Zenno SS40E User manual

Brushless DC Tubular Motor
Operation Manual
Tubular Motor Type
：
SS40E
Remote Control Type：ZEN16SA、ZEN16DA

- 2 -
Table of Content
Before Using
Safety recautions
3
Name of Each Part
4
Installation 7
Settings
Switch Setting Mode / User Mode
11
Switch blind system
13
Set Connection Between Motor and Remote Control
14
Cancel the Connection
15
Switch Between Forward and Reverse Rotations
16
Set Upper and Lower limits
17
Set Group Control 19
Duplicate Remote Control 21
Cancel『
Other
』Remote Control
22
Set \ Cancel Preferred Position 23
Operate Preferred Position
24
Quick Command Guide
25
Miscellaneous
Troubleshooting
27
Illustration of Wiring 28
Appendix 29

- 3 -
Before using this product , please read the manual carefully.
After reading , please keep this manual properly for future reference.
In this manual, the precautions indicated as Warnings and Cautions. Please observe the
following precautions to ensure safety.
Warning
This indicates " Possible death or serious injur
y
may occur ".
Caution
This indicates " Possible injury or material damage
may occur".
Warning
The appliance is not to be used by children or persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction.
Children being supervised not to play with the appliance.

Important safety instructions. Follow all instructions, since incorrect installation can lead
to severe injury.
Do not allow children to play with fixed controls. Keep remote controls away from
children
Frequently examine the installation for imbalance and signs of wear or damage to
cables
and springs. Do not use if repair or adjustment is necessary.
Full all-pole disconnection from the supply mains must be provided in the
fixed wiring in accordance with the wiring rules.
Caution
To reduce the fire risk of electric shock or product damage:
Do not expose the equipment to rain, moist, water dripping or water splashing
environment; and do not place objects fully filled with water next to the equipment.
Do not disassemble this equipment.
Do not use any power supply with a voltage not complying with the rated voltage of the
equipment.
If there is any abnormal condition or when it needs repair, please contact your
distributor or the original dealer.
If you find any errors in this manual, or if you are not clear about the
description in this manual, please contact the distributor. Thank you!
Safety Precautions
！
！
！
！

- 4 -
SS40E series Tubular Motor
1. Driving Wheel：
It connects the tubular motor to the aluminum tube so that the motor may drive the aluminum tube
to rotate.
2. Code Button：
It is for setting the communication code between the remote control unit and the tubular motor.
3. Crown
4. Antenna：
It is for receiving instructions from the remote control unit.
5. AC Power Cord
Name of Each Part
1
2
3
4
5

- 5 -
ZEN16SA remote control
Front side details
1. LCD Screen：
A. Group channel : 4 group control channels available from G1 to G4.
B. Window channel: 16 window channels available from 1 to 16.
C. All: to control all channels at the same time.
D. Battery: appears only low battery.
E. OK: a confirm key during group control settings.
F. Window number frame selection: the currently promoted window number.
2. Channel selection buttons「」、「 」、「 <」、「>」:
To select window channel or group channel or All.
3. ENTER :：
To confirm channel selected.
4. UP :：
To lift blinds upward.
5. STOP：
To stop blinds movement, or move blinds to preferred position, or switch between forward and
backward rotations.
6. DOWN：
To move blinds downward.
1
4
5
6
2 3
2
A
D
B
C
E
LCD Screen detail
F

- 6 -
Reverse side details
1. Duplicate button：
2. To duplicate or cancel the remote control
3. Mode switch：
To switch between USER MODE and SETTING MODE。
4. Battery cover
※Notice:
About the remote control:
Please do not install the socket at a location that may be exposed to direct sunlight.
If the Remote Control activates other electronic appliances, please contact the distributor.
Caution:
FCC ID: YUYSSRC002
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
2
1
3

- 7 -
1. Select a suitable aluminum tube
2. Insert the tubular motor into tube
Installation

Installation of motorized blinds
：
Cylindrical
Aluminum Tube
Inside d iameter φ40
Slot size
13
㎜
5
㎜
Molded
Aluminum Tube
ATD46
Molded
Aluminum Tube
ATD50
A"plastic ring for ATD50" is
required
Molded
Aluminum Tube
ATD51
A" ring for ATD51" is
required
Molded
Aluminum Tube
ATO43
Specified tube for
venetian blinds

