Zinc ZN25151 User manual

Dion 180 Degree
PIR Sensor
ZN25151
User Instructions
Welcome to use ST10A Infrared motion sensor!
The product adopts good sensitivity detector and integrated circuit. It gathers automatism,
convenience, safety, saving-energy and practical functions. It utilizes the infrared energy from
human as control-signal source and it can start the load at once when one enters detection field.
It can identify day and night automatically. It is easy to install and used widely.
SPECIFICATION:
Power Source: 220-240V/AC Detection Range: 180
Power Frequency: 50Hz Detection Distance: 5-12m (<24 ) adjustable
Ambient Light: <3-2000LUX (adjustable) Working Temperature: -20~+40
Time Delay: Min.10sec 3sec Working Humidity: <93%RH
Max.7min 2min Power Consumption: approx 0.5W
Rated Load: Max.1200W Installation Height: 1.8-2.5m
300W Detection Moving Speed: 0.6-1.5m/s
FUNCTION :
Can identify day and night: The consumer can adjust working state in different ambient light.
It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can
work in the ambient light less than 3LUX when it is adjusted on the “moon” position (min). As
for the adjustment pattern, please refer to the testing pattern.
SENS adjustable: It can be adjusted according to using location. The detection distance of
low sensitivity could be only 5m and high sensitivity could be 12m which fits for large room.
Time-Delay is added continually: When it receives the second induction signals within the
first induction, it will restart to time from the moment.
Good sensitivity Poor sensitivity
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following situations:
Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors
etc.
Avoid mounting the detector near heat sources, such as heating vents, air conditioning
units, light etc.
Avoid pointing the detector towards objects that may move in the wind, such as curtains,
tall plants etc.
LED Compatible

CONNECTION:
Warning. Danger of death through electric shock!
Must be installed by professional electrician.
Disconnect power source.
Cover or shied any adjacent live components.
Ensure device cannot be switched on.
Check power supply is disconnected.
Screw off the nail on the front cover and unload the front cover. (refer to figure1).
Find the wire hole with gasket in the bottom and pass the power wire through hole.
Fix the bottom on the selected position with the inflated screw (refer to figure 2).
Connect the power wire into connection-wire column according to the connection-wire
diagram.
Install back the front cover, tighten the screw and switch on the power. Then you can test it.
Figure1 Figure2
CONNECTION-WIRE DIAGRAM:
(See the right figure)
TEST :
Turn the SENS knob clockwise on the maximum(+).Turn the
TIME knob anti-clockwise on the minimum(-).Turn the LUX knob
clockwise on the maximum (sun).
Switch on the power; the sensor and its connected lamp will have
no signal at the beginning. After Warm-up 30sec, the sensor can
start work .If the sensor receives the induction signal, the lamp
will turn on. While there is no another induction signal any more,
the load should stop working within 10sec 3sec and the lamp would turn off.
Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than
3LUX, the sensor would not work and the lamp stop working too. If you cover the detection
window with the opaque objects (towel etc), the sensor would work .Under no induction
signal condition, the sensor should stop working within 10sec 3sec.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise
the sensor lamp could not work! If the lamp is more than 60W, the distance between
lamp and sensor should be 60cm at least.
SOME PROBLEM AND SOLVED WAY :
The load do not work:
a. Please check if the connection-wiring of power and load is correct.
b. Please check if the load is good.
c. Please check if the working light sets correspond to ambient light.
The sensitivity is poor:
a. Please check if there has any hindrance in front of the detection window to affect to
receive the signal.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection fields.
d. Please check if the installation height corresponds to the height showed in the
instruction.
e. Please check if the moving orientation is correct.
The sensor can not shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is the longest.
c. Please check if the power corresponds to the instruction.
Helpline
If you receive this item with parts broken or missing, please telephone:
0333-005-0077
Please have ready your name, address, tel. no., product reference, where purchased
and parts required. An answering service is in operation outside office hours and during busy
periods.
We regret that we are unable to give advice on internal house wiring.
Cascade Holdings Ltd, Gorse Mill, Gorse Street, Chadderton, Oldham. OL9 9RJ