Zip HydroTap G4 User manual

801314 v3.05 09.20 HT BC Commercial Instructions Page 1 of 28
Zip HydroTap G4
Affix Model Number Label
Here
801314
Installation and Operating Instructions
®
BC Commercial

Page 2 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Tap Options
The Zip HydroTap G4 appliance series offers a range of interchangeable taps to suit the customer’s needs
These taps are directly compatible with the HydroTap G4
Command Centre.
The All-In-One Tap is a stand alone tap that may be used
as an alternative to any of the above combinations.
The Mixer tap range is an additional series of taps that
may be used in conjunction with any one of the taps
shown above, to create 4-in-1 models
Arc / Cube Tap
Arc / Cube Mixer
Classic Tap
Elite Tap
Classic All-In-One Celsius All-In-One

801314 v3.05 09.20 HT BC Commercial Instructions Page 3 of 28
HydroTap Specifications
Installation Checklist .................................................................................................................... 4
General Product Features............................................................................................................ 5
Important Safety Instructions ....................................................................................................... 6
Warnings and Regulatory Information.......................................................................................... 7
Major Components and Accessories ........................................................................................... 8
Technical Specification ................................................................................................................ 9
Before Installation and Site Requirements................................................................................... 10
Installation Instructions
STEP 1 - Fit the tap to the benchtop or sink before installing the Command Centre.
(Refer to the Tap installation instruction book 803341)
STEP 2 - Check for adequate ventilation
Section 2- Ventilation
2.1- Ventilation for All Models ............................................................................................11
STEP 3 - Install the Booster Heater (if required)
Section 3 - Booster Heater Installation
3.1- Product Description.................................................................................................... 13
3.2- Installation Procedure ................................................................................................ 14
3.3- To Remove / Install the appliance ............................................................................. 14
3.4- Braided Hose Connections ........................................................................................ 15
STEP 4 - Mount the external filter / softener (if required)
Section 4 - Command Centre Installation
4.1- External Bypass Valve .............................................................................................. 16
4.2- Hose and tube fitting.................................................................................................. 16
STEP 5 - Install the Command Centre
Section 5 - Command Centre installation
5.1- Check the external bypass valve setting ................................................................... 17
5.2- Fit the mains water supply hose ................................................................................ 17
5.3- Model BC 160/125 and BC 160/175 .......................................................................... 18
5.4- Model BC 240/175 ..................................................................................................... 19
5.5- Model AIO Mains ....................................................................................................... 20
5.6- Model AIO Vented...................................................................................................... 21
5.7- Model 4-In-1 Vented .................................................................................................. 22
STEP 6 - Commission the HydroTap
Section 6 - Commissioning
6.1- Select the Language.................................................................................................. 23
6.2- Filter Flush ............................................................................................................... 23
6.3- Boiling Calibration...................................................................................................... 24
6.4- Booster....................................................................................................................... 24
6.5- Safety Sensor Calibration .......................................................................................... 25
6.6- Command-Centre Flush............................................................................................. 25
Troubleshooting Table ................................................................................................................. 26
End of Life Disposal ..................................................................................................................... 27
Contact Details............................................................................................................................. 28
Index

Page 4 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Before Installation:
A. Read the instructions and check if there is adequate space to mount all of the components.
B. Note: Not all fittings are supplied with the appliance kit. Isolation valves are not supplied.
C. Check the mains water pressure is between 150 - 700kPa and 200 - 700kPa when a booster
and /or filter softener is fitted
D. Check the water quality to determine if extra filtration will be required.
NOTE: This product must be fitted to a potable water supply
E. Check the appliance rating plate and ensure correct power is available for the appliance.
F. Check the under counter cupboard supporting the appliance is adequate for
the total weight of the appliance, when full of water.
Before Commissioning:
1. Check the Command Centre has been