- 8 -
3. Position the Crown pin into the slot.
4. Fasten the tube at the motor end with screws (not a necessity, may
skip this step)
5. Inset the idler wheel onto tube.
Cylindrical
Aluminum Tube
Molded
Aluminum Tube
Position for inserting the Positioning Pin of the Crown
Positions for
mounting the
screws

- 9 -
6. Fasten the tube at the idler wheel end with screws (not a necessity,
may skip this step).
7. Install the brackets:Measure a suitable distance for installing the brackets to the target
position (in the curtain box or on the wall).
8. Install the motorized blinds: Install the motorized blinds onto the brackets.
9. Connect to the electric power: Connect power cord to AC power before setting and
operation.。
Positions for
mounting the
screws
Notice！The positioning slot should be
firmly fixed into the bracket.

- 10 -
Screen display sequences after installing battery

Battery installation
1
3
2
1. Open the battery cover
2. Insert the battery (notice the polarity ○
＋/○ －)
3. Close the battery cover
4. Battery specification: DC 6V (CR2032)
3.1 In Setting Mode:
only Window Channels
1 ~ 16 appear.
1. All icons appear
after installing battery
2. Battery icon flashes 2
times than disappear,
remote control is ready
for using after battery
icon disappear.
3.2 In User Mode:
appear Group
Channels, Window
Channels, and All.
5.Low battery
It could not do settings
while the battery icon
flashes,please change a
new one immediately
4. If [All] is selected,
Group Channels and
Window Channels will
disappear.
About the battery
The battery provided with the product is prepared for your initial
use.
For the battery replacement, please use a battery with the same
specifications.
If the remote control is not going to be used for a long time, please
take the battery out.
※Notice:

- 11 -
1. Please switch the remote control to【Setting Mode】when the motor needs
settings, and switch to【User Mode】when the motor is ready to be operated.
2. To switch between【Setting Mode】and【User Mode】should be achieved
on the remote control.
3. Mode check：
the screen appears Group Channels G1~
G4, Window Channels 1~16, and All
Switch Setting Mode / User Mode
【
Setting Mode
】【
User Mode
】
The LCD screen appears Window
Channels 1~16

- 12 -
4. Mode Switch：
Open the battery cover on the remote control.
Toggle the【Mode Selection Switch】located above the battery.
Note: It is necessary to use a thin rod to toggle the switch.
After finish toggling【Mode Selection Switch】, close the battery cover
immediately.
※
Notice:
Unless the motor requires reset, please keep the
【
Mode Selection Switch
】
in
【
User Mode
】
.
Schematic Diagram of
Mode Selection Switch
Setting Mode
The switch is at
the right position
User Mode
The switch is at
the left position
3. After the mode selection is
completed, close the b
attery
cover immediately.
1. Open the battery cover.
2.
Toggle the Mode Selection Switch

- 13 -
1. The tubular motor could operate either【Roller system】or【Venetian system】.
【Roller system】:It could not adjust by degrees on User Mode, but only could on Setting Mode.
【Venetian system】:It could adjust by degrees both on User Mode and Setting Mode.
2. How to switch:
Switch the remote control to【Setting Mode】.
To enter【Roller system】, press both【UP】&【Enter】for 2 seconds until the cursor [ ] lit.
To enter【Venetian system】, press both【DOWN】&【Enter】for 2 seconds until the cursor [ ]
lit.
Press the
【
Up
】
button
and【Enter】button
simultaneously
Press the
【
Down
】
button
and【Enter】button
simultaneously
Roller system
（
Default
）
Venetian system
Switch blinds system
※
Notice:
Once the system has been chosen, all channels are in the same system.
Roller System is the initial setting from factory.

