LITHIUM-ION LED FLASHLIGHT
INSTRUCTION MANUAL
LINTERNA LED DE LITIO-ION
MANUAL DE INSTRUCCIÓN
TL1KPZ
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.
Copyright / Derechos Reservados © 2014
Baccus Global LLC, Boca Raton, FL 33432
(877) 571-2391
BC
2
3
5
1 1
4
10
6
11
8
9
7
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void user’s
authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating flashlight. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to
the State of California to cause cancer and birth defect or other reproductive harm.
Wash hands after handling.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
• To reduce the risk of injury, close supervision is necessary when the flashlight is
used near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Charge indoors only.
• Do not expose charging adapters or battery to moisture, water or any other
liquid.
• Use only the charging adapter supplied by the manufacturer to recharge.
• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord
should be at least as great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or
tabletop where it can be tripped over, snagged, or pulled on unintentionally
(especially by children).
– The extension cord should be kept dry and off the ground.
WARNING: FIRE HAZARD: Keep flashlight lamp away from materials that may
burn.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• The LED gets hot quickly. Do not touch the hot lens, guard or enclosure.
• Never place the light face down on any surface when lit, charging or not in use.
Never store the light face down on any surface.
• Never look directly into the light or shine the light into another person’s eyes.
• Keep sharp objects away from lens — it can crack or break.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw flashlight. It contains a lithium-ion battery pack.
• Use only with either the AC or DC charging adapter and/or the USB charging
cable that are provided with unit. Plug in the charging cable at the flashlight first,
then plug into the charging source.
• Do not overcharge: Recharge up to 4 hours maximum or until the charge status
LED indicator lights blue.
• After charging/recharging, disconnect charging adapter and wait 5 minutes before
use.
• Do not crush, cut, pull or expose the charging cable to extreme heat.
• Position the charging cable so it does not become entangled or become a safety
hazard. Keep the charging cable away from sharp edges.
• Do not open the flashlight body casing. There are no user-serviceable parts inside.
• Do not operate the flashlight without the lens in place.
• To reduce risk of damage to the charging cable, pull by the plug rather than the
cord when disconnecting.
• Do not attempt to charge the unit if the charging adapter is damaged – return
the charging adapter to manufacturer for repair or replacement.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION BATTERIES
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST
HAZARD, OR INJURY TO PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power
to this unit. However, they must be used and charged properly. Improper use can
result in serious injury, fire, or death.
• Lithium-ion batteries can explode in the presence of a source of ignition. Do not
use the product in the presence of an open flame.
• Do not place this lithium-ion battery powered unit in fire or apply heat to it.
• Do not subject this lithium-ion battery powered unit to strong impacts or shocks.
The battery in this unit contains safety and protection devices which, if damaged,
may cause the battery to generate heat, rupture or ignite.
• Do not expose the lithium-ion battery to water or salt water, or allow the battery
to get wet.
• Avoid storing this lithium-ion battery powered unit in the basement, bathroom
or other areas of the house that are or may become wet or where humidity and
moisture may concentrate.
• Do not leave this lithium-ion battery powered unit in direct sunlight, or use
or store the unit inside cars in hot weather. Doing so may cause the battery to
generate heat, rupture, or ignite. Using the battery in this manner may also result
in a loss of performance and a shortened life expectancy.
• Never charge this unit near heat or flammable objects.
• NEVER THROW WATER ON A BURNING LI-ION BATTERY! If a lithium-ion
battery does catch on fire, it will burn even more violently if it comes in
contact with water or even moisture in the air. A fire extinguisher must
be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before
using it for the first time.
When stored at room temperature with a full charge, Li-ion batteries will begin to
discharge from the time they are manufactured, even when unused. Deep discharges
also decrease their capacity. Battery life can be extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent
overdischarge.
Transportation of Lithium-Ion Batteries
• Always check all applicable local, national, and international regulations before
transporting a unit containing a Lithium-Ion battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be
specifically limited or prohibited.
INSTRUCTIONS PERTAINING TO WATERPROOF FLASHLIGHTS
The rubber O-ring acts to preserve the waterproof qualities of the flashlight. The
O-ring seals the charging port cover to prevent water from entering the gap. An
undamaged rubber O-ring and lens, and proper sealing of the charging port cover
before use are very important.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Attempting to remove the rubber O-ring, use of the unit with a damaged
O-ring or lens, improper sealing of the waterproof charging port cover, and/
or submerging this unit in water deeper than 1 meter, for time longer than 30
minutes and/ or in temperatures other than between 41ºF and 104ºF (5ºC and
40ºC), may cause the unit to no longer be waterproof. Do not use the unit if these
conditions exist or it could sustain permanent damage.
