ZERO-X ZXM-AC3 User manual

4K UHD Action Camera with Touch Screen & WiFi
USER MANUAL
ZXM-AC3

3
CONTENTS
1.0 INTRODUCTION............................................................................... 6
2.0 ABOUT THE ZXM-AC3 .................................................................... 6
3.0 WHATS IN THE BOX......................................................................... 7
4.0 COMPONENTS................................................................................. 7
5.0 GETTING STARTED ........................................................................................... 8
5.1 CHARGING THE BATTERY .................................................................9
5.2 MICRO SD CARD COMPATIBILITY.................................................. 10
5.3 TOUCH SCREEN COMPONENTS ...................................................10
5.4 POWERING ON YOUR ZXM-AC3.................................................... 10
5.5 FORMAT YOUR MICRO SD CARD...................................................11
6.0 ZXM-AC3 CONTROLS AND FUNCTIONS...................................... 12
6.1 POWER ON/OFF Button ..................................................................12
6.2 SHOOT/RECORD Button..................................................................12
6.3 ACCESSING SYSTEM SETTINGS..................................................... 12
6.4 SETTING THE TIME........................................................................... 13
6.5 SETTING THE TIME FORMAT ..........................................................14
6.6 SETTING THE DATE.......................................................................... 14

4
6.7 AUTO POWER OFF...........................................................................15
6.8 WIFI.......................................................................................................16
6.9 WIFI INFORMATION ......................................................................... 17
6.10 RESET WIFI......................................................................................... 18
6.11 ROTATE IMAGE.................................................................................19
6.12 DVR MODE ........................................................................................ 19
6.13 SCREEN SAVER..................................................................................20
6.14 LED INDICATOR ................................................................................21
6.15 KEYPAD TONE................................................................................... 22
7.0 PICTURE & VIDEO SETTINGS ........................................................ 24
7.1 VIDEO MODE ....................................................................................25
7.2 SLOW MODE..................................................................................... 27
7.3 LOOP MODE .....................................................................................29
7.4 LAPSE MODE.....................................................................................31
7.5 PHOTO MODE ..................................................................................33
7.6 AUTO MODE .....................................................................................35
7.7 BURST MODE ....................................................................................37
7.8 TIMER MODE..................................................................................... 39
7.9 PLAYBACK MODE ............................................................................. 41

5
8.0 RESTORE DEFAULT SETTINGS....................................................... 42
9.0 FIRMWARE VERSION ..................................................................... 43
10.0 INSTALLING AND USING THE ZX-ACTION APP .......................... 43
11.0 MANUAL STEPS FOR CONNECTING TO THE ZX-ACTION APP... 44
11.1 ZX-ACTION APP ................................................................................45
11.2 SAVING PHOTOS & VIDEOS VIA THE APP ....................................46
11.3 REMOTE PHOTO/RECORD VIA THE APP ......................................47
11.4 ADJUSTING SETTINGS VIA THE APP .............................................47
12.0 WARRANTY TERMS & CONDITIONS............................................. 48
13.0 NOTES ............................................................................................. 53

6
1.0 INTRODUCTION
Thank you for purchasing a Zero-X ZXM-AC3 action camera. Please read
through this User Manual before attempting to use the ZXM-AC3.
FEATURES
• 4K UHD Recording @ 30 FPS
• 2.0” Screen Touch Screen
• Waterproof Case
2.0 ABOUT THE ZXM-AC3
The Zero-X ZXM-AC3 shoots footage with dynamic realism, where action is
effortlessly captured into moments you can keep. There is a range of ZXM-
AC3 accessories available for purchase that will enhance your recording and
help you create fully immersive footage. To learn more about our extended
accessory range and for details on stockists, please visit the Zero-X website.
www.zero-x.com.au | www.zero-x.co.nz.

7
3.0 WHATS IN THE BOX
4.0 COMPONENTS
1 x ZXM-AC3 Action Camera
1 x USB Charging & Data Cable
1 x Waterproof Casing
1 x Bike Mount
2 x Quick Release Mounts
2 x 3M Adhesive Mounts
3 x 3 Way Mounts
1 x Frame Mount
4 x Straps
1 x Adaptor Mount
1 x Metal Tether
1 x Lens Cleaning Cloth
2 x 3M Adhesive Pads
1 x Tripod Adaptor
1 x Battery
1. Shoot/Record Button
2. LED Indicator Light
3. Micro USB Charging
Port
4. Micro SD Card Slot
5. Micro HDMI Out Port
6. Up/Down Button
7. Power ON/OFF
Button
8. Battery Port
1
8
6
3
5
2
7
4

8
5.0 GETTING STARTED
CAUTION:
Before using your action camera please ensure you read and understand the following
product and safety precautions.
• Do not use the ZXM-AC3 in water without the waterproof case.
• Do not use the ZXM-AC3 with the waterproof case in water deeper than 30m.
• Always check the waterproof case seal is clean and free of debris prior to use in water.
• Do not attempt to open the ZXM-AC3 or modify it in any way. If the ZXM-AC3 has
been tampered with the warranty will be void. Maintenance and repairs should only be
performed by Zero-X.
• If you have wet hands, do not handle or charge the ZXM-AC3 without it enclosed in the
waterproof case. Failure to do so may result in damage to the camera and/or injury.
• Only recharge the ZXM-AC3 battery using the supplied USB cable.
• Do not use the ZXM-AC3 in temperatures that exceed 55°C.
• Do not drop, crush, pierce, bend, deform, microwave, incinerate or shoot the ZXM-AC3.

