ZIGBEE VN22776 User manual

1
ZIGBEE DÆMPER · RGBW
4CH x 5A (24VDC)
VN22776 ∙ MANUAL / DEVELTRON VN22776 ∙ MANUAL / DEVELTRON
1-
LED
2-
3-
4-
ZigBee Single Color Rece iv er
Prog.
V+ V+
V- V-
ZigBee LED Dimming Light Device 09.ZG1FD.04280
1-
LED OUT PUT
2-
3-
4-
Function introduction
Important: Read All Instructions Prior to Installation
12-36VDC Input
Common Anode output(+)
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Product Data
Safety & Warnings
Input Voltage Output Type
Output Current
12-36VDC Constant voltage240-720W
4CH, 5A/CH
Output Power
12-36VDC Constant current
16.8-50.4W
4CH, 0.35A/CH
12-36VDC Constant current
33.6-100.8W
4CH, 0.7A/CH
No.
1
2
3
Dimension (LxWxH)
170x53.4x28mm
170x53.4x28mm
170x53.4x28mm
CH 1 output(-)
CH 2 output(-)
CH 3 output(-)
CH 4 output(-)
ZigBee Single Color Receiver
• ZigBee LED dimming light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF and light intensity of connected LED lights
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator
• Enables to add devices to the self-formed zigbee network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal ZigBee gateway products
• Compatible with universal single color ZigBee remotes
• Waterproof grade: IP20
Prog.
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
Program Key: short press to switch on/off the device,
press and hold down to increase/decrease light intensity
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
4. TouchLink to a Zigbee Remote
< 10cm
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how.
Step 4: Connected light will blink 5 times and
then stay solid on, then the device will appear
in your controller's menu and can be
controlled through controller or hub interface.
Step 4: There shall be
indication on the remote for
successful link and connected
light will flash twice.
1-
LED
2-
3-
4-
ZigBee Single Color Rece iv er
Prog.
V+ V+
V- V-
Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink
commissioning immediately, 180S timeout, repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,
repeat the operation.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
seconds timeout, repeat the operation.
ZigBee RGBW LED Light Device 09.ZG3FW.04282
1/R-
LED OUTPUT
2/G-
3/B-
4/W-
Function introduction
Important: Read All Instructions Prior to Installation
12-36VDC Input
Common Anode output (+)
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Product Data
Safety & Warnings
Input Voltage Output Type
Output Current
12-36VDC Constant voltage240-720W
4CH, 5A/CH
Output Power
12-36VDC Constant current
16.8-50.4W
4CH, 0.35A/CH
12-36VDC Constant current
33.6-100.8W
4CH, 0.7A/CH
No.
1
2
3
Dimension (LxWxH)
170x53.4x28mm
170x53.4x28mm
170x53.4x28mm
CH 1 (R) output (-)
CH 2 (G) output (-)
CH 3 (B) output (-)
CH 4 (W) output (-)
ZigBee RGBW Receiver
Note: W channel can only be controlled through color temperature control command since Zigbee only has
tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color
tuning with the 4th channel white.
• ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights
• W channel can only be controlled through color temperature control command
• Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the
4th channel white
• ZigBee end device that supports Touchlink commissioning
• Supports find and bind mode to bind a ZigBee remote
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20
• Supports self-forming zigbee network without coordinator
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity
Prog.
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
4. TouchLink to a Zigbee Remote
< 10cm
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
V+ V+
R- R-
G- G-
B- B-
W- W-
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
seconds timeout, repeat the operation.
Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink
commissioning immediately, 180S timeout, repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,
repeat the operation.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how.
Step 4: Connected light will blink 5 times
and then stay solid on, then the device
will appear in your controller's menu and
can be controlled through controller or
hub interface.
Step 4: There shall be
indication on the
remote for successful
link and connected
light will flash twice.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset the
lighting device as instructed. The connected light blinks 3 times to indicate
successful reset.
1-
LED
2-
3-
4-
ZigBee Single Color Receiver
Prog.