INSTRUCTIONS PERTAINING TO THE USB PORTS
• IMPORTANT: Some household USB-powered electronics will not operate with
the USB ports provided with this device. Check the manual of the corresponding
electronic device to confirm that it can be used with this type of USB port.
• The USB ports do not support data communication. They only provide
power to an external USB powered device (5V DC/1A using the flashlight’s USB
port or 5V DC/2A using the USB ports on the AC or DC charging adapters). Make
sure the rating of equipment plugged into the each USB port does not exceed the
amperage stated.
• Do not attach USB hubs allowing connection of multiple personal electronic
devices to any of these USB ports on the flashlight or charging adapters.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Zero Trace™ Lithium-Ion LED
Flashlight.Read this Instruction Manual and follow the instructions
carefully before using your new flashlight.
FEATURES
1. Charging port cover
2. Power/light mode button
3. USB port (for use with USB charging cable and charging adapters)
4. Battery/charge status LED indicator / translucent USB power button
5. Rubber O-ring
6. USB charging cable (for use with 120 volt AC/USB and 12 volt DC/USB charging
adapters)
7. 12 volt DC/USB charging adapter
8. 12 volt DC/USB charging adapter LED Indicator
9. 12 volt DC/USB charging adapter USB port
10. 120 volt AC/USB charging adapter
11. 120 volt AC/USB charging adapter USB port
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery/charge status LED indicator is located inside the translucent USB Power
Button. It lights or flashes in three colors to indicate the following:
When charging:
Blue: Battery is in a fully charged state.
Yellow (flashing): Battery is in a partially charged state.
Red (flashing): Battery needs to be recharged.
When operating the USB port (once the translucent USB power button has
been pressed):
Blue: Battery is operating at full voltage.
Yellow: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged.
Red (flashing): Battery is operating at extremely low voltage. The built-in low
voltage protection has activated and the unit will automatically shut down. The unit
must be recharged immediately.
CHARGING/RECHARGING THE FLASHLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and
BEFORE first use using the 120 volt AC/USB charging adapter for up to 4 hours or
until the battery/charge status LED indicator lights blue.
Recharge after each use until the charge status LED indicator lights blue.
IMPORTANT: When the unit is not in use, we recommend that the battery is
charged at least every 3 to 6 months.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Never place the light face down on any surface when charging.
• Make sure the flashlight is turned OFF during recharging, as operating the
flashlight can slow the recharging process.
• Failure to keep the battery charged will cause permanent damage and result in
poor performance.
Charging/recharging using the 120 Volt AC/USB Charging Adapter
1. Make sure the power mode button and the translucent USB power button
are both turned off* (the flashlight is not lit and the translucent USB power
indicator/ power button is not lit).
* The translucent button does not operate the flashlight, only the USB power
port.
2. Unscrew the charging port cover (counterclockwise) until the USB port is
exposed.
3. Insert the USB charging cable into the USB port on the flashlight.
4. Insert the other end of the USB charging cable into the 120 volt AC/USB
charging adapter.
5. Plug the 120 volt AC/USB charging adapter into a (powered) standard North
American 120 volt 60Hz outlet. The battery/charge status LED indicator will light
or flash in one of three colors (as described in the “Reading the Battery/Charge
Status LED Indicator” section) to indicate the charging status.
6. Charge up to 4 hours or until the battery/charge status LED indicator lights blue.
7. When charging is complete, first unplug the AC/USB charging adapter from the
power source, then disconnect the USB charging cable from the adapter and
the flashlight. Store the adapter and cable in a safe place.
8. Screw the charge port cover back in place (clockwise) until it is finger right.
Make sure it fits securely, but do NOT overtighten.
Charging/recharging using the 12 Volt DC/USB Charging Adapter
1. Make sure the power mode button and the translucent USB power button
are both turned off* (the flashlight is not lit and the translucent USB power
indicator/ power button is not lit).
* The translucent button does not operate the flashlight, only the USB power
port.
2. Unscrew the charging port cover (counterclockwise) until the USB charging port
is exposed.
3. Insert the USB charging cable into the USB port on the flashlight.
4. Insert the other end of the USB charging cable into the 12 volt DC/USB charging
adapter.
