
48 . 50 mm
KL 0-10V Rotary Panel Dimmer
AC L input
AC N input
AC N output
AC L output
0-10V signal output
GND
Wiring diagram
Output signal 0-10V (20mA)
● Connect with 0/1-10V dimming driver (no use AC OUT)
26 m m
51 . 50 mm
51 . 50 mm
AC110-220V
V+
V-
DI M+
DI M-
AC N
AC L +Single color LED strip
0/1-10V
Dimmable Driver
Weight
0.100kg
Gross weight
Net weight
0.160kg

● Push: Turn on or off light.
After turn on light:
● Rotate: Rotate knob to adjust brightness, 2.5 turns, 50 levels.
● Long push(1-6s): Continuous 256 levels brightness adjustment.
Knob function
Causes
1. The batter y has no power.
2. Beyond controllable distance.
3. The controller did not match the remote.
1. No power.
2. Wrong connection or insecure.
Malfunctions
No response
from the remote
No light
Malfunctions analysis & troubleshooting
Troubleshooting
1. Replace battery.
2. Reduce remote distance.
3. Re-match the remote.
1. Check the power.
2. Check the connection.
Match Remote Control (two match ways)
Use Power Restart
Match:
Switch off the power, then switch on power again, immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power again, immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.
End user can choose the suitable match/delete ways. Two options are offered for selection:
Match:
Turn on light, turn off, immediately push the knob for 5s, immediately press on/off key(single zone remote)
or zone key(multiple zone remote) of the remote.
The 0-10V rotary panel dimmer can also match with the RF dimming remote (optional).
Use Knob
Delete:
Turn on light, turn off, immediately push the knob for 10s, delete all matched remotes.
User Manual Ver 1.0.6 Page 2
● Connect with 0/1-10V dimming driver (use AC OUT)
KL 0-10V Rotary Panel Dimmer
AC110-220V
V+
V-
DI M+
DI M-
AC N
AC L +Single color LED strip
0/1-10V
Dimmable Driver
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,
The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
● Connect with 0/1-10V dimming driver (use AC OUT and relay or contactor)
An additional AC relay or contactor is needed when total input current of the load is higher than 1.5A
or inrush current is greater than 15A.
AC110-220V
V+
V-
DI M+
DI M-
AC N
AC L
+Single color LED strip
0/1-10V
Dimmable Driver
Relay or
Contactor