V+ V+
V- V-
ZigBee LED Dimming Light Device 09.ZG1FD.04280
1-
LED OUT PUT
2-
3-
4-
Function introduction
Important: Read All Instructions Prior to Installation
12-36VDC Input
Common Anode output(+)
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Product Data
Safety & Warnings
Input Voltage Output Type
Output Current
12-36VDC Constant voltage240-720W
4CH, 5A/CH
Output Power
12-36VDC Constant current
16.8-50.4W
4CH, 0.35A/CH
12-36VDC Constant current
33.6-100.8W
4CH, 0.7A/CH
No.
1
2
3
Dimension (LxWxH)
170x53.4x28mm
170x53.4x28mm
170x53.4x28mm
CH 1 output(-)
CH 2 output(-)
CH 3 output(-)
CH 4 output(-)
ZigBee Single Color Receiver
• ZigBee LED dimming light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF and light intensity of connected LED lights
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator
• Enables to add devices to the self-formed zigbee network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal ZigBee gateway products
• Compatible with universal single color ZigBee remotes
• Waterproof grade: IP20
Prog.
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
Program Key: short press to switch on/off the device,
press and hold down to increase/decrease light intensity
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
4. TouchLink to a Zigbee Remote
< 10cm
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Zigbee
Remote
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how.
Step 4: Connected light will blink 5 times and
then stay solid on, then the device will appear
in your controller's menu and can be
controlled through controller or hub interface.
Step 4: There shall be
indication on the remote for
successful link and connected
light will flash twice.
1-
LED
2-
3-
4-
ZigBee Single Color Receiver
Prog.
V+ V+
V- V-
Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink
commissioning immediately, 180S timeout, repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,
repeat the operation.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
seconds timeout, repeat the operation.
ZigBee RGBW LED Light Device 09.ZG3FW.04282
1/R-
LED OUT PUT
2/G-
3/B-
4/W-
Function introduction
Important: Read All Instructions Prior to Installation
12-36VDC Input
Common Anode output (+)
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Product Data
Safety & Warnings
Input Voltage Output Type
Output Current
12-36VDC Constant voltage240-720W
4CH, 5A/CH
Output Power
12-36VDC Constant current
16.8-50.4W
4CH, 0.35A/CH
12-36VDC Constant current
33.6-100.8W
4CH, 0.7A/CH
No.
1
2
3
Dimension (LxWxH)
170x53.4x28mm
170x53.4x28mm
170x53.4x28mm
CH 1 (R) output (-)
CH 2 (G) output (-)
CH 3 (B) output (-)
CH 4 (W) output (-)
ZigBee RGBW Receiver
Note: W channel can only be controlled through color temperature control command since Zigbee only has
tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color
tuning with the 4th channel white.
• ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights
• W channel can only be controlled through color temperature control command
• Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the
4th channel white
• ZigBee end device that supports Touchlink commissioning
• Supports find and bind mode to bind a ZigBee remote
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20
• Supports self-forming zigbee network without coordinator
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity
Prog.
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
4. TouchLink to a Zigbee Remote
< 10cm
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
V+ V+
R- R-
G- G-
B- B-
W- W-
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Dev ic e
Prog.
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Dev ic e
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
seconds timeout, repeat the operation.
Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink
commissioning immediately, 180S timeout, repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,
repeat the operation.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how.
Step 4: Connected light will blink 5 times
and then stay solid on, then the device
will appear in your controller's menu and
can be controlled through controller or
hub interface.
Step 4: There shall be
indication on the
remote for successful
link and connected
light will flash twice.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset the
lighting device as instructed. The connected light blinks 3 times to indicate
successful reset.
• ZigBee RGBW LED-lysenhed baseret på den nyeste ZigBee 3.0-protokol.
• Gør det muligt at kontrollere ON / OFF, lysintensitet og RGB-farve på tilsluttede RGBW LED-lys
• W-kanalen kan kun styres ved hjælp af kommandoen for farvetemperaturstyring
• Farvetemperaturregulering blander RGB-kanaler som 1 kanals hvid og foretager derefter
farvetuning med 4. kanal hvid
• Kompatibel med universelle ZigBee gateway-produkter
• Vandtæt kvalitet: IP20
SIKKERHED OG ADVARSLER
• Installer IKKE med strøm tilsluttet enheden.
• Udsæt IKKE enheden for fugt.
PRODUKTDATA
INTRODUKTION
Prog. taste: Kort tryk: On/ Off.