5. Insert the 12 volt DC/USB charging adapter into the 12 volt DC accessory outlet
of a vehicle or other functioning 12 volt DC power source. The LED indicator
on the 12 volt DC/USB charging adapter will light green when it is properly
plugged into the 12 volt DC power source. The battery/charge status LED
indicator will light or flash in one of three colors (as described in the “Reading
the Battery/Charge Status LED Indicator” section) to indicate the charging
status.
Note: Some vehicles require that the ignition be switched to the accessory position
in order to power the accessory outlet.
6. Charge up to 4 hours or until the battery/charge status LED indicator lights blue.
7. When charging is complete, first unplug the 12 volt DC/USB charging adapter
from the 12 volt DC power source, then disconnect the USB charging cable from
the adapter and the flashlight. Store the adapter and cable in a safe place.
8. Screw the charge port cover back in place (clockwise) until it is finger right.
Make sure it fits securely, but do NOT overtigthten.
CAUTION: TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC charging adapter must only be connected to batteries with a
nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery
and will sustain permanent damage if connected to a 24 volt battery.
Charging/recharging using the USB charging cable and a device with a
USB power port (not supplied)
1. Make sure the power mode button and the translucent USB power button
are both turned off* (the flashlight is not lit and the translucent USB power
indicator/ power button is not lit).
* The translucent button does not operate the flashlight, only the USB power
port.
2. Unscrew the charging port cover (counterclockwise) until the USB charging port
is exposed.
3. Insert the USB charging cable into the USB port on the flashlight.
4. Insert the other end of the USB charging cable into a device’s functional USB
power port. The battery/charge status LED indicator will light or flash in one
of three colors (as described in the “Reading the Battery/Charge Status LED
Indicator” section) to indicate the charging status.
5. Charge until the battery/charge status LED indicator lights blue.
6. When charging is complete, disconnect the USB charging cable from the
device’s USB power port and the flashlight. Store the cable in a safe place.
7. Screw the charge port cover back in place (clockwise) until it is finger tight.
Make sure it fits securely, but do NOT overtigthten.
OPERATING THE FLASHLIGHT
The power/light mode button is located at the bottom of the flashlight. It turns
the flashlight on and off; and is also used to select high (bright), low (dimmer) and
flashing (SOS) modes.
Notes: The battery/charge status LED indicator will not light during cordless operation of
the flashlight.
To check the battery status, make sure the flashlight is turned off, then press on
the translucent USB power button. The battery/charge status LED indicator will
light or flash in one of three colors (as described in the “Reading the Battery/
Charge Status LED Indicator” section) to indicate the internal battery status.
The battery/charge status LED indicator will automatically turn off if it detects
there is no USB output power for 10 seconds.
IMPORTANT: Never attempt to operate the flashlight’s USB port and the flashlight
simultaneously.
Operating the flashlight cordless
Disconnect the charging cable or adapter, then select the light mode as follows:
FOR HIGH (BRIGHT) MODE:
1. Press the power/light mode button firmly (a “click” will sound). The flashlight is
now operating at its highest (brightest) setting.
2. Press the power/light mode button firmly again (a “click” will sound) to turn
the flashlight off.
FOR LOW (DIMMER) MODE:
1. Press the power/light mode button firmly (a “click” will sound).
2. Press the power/light mode button gently once (no “click” will sound). The
flashlight is now operating at its lowest (dimmer) setting. Gently press it twice
more to return to high (bright) mode.
3. Press the power/light mode button firmly again (a “click” will sound) to turn
the flashlight off.
FOR FLASHING (SOS) MODE:
1. Press the power/light mode button firmly (a “click” will sound).
2. Press the power/light mode button gently twice (no “click” will sound). In
this mode, the light will repeatedly emit the SOS signal (a continuous sequence
of three short flashes/three longer flashes/three short flashes). Gently press it
once again to return to high (bright) mode.
3. Press the power/light mode button firmly again (a “click” will sound) to turn
the flashlight off.
IMPORTANT: If the flashlight battery voltage is low, it may operate in low (dimmer)
mode even when the power/light mode button is pressed only once. The built-in
low voltage protection will activate after a short period of operation, then the unit
will automatically shut down This is a special feature to protect the unit’s internal
battery from damage. Recharge the battery before continuing use.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE: Make sure the
flashlight’s USB port is turned off (the battery/charge status LED indicator is not lit)
during operation.