9
BATTERY WARNING
Always charge the ZXM-AC3 using the provided USB Cable. If the ZXM-AC3 is not charged
as directed in this manual, the battery may become damaged and fail.
• Never dismantle the ZXM-AC3 or expose the internal battery cell.
• Do not dispose of the ZXM-AC3 in fire.
• Please dispose of the ZXM-AC3 mindfully and observe local regulations, especially in
regards to the safe disposal of the internal battery. Check your local recycling facility for
more information.
• Only use a certified 5V 1.5A USB charger to charge the ZXM-AC3. Using non certified
chargers could potentially damage the ZXM-AC3, or the ZXM-AC3 battery and void the
warranty.
• Do not let the battery charge overnight.
• If the ZXM-AC3 seems to still need charging after three hours, temporarily remove it from
its charger as the battery may overheat. Let it cool down for 30 minutes and try charging
again.
5.1 CHARGING THE BATTERY
We recommend that you fully charge your ZXM-AC3 before use. A full
charge will take approximately 3 hours using a 5V 1.5A charger.

10
5.2 MICRO SD CARD COMPATIBILITY
The ZXM-AC3 requires a Micro SD Card (not included) to save the
files. We recommend you use a maximum 128GB, UHS Class 3 or
higher Micro SD Card from a well known brand.
NOTE: There is only one correct way to insert the Micro SD Card into your ZXM-AC3. It
should easily slide in. Do not force the card into the slot as it may damage the unit
and the card.
5.3 TOUCH SCREEN COMPONENTS
5.4 POWERING ON YOUR ZXM-AC3
To power ON your ZXM-AC3 follow the below steps:
1. Insert the battery into the unit.
2. Press and hold the ON/OFF Button on the front of the unit until
the start up screen appears.
1
2 3 4
765
1. Current Mode
2.
Micro SD Card Inserted
3. Microphone ON
4. Battery Level
5. Playback
6. Mode Selection
7. Settings

11
5.5 FORMAT YOUR MICRO SD CARD
Before you start using the ZXM-AC3, we recommend that you format
the Micro SD card. You are able to format the Micro SD card using the
ZXM-AC3 via the following instructions:
1. If you are currently in video mode and recording, you will need to
press the SHOOT/RECORD Button to end the recording first.
2. Once the ZXM-AC3 is fully charged insert your Micro SD Card into
the correct slot (see the “4.0 COMPONENTS”).
3. Press the ON/OFF Button on the front of the unit to turn ON the
ZXM-AC3.
4. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to Press
the BUTTON again.
5. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
6. Scroll down the list by swiping from bottom to top until you reach
FORMAT SD CARD. PRESS on this option.
7. You will be prompted with the options FORMAT and CANCEL.
Press on the option that you require. Your Micro SD card will now
format.
NOTE:
Formatting the Micro SD card will permanently erase all data stored on
the Micro SD card. Be sure to back up all saved data prior to formatting.

12
6.0 ZXM-AC3 CONTROLS AND FUNCTIONS
6.1 POWER ON/OFF BUTTON
The ON/OFF Button is located at the front of the ZXM-AC3 in the
bottom left corner. This is used to turn ON/OFF the unit.
The ON/OFF Button is interchangable and is used to change between
video and photo modes, and between Video/Photo Settings - General
Settings - Exit.
6.2 SHOOT/RECORD BUTTON
The SHOOT/RECORD Button is located on right side on top of the
ZXM-AC3. This Button is used to shoot images and also record videos
(to start and stop videos).
The SHOOT/RECORD Button is also used to access the navigation
settings menus, select menu items, and confirm your selection.
6.3 ACCESSING SYSTEM SETTINGS
You can access system settings when using any of the camera modes.
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to
press the Button again.

13
6.4 SETTING THE TIME
To set the correct time on your ZXM-AC3, follow the below steps once
your unit is turned ON. You can set the date in separate settings.
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the BUTTON again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
TIME SETTING. Press on this option. The time settings screen will
pop up.
5. You will be prompted to fill in the current hour, minute and
seconds. Navigate by pressing either the hour, minute and second
on the screen. To change the numbers, press the UP and DOWN
arrows on the screen until you reach the required number.
6. Once you have adjusted the time, confirm by pressing the TICK on
the screen in the top right corner. The time will now be updated.
NOTE: The option which is bold and black is the active selection. Non active
options are grey. The time is 24 hour and is set as HH:MM:SS.