Tryk og hold nede: Dæmper eller øger lysstyrken.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset
the lighting device as instructed. The connected light blinks 3 times to
indicate successful reset.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Prog.
V+ V+
V- V-
6. Factory Reset Manually
Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 2: Connected light will blink 3 times
to indicate successful reset.
Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if
the “Prog.” key is not accessible.
< 10cm
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 4: There shall be indication
on the remote and connected
light flashes 3 times for
successful reset.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Note: Make sure the device already added to a network, the remote added to the same one or not added to any
network.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touch Reset procedure to reset the
device, please refer to corresponding remote or touch panel manual to learn how.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Prog.
V+ V+
V- V-
Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Pro g.
V+ V+
V- V-
8. Find and Bind Mode
Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it
to find and bind initiator, please refer to corresponding remote or touch panel manual.
Step 3: There shall be indication on the remote or touch panel that it bind the device
successfully and can control it then.
Zigbee
Remote
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind
mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Prog.
V+ V+
V- V-
9. Learning to a Zigbee Green Power Remote
Step 2: Set the green power
remote into Learning mode,
please refer to its manual.
Zigbee
Green Power
Remote
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 3: Connected light will
flash twice to indicate
successful learning. Then the
remote can control the device.
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode
(connected light flashes twice), 180 seconds timeout, repeat the operation.
Note: Each device can learn to
max. 20 zigbee green power remote.
10. Delete Learning to a Zigbee Green Power Remote
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Pro g.
V+ V+
V- V-
Step 2: Set the paired green power remote into
Learning mode, please refer to its manual.
Zigbee
Green Power
Remote
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Step 3: Connected light will
flash 4 times to indicate
successful deleting.
Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times) to start delete Learning mode
(connected light flashes slowly), 180 seconds timeout, repeat the operation.
FUNKTION
1. Tilslut ledningerne korrekt iht. tilslutningsdiagrammet.
2. Denne ZigBee-enhed er en trådløs modtager, der kommunikerer med en række ZigBee-kompatible
systemer. Denne dæmper modtager og styres af trådløse radiosignaler fra kompatible ZigBee
systemer.
ZIGBEE-NETVÆRK / PARRING
Gennem koordinator eller hub (Tilføjet til et Zigbee-netværk)
Trin 1: Fjern enheden fra forrige zigbee-netværk, hvis den allerede er føjet til, ellers vil parring svigte.
Der henvises til delen ”Fabriksindstilling - manuelt”.
Trin 2: Fra din ZigBee Controller eller hub-interface skal du vælge at tilføje belysningsenhed og gå ind i
Parringstilstand som instrueret af controller.
Trin 3: Tænd for enheden igen for at sætte den i netværksparretilstand (tilsluttet lys blinker langsomt to
gange), 15 sekunder timeout, gentag handlingen.
Trin 4: Tilsluttet lys blinker 5 gange og forbliver
derefter tændt, så vises enheden i din controllers
menu og kan være styres via controller eller hub
interface.
ZIGBEE-NETVÆRK / FJERNELSE AF DÆMPER FRA NETVÆRK vha. HUB Interface
Vælg at slette eller nulstille fra din ZigBee-controller eller
hub-interface belysningsanordningen som beskrevet.
Det tilsluttede lys blinker 3 gange til indikere vellykket
nulstilling.
12-24VDC indgangsspænding
12-24VDC
Fælles (+)
12-24VDC 240-480W
Dimensioner (LxBxH)Dæmper type
Udgangseffekt
Spænding (PWM)
Udgangsstrøm
Indgangsspænding
Bemærk: W-kanalen kan kun styres ved hjælp af kommandoen for farvetemperaturstyring, da Zigbee kun har
indstillelig hvid kontrol. Farvetemperaturregulering vil blande RGB-kanaler som 1 kanals hvid og derefter
blande dem med den 4. kanal hvid.

2
Input Clusters
• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes
• 0x0006: On/off • 0x0008: Level Control • 0x0300: Color Control • 0x0b05: Diagnostics
Output Clusters
• 0x0019: OTA
12. ZigBee Clusters the device supports are as follows:
13. OTA
Wiring Diagram
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
Connect w ith RGBW LE D Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
Connect w ith RGBW LE D Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
1/R-
LED
2/G-
3/B-
4/W -
ZigBee RGBW Receiver
1/R-
LED
2/G-
ZigBee RGBW Receiver
Prog.