Operating the flashlight corded
Attach the appropriate cable or adapter as described in the “Charging/Recharging”
section. Operate normally the flashlight as outlined in the previous section.
IMPORTANT: The flashlight will operate while either charging adapter or the USB
cable is attached, but will continue to draw power from the unit’s Lithium-Ion
battery while the flashlight operates. This may cause the low voltage protection to
activate and shut the flashlight down. Manufacturer recommends only operating
the unit in corded mode for a short period of time.
OPERATING THE FLASHLIGHT’S USB PORT
The flashlight’s USB port is located under the charging port cover. It provides 5
volts/1A of DC power to an external USB powered device.
1. Disconnect the charging adapter or cable and make sure the flashlight is turned
off.
2. Unscrew the charging port cover (counterclockwise) until the USB port is exposed.
3. Press the translucent USB power button to power on the USB port. The
battery/charge status LED indicator will light or flash in one of three colors (as
described in the “Reading the Battery/Charge Status LED Indicator” section) to
indicate the internal battery status.
4. Simply plug the USB device into the flashlight’s USB port and operate normally.
5. Press the translucent USB power button again to turn off the USB port. Make
sure the translucent USB power button is in the off position (is not lit) when the
unit is being recharged or stored.
6. Screw the charge port cover back in place (clockwise) until it is finger tight.
Make sure it fits securely, but do NOT overtigthten.
Note: The flashlight’s USB port will automatically shut down (the battery/charge status
LED indicator will automatically turn off) if it detects there is no USB output
power for 10 seconds.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Do not simultaneously operate the flashlight and the flashlight’s USB port.
OPERATING THE 120 VOLT AC/USB CHARGING ADAPTER’S
USB PORT
Plug the 120 volt AC/USB charging adapter into a (powered) standard North
American 120 volt 60Hz outlet. Then simply plug the USB device into the USB outlet
and operate normally.
WARNING: TO AVOID THE RISK OF PROPERTY DAMAGE:
• Always plug the 120 volt AC/USB charging adapter to the standard North
American 120 volt 60Hz outlet before plugging any devices into it.
OPERATING THE 12 VOLT DC/USB CHARGING ADAPTER’S
USB PORT
Plug the 12 volt DC/USB charging adapter into a vehicle’s 12 volt DC accessory outlet
or other functioning 12 volt DC power source. The LED indicator on the 12 volt DC/
USB charging adapter will light green to indicate that it is properly connected. Then
simply plug the USB device into the USB outlet and operate normally.
WARNING: TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 volt DC/USB charging adapter must only be connected to batteries with a
nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery
and will sustain permanent damage if connected to a 24 volt battery.
• Always connect the 12 volt DC/USB charging adapter to the 12 volt DC power
source before plugging any devices into it.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is
charged at least every 3 to 6 months.
If the unit gets dirty, gently clean the outer surfaces of the flashlight unit with a soft
cloth moistened with a mild solution of water and detergent.
Except for the fuse in the 12 volt DC/USB charging adapter, there are no user-
replaceable parts. Periodically inspect the condition of adapters, connectors and
wires. Contact manufacturer to replace any components that have become worn or
broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a
number of factors including but not limited to the number of recharge cycles, and
proper care and maintenance of the battery by the end user. Contact manufacturer
for any information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of properly.
Recycling is required. Failure to comply with local, state and
federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
Fuse replacement in the 12 volt DC/USB charging adapter
2A FUSE
CENTER CONTACT
END CAP
1. Unscrew the end cap
counterclockwise and remove.
2. Remove center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 2
amp fuse.
5. Replace the fuse, center contact and
end cap.
6. Screw end cap clockwise until it
is finger tight - DO NOT OVER-
TIGHTEN.
7. Test for proper operation of the 12
volt DC/USB charging adapter.
TROUBLESHOOTING
The flashlight will not charge
• Check that the translucent USB power button is turned off.
• Check the connection to the AC or DC power source. Make sure there is good contact.
• Confirm that there is functioning AC or DC current.
The flashlight will not operate cordless
• Make sure the power/light mode button has been pressed firmly (and that you
hear a distinct “click”) to turn the flashlight on.
• Check that the translucent USB power button is turned off.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
The flashlight’s USB port will not operate
• Make sure the cable and/or adapter is disconnected from any live AC or DC power
source.
• Make sure the power/light mode button is turned off.