14
6.5 SETTING THE TIME FORMAT
To select a time format please follow these steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop-up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you
reach TIME FORMAT. Press on this option. The TIME FORMAT
SETTINGS screen will pop up.
5. Press on the option that you prefer. The TIME FORMAT will now
be updated.
6.6 SETTING THE DATE
To set the correct date on your ZXM-AC3, follow the below steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.

15
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
DATE SETTING. Press on this option. The DATE SETTING screen
will pop up.
5. You will be prompted to fill in the current year, month and day.
Navigate through by pressing on either year, month and day on
the screen. To change the numbers press the UP and DOWN
arrows on the screen until you reach the required number.
6. Once you have adjusted the date, confirm this by pressing the
tick on the screen in the top right corner. The time will now be
updated.
6.7 AUTO POWER OFF
The AUTO POWER OFF function is designed to help extend the
battery life of the ZXM-AC3. The ZXM-AC3 will automatically power
OFF after a selected period of inactivity (3, 5, 10 minutes and OFF).
The ZXM-AC3 is factory defaulted to 3 minutes. To change this setting,
follow the below steps:
1. If you are currently in VIDEO MODE and RECORDING, you will need
to press the SHOOT/RECORD Button to end the recording first.

16
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
AUTO POWER OFF. Press on this option. The AUTO POWER
OFF SETTINGS screen will pop up.
5. You can scroll through the options by swiping up and down on the
screen. Press on the option that you prefer. The setting will now
be updated.
6.8 WIFI
The ZXM-AC3 comes with inbuilt WiFi, allowing you to easily access
your footage and photos through your smartphone and use your
smartphone as an external wireless monitor to the camera. The
ZXM-AC3 default setting is OFF. For more information see “11.1 ZX-
ACTION APP.” To change this setting, follow the below steps:
1. If you are currently in VIDEO MODE and RECORDING, you will need
to press the SHOOT/RECORD Button to end the recording first.
2. Press the Button on the bottom right of the screen, this will open
up the SETTINGS MENU. A pop up with two locks and arrows may
appear. Swipe from left to right. You may need to press the
Button again.

17
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
WIFI. You will notice a box on the right of screen with TURN OFF
next to it. Press on this box. The WIFI is now active.
5. To exit out of WIFI MODE,Press the UP BUTTON.
NOTE: When WiFi is connected to your smartphone, you cannot use the
functions on the ZXM-AC3 via the camera however you can manage
functions via the app in this mode. You can also use your smartphone as a
wireless recording monitor when in WiFi mode. You can control functions
via the ZXM-AC3 camera again once you have finished using the
functions of the ZX-ACTION APP and disconnect from your smartphone.
6.9 WIFI INFORMATION
If you need to find out the connection name and password of the ZXM-
AC3 WiFi ID, you can find this in the WiFi information section. To access
this, follow the below steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.

18
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
WIFI INFORMATION. Press on this option to see the WiFi ID
information.
5. WiFi information will have WIFI ID and WIFI PASSWORD. The
WiFi Name will be ZXM-AC3_XXXX ( XXXX will be unique to every
action camera) Password: 1234567890
6.10 RE-SET WIFI
If you need to re-set the ZXM-AC3 WiFi connection, follow the steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
RESET WIFI. Press on this option.
5. You will be prompted to CONFIRM or CANCEL. PRESS on the
option you require. If you press confirm, the WIFI will be reset.

19
6.11 ROTATE IMAGE
You have the ability to flip the image vertically (upside down) when
you are using the ZXM-AC3, by turning on this function. The ZXM-AC3
default setting is OFF. To change this setting, follow the steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Image Rotation is the first option on the settings menu. You will
notice there is a small box with TURN OFF next to it. Press the
box to activate this function. It will now say TURN ON. The camera
image will now be flipped vertically (upside down).
6.12 DVR MODE
When DVR mode is activated, the ZXM-AC3 will continue to record until
the unit has run out of power. It will start recording again as soon as the
action camera is connected to power. The ZXM-AC3 default setting is
OFF. To change this setting, follow the below steps:

20
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.
2. Press the Button on the bottom right of the screen, this will
open up the SETTINGS MENU. A pop up with two locks and
arrows may appear. Swipe from left to right. You may need to press
the Button again.
3. Press the tab on the left side of the screen. The current section
tab will be highlighted blue.
4. Scroll down the list by swiping from bottom to top until you reach
DVR MODE. You will notice there is a small box with TURN OFF
next to it. Press the box to activate this function. It will now say
TURN ON.
6.13 SCREEN SAVER
You can record videos and conserve power with the screen saver
function, allowing the LCD display to turn OFF while the ZXM-AC3
continues to record. There are four options to choose from for
the screen saver function activating: 30 SECONDS, 1 MINUTE,
2 MINUTES and OFF. The ZXM-AC3 default setting is set to 30
SECONDS. To change the this setting, follow the below steps:
1. If you are currently in VIDEO MODE and RECORDING, you will
need to press the SHOOT/RECORD Button to end the recording
first.