Rev :X01.
Zhejiang Lianda Science Technology Co Ltd& .,
2 .Check Change if needed the Motor rotation direction) / ( )
-
.
-
down.
(
)
( .).
Check the direction of rotation with the
remote control that have been recorded
Confirm that the UP button brings the
application up or
see OK
schema please wait until the jog
8sec
If the direction is correct
If the direction is not correct(
)
-
. , .
.
- .
see
NO schema
Press the STOP button for more than
2 sec until the motor jogs then release
The rotation direction will change
Check the direction
Remark You have 8sec to change the
rotation direction after recording the
first Remote Control
: .
.
* , .
" => " .
* , .=> " ' " .
If the direction is still wrong after the jog you must do a motor reset to change the direction again Please refer to step 6
Resetting the Motor Back to factory mode section
In case of Remote Control is damaged lost or unable to work Refer to step 5 Resetting the motor s memory section
- .
-
.
-
.
- .
.
Press the DOWN button of the Remote Control
Stop the motor where you want to set the down
limit
Adjust if necessary by pressing the UP or DOWN
buttons
Press the STOP button for 2 sec Until the motor
jogs
A Setting the down limit.
3 .Setting the Limits only for Radio motor with radio
limit setting
) (
)
-
( ° )
.
-
°
Press the PROG Button with a thin head
thing on the already recorded Remote
Control N 1 for 2 sec. until the motor
jogs
Select the new Remote Control or channel
to add(N 2)and press its PROG Button for
0.5sec.until it jogs,then release.
Add a Remote Control or Channel
-
( ° )
.
-
( ) °
Press the PROG Button on an already
recorded one N 1 for 2 sec. until the
motor jogs
Select the Remote Control or channel
need to be deleted to delete(N 2)
and press its PROG button for 0.5sec.
until it jogs,then release.
Delete a Remote Control or Channel
5 .Resetting the Motor s memory when a Remote Control is lost) '
- .
- .
- + +
.
-
.
.
,
.
Switch the power off 5sec
Switch the power on
Press simultaneously on UP STOP DOWN buttons
for 0.5 sec.until the motor jogs
Press simultaneously on PROG button of the new Radio remote control for
0.5 sec.until the motor jogs
After that you can use your motor normally
For Radio motor with radio setting
from Limit switch memory and replace by new one
of the new Radio remote
control
only remote controls had been removed
4 .Add Delete a Remote Control Channel) / /
6 .Resetting the Motor s Back to factory mode) ' =>
- .
-
.
-
.
- .
.
Press the UP button of the
Stop the motor where you want o set the up
limit
Adjust if necessary by pressing the UP or DOWN
buttons
Press the STOP button for 2 sec ntil the motor
jogs
Remote Control
t
u
B Setting the up limit.
- .
- .
- + +
.
- ( ,
( .))
- .( )
,
( ).
Switch the power off 5sec
Switch the power on
Press simultaneously on UP STOP DOWN buttons
RTL remote control for 0.5sec.until the motor jogs
Press 7s on PROG button of the RTL remote control after 2s the motor jogs
you should continue to press until 2 jog 7sec
Switch the power off 5sec
After that you will go back to factory mode(
) so you need to record a Radio remote control inside memory
refer to step1
of the already recorded
all remote controls have been
removed for radio motor with radio limit setting the end limits has been
removed too
, ,
.
nd
only for radio motor with manual limit setting
6.How to identify Radio motor with Manual limit setting and Radio motor with radio limit setting
If the radio motor shows an abnormal behaviour during the setup phase or during the factory mode reset,it may be that you are not referring to the
correct radio motor instruction:
For Radio motor with Manual limit setting
- ( ) .
-
.
-
.
(
)
( .).
Power up AC one motor at a time
Check the direction of rotation with
the remote control that have been
recorded
Confirm that the UP button brings
the application up or in
see OK
schema please wait until the jog
sec
If the direction is correct
12
If the direction is not correct(
)
-
. , .
.
- .
see
NO schema
Press the STOP button for more than
2 sec until the motor jogs then release
The rotation direction will change
Check the direction
For Radio motor with radio limit setting
Please ensure that you are using the correct radio motor instruction.
For Installer: check the radio motor head. If the radio motor head has a manual limit switch worm, it is a radio motor with manual limit setting. If not,
it is a motor with radio limit setting.
.
For User: the behaviour will only differ at the first remote setting or after a factory reset. If the radio motor loses the limit setting,it is a radio motor
with radio limit setting (for this type of radio motor, after a factory reset, the limit must be set up again, as well as the rotating direction The Keyring
can not be used to do these two operations). Otherwise it is a radio motor with manual limit setting. (Only direction must be checked).
5)
6)
5 sec.
12 sec.
2 sec.
2 sec.2 sec.
* ,
.
* =>
"" =>
" .
If you had recoreded a wrong down limit
power off the motor in order to resetthe
setting
If you had recorded a wrong up limit
Refer to step 6 Resetting the motor
Back to factory mode section
Warning Performing this procedure could erase all Remote Controls from the motor s memory But for radio motor with radio
limit setting the set limit switch point will however be saved
:
, .
' .
8 sec.
Add Economic Development Zone2 Nanxun HuZhou Zhejiang Province China: , , , , Customer service number: 86 572 3787117+ - -
P C 313009 Fax 86 572 3911465 E MAIL info lianda lianda com Website http www lianda com. : : - - - : - @ . : :/ / . .
N1
N2
Prog
0 5sec
.
. .