• Make sure the translucent USB power button is pressed to turn the USB port on.
• The flashlight’s USB port will automatically shut down (the battery/charge status
LED indicator will automatically turn off) if it detects there is no USB output
power for 10 seconds. Press the translucent USB power button again to turn the
flashlight’s USB port back on.
• Make sure the rating of equipment plugged into the flashlight’s USB port does
not exceed 1A continuous.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
The 120 volt AC/USB charging adapter’s USB port will not operate
• Make sure you have live AC power to the outlet the 120 volt AC/USB charging
adapter is plugged into.
• Make sure the rating of equipment plugged into the charging adapter’s USB port
does not exceed 2A continuous.
The 12 volt DC/USB charging adapter’s USB port will not operate / LED
indicator on the 12 volt DC/USB charging adapter does not come on
• Check the connection to the 12 volt power source. Make sure there is good contact.
• Confirm there is functioning DC current.
• The fuse inside may have blown. Replace the fuse following the instructions in
this manual.
• Make sure the rating of equipment plugged into the charging adapter’s USB port
does not exceed 2A continuous.
If the unit does not operate after taking the steps given above, contact the
manufacturer at (877) 571-2391.
ACCESSORIES
Recommended accessories for use with this unit may be available from the
manufacturer. If you need assistance regarding accessories, please contact
manufacturer at 1-877-571-2391.
WARNING: The use of any accessory not recommended for use with this
appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the manufacturer at 877-571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and
workmanship for a period of ONE (1) YEAR from the date of retail purchase by the
original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the
defective product can be replaced or repaired in the following ways: (1) Return the
product to the manufacturer for repair or replacement at manufacturer’s option.
Proof of purchase may be required by manufacturer. (2) Return the product to the
retailer where product was purchased for an exchange (provided that the store is a
participating retailer). Returns to retailer should be made within the time period of
the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects
resulting from normal wear and tear, accidents; damages sustained during shipping;
alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you
may have other rights which vary from state to state or province to province. This
product is not intended for commercial use.
SPECIFICATIONS
Flashlight
(Conforms to UL STD.73)
Bulb: 10 watt LED bulb
Battery: Lithium-Ion, 7.2 V DC
Input: 5V DC, 2A
USB Output: 5V DC, 1A
120 Volt AC/USB Charging Adapter
(Conforms to UL STD. 60950-1)
Input: 120V AC, 60Hz, 0.25A
Output: 5V DC, 2A
12 Volt DC/USB Charging Adapter
(Conforms to UL STD. 2089)
Input: 12V DC, 1.1A
Output: 5V DC, 2A
Fuse: 2A
Imported by Baccus Global LLC, 595 S. Federal Highway, Suite 210, Boca Raton, FL 33432
(877) 571-2391 RD110614
Este dispositivo cumple con la parte 15 de las normas de la Comisión Federal de Comunicaciones de Estados
Unidos (FCC). La operación está sujeta a las dos condiciones siguientes: (1) este dispositivo no puede causar
interferencia perjudicial y (2) este mecanismo debe aceptar cualquier interferencia recibida, incluida la
in-terferencia que puede provocar una operación no deseada.
Este equipo ha sido probado y se encontró que cumple con los límites para dispositivo digital Clase B, según
la parte 15 de las normas de la FCC. Estos límites están diseñados para brindar protección razonable contra
interferencia perjudicial en una instalación residencial. Este equipo genera, usa y puede irradiar energía en
frecuencia de radio y, si no se instala y se usa de acuerdo con las instrucciones, puede provocar interferencia
perjudicial en las comunicaciones de radio. Sin embargo, no hay garantía de que la interferencia no ocurra
en una instalación en particular. Si el equipo provoca interferencia perjudicial en la recepción de radio o
televisión, lo que se puede determinar al apagar y encender el equipo, el usuario debe tratar de corregir
la interferencia mediante una o más de las siguientes medidas:
• Cambiar la orientación o la ubicación de la antena de recepción.
• Aumentar la separación entre el equipo y el receptor.
• Conectar el equipo a un tomacorriente sobre un circuito diferente de aquel al que está conectado el
receptor.
• Consultar al vendedor o pedir la ayuda de un técnico en radio y televisión con experiencia.
Los cambios o las modificaciones no aprobados por el partido responsable de conformidad podían anular
la autoridad del usuario para funcionar el equipo.
TL1KPZ_ManualENSP_110614.indd 2 11/6/2014 10:47:28 AM