3/B-
4/W -
Prog.
The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.
Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the
remotes, refer to their manuals.
Note: 1) Each added device can link and be controlled by max. 30 added remotes.
2) Each added remote can link and control max. 30 added devices.
VN22776 ∙ MANUAL / DEVELTRON VN22776 ∙ MANUAL / DEVELTRON
6. Factory Reset Manually
Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
V+ V+
R- R-
G- G-
B- B-
W- W-
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if
the “Prog.” key is not accessible.
8. Find and Bind Mode
Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and
Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.
Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it
to find and bind initiator, please refer to corresponding remote or touch panel manual.
Step 3: There shall be indication on the remote or touch panel that it bind the device
successfully and can control it then.
< 10cm
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 4: There shall be
indication on the remote and
connected light flashes 3
times for successful reset.
Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Note: Make sure the device already added to a network, the remote added to the same one or not added to any
network.
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touch Reset procedure to reset the
device, please refer to corresponding remote or touch panel manual to learn how.
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 2: Connected light will blink 3 times
to indicate successful reset.
9. Learning to a Zigbee Green Power Remote
Step 2: Set the green power
remote into Learning mode,
please refer to its manual.
Zigbee
Green Power
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 3: Connected light
will flash twice to indicate
successful learning. Then
the remote can control the
device.
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode (connected
light flashes twice), 180 seconds timeout, repeat the operation.
Note: Each device can learn to
max. 20 zigbee green power remote.
10. Delete Learning to a Zigbee Green Power Remote
Step 2: Set the paired green power remote into
Learning mode, please refer to its manual.
Zigbee
Green Power
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 3: Connected light will
flash 4 times to indicate
successful deleting.
Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times) to start delete Learning mode
(connected light flashes slowly), 180 seconds timeout, repeat the operation.
11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
V+ V+
R- R-
G- G-
B- B-
W- W-
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
1/R-
LED
2/G-
3/B-
4/W-
ZigBee RGBW Lighting Device
Prog.
< 10cm TouchLink
Step 2: Set another device or remote or touch panel into
network pairing mode and pair to the network, refer to their
manuals.
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a
zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat
the operation.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Prog.
1-
LED
2-
3-
4-
ZigBee Single Color Recei ve r
Pro g.
V+ V+
V- V-
11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
Zigbee
Remote
L
N
GV+
V-
OUTPU T
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
< 10cm TouchLink
Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to
their manuals.
Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the
remotes, refer to their manuals.
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a
zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat
the operation.
Note: 1) Each added device can link and be controlled by max. 30 added remotes.
2) Each added remote can link and control max. 30 added devices.
12. ZigBee Clusters the device supports are as follows:
Input Clusters
• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0006: On/off
• 0x0008: Level Control • 0x0b05: Diagnostics
Output Clusters
• 0x0019: OTA
13. OTA
The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.
Product Dimension
170 mm
53.4 mm 28 mm
L
N
GV+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
V+ V+
1- V-
2- V-
3- V-
4- V-
Conne ct wi th Si ngle Color L ED St rip
V+ V+
1- V-
2- V-
3- V-
4- V-
Conne ct wi th Si ngle Color L ED St rip
1-
LED
2-
3-
4-
ZigBee Si ngle Color Re ceiver
1-
LED
2-
3-
4-
ZigBee Si ngle Color Re ceiver
Prog.
Prog.
Wiring Diagram
Trin 1: Tryk kort på “Prog.”- tasten i 5 gange eller tænd og sluk enheden 5
gange, hvis “Prog.”- tasten ikke er tilgængelig.
FABRIKSINDSTILLING / MANUELT
Trin 2: Det tilsluttede lys blinker 3 gange
for at indikere en vellykket nulstilling.
BEMÆRK: 1) Hvis enheden allerede er tilbage i fabriksindstillingen, er der ingen indikation.
 2)Allekongurationsparametrenulstilles,nårenhedenblivernulstilletellerfjernetfranetværket.
OTA
EnhedenunderstøtterrmwareopdateringgennemOTAogfårnyrmwarefrazigbeecontroller
eller hub automatisk hvert 10. minut.
PRODUKT DIMENSIONER
KOBLINGSDIAGRAM
RGBW LED bånd
RGBW LED bånd