- 14 -
1. Switch the remote control to【Setting Mode】。
2. Channel Selection:
Press any button of「」、「 」、「 <」、「 >」to select the channel needs to be
connected.
3. Code:To establish a connection between the motor and the remote control.
Press【Code】on the motor for 1 second, the motor will respond “beep “.
Set Connection Between Motor
and Remote Control
Press the【Code】to start code identification.
Press any button of【】
、【

】、
【
＜
】、【
＞
】to move cursor [ ]
to the target channel

- 15 -
Press【Up】and【Down】simultaneously ; when the motor responds with a “beeping” sound, the
code identification process is complete and the remote control is ready to control this motor.
1. Cancel Connection：Press【Code】on the motor for 5 seconds; when the motor
responds with a “beeping” sound, the connection to all remote controls has been
cleared.
Beep
Press【
Code
】for
5
seconds to cancel the connection.
※
Notice:
Unless it is necessary to establish connection again, please do not press the【Code】for more than
2
seconds.
To avoid interference, please set the connection one by one in the same building.
Cancel Connection
Press the【Up】
and
【
Down
】
simultaneously

- 16 -
1. Switch the remote control to【Setting Mode】。
2. Switch Between Forward and Backward Rotations：
Press【Stop】for 3seconds; when the motor responds with a “beeping” sound, the
process for switching between forward and backward rotation is complete.
Switch Between Forward and Backward
Beep

Press
【
Stop
】
for 3seconds.
※
Notice:
Unless it is necessary to change the rotation direction , please do not press【Stop】for more than
3
seconds.
It requires to reset the upper/lower limit again if the rotation direction has been changed after the
setting of upper/lower limit is complete.

- 17 -
1. Switch the remote control to【Setting Mode】。
2. Enter the Upper Limit Setting Mode:
Press【Up】and【Stop】simultaneously; when the motor responds with a “beeping”
sound, it enters the Upper Limit Setting Mode.
3. Set the Upper Limit:
Use remote control to lift blinds at the target position for setting the upper limit.
During this operation, please perform【Switch Between Forward and Backward
Rotations】if necessary.
Press【Stop】and【Enter】simultaneously; when the motor responds with a
“beeping” sound, the upper limit setting is complete.
Set Upper/Lower Limit
Press【Stop】
and
【
Enter
】
simultaneously
Beep
Press【Up】and【Stop】
simultaneously.
Beep

- 18 -
4. Enter the Lower Limit Setting:
Press 【Stop】and【Down】simultaneously; when the motor responds with a
“beeping” sound, it enters the Lower Limit Setting Mode.
5. Set the Lower Limit:
Use remote control to lift blinds at the target position for setting the lower limit.
Press【Stop】and【Enter】simultaneously; when the motor responds with a
“beeping” sound, the lower limit setting is complete.
6. If need to reset the upper/lower limit again, please repeat『Step 2~3』or
『Steps 4~5』.
※
Notice:
After the
【
Upper/Lower Limit Setting
】
is complete, please toggle the
【
Mode Selection Switch
】
back to【User Mode】.
If need to reset the limit position, either upper limit setting or lower limit setting could be executed
separately.
Press
【
Stop
】
and
【
Down
】
simultaneously
Beep
Press【Stop】and
【
Enter
】
simultaneously
Beep

- 19 -
1. Switch the remote control to【User Mode】。
2. Select Group:Press any button of 「」、「 」、「 <」、「 >」to move cursor [ ] to
the target group channels G1 ~ G4 which needs to be executed. The
ZEN16SA remote control provides up to 4 groups to perform.
3. Enter group setting:Press【Enter】for 3 seconds to enter group setting.
Set Group Control
Press【Enter】
for 3 sec.
Select group
Select target group,then the
selected group channel is flash.
Press any of them
to move cursor
Enter group setting
Press
【
Enter
】
for 3 seconds
until the group icon G2~G4
disappear, and G1 is flash.

- 20 -
4. Select window:Press any button of 「」、「 」、「 <」、「 >」to move cursor [ ] to
the target window.
5. Join window:Press【Enter】to join window in this group and the cursor [ ] will
stay on the window once it is joined, another flash cursor [ ] will be
stand by after the previous window is joined.
6. Confirm group:Once all windows are selected and joined, move cursor [ ] to OK
and press【Enter】to complete the group setting。
7. To add or to remove window from a group:
Follow by the above step 1 to step 4 , press 【Enter】to join the new window, and
the cursor [ ] stay on the new joined window. Press 【Enter】to remove the joined
window, the cursor [ ] become flash on the removed window。
Join windows in the group
Press【Enter】to join window in
this group.
Confirm group
Move cursor to OK and
press
【
Enter
】
Group setting complete
The
group icon is flash after
group setting complete. Only
joined windows appear under
this group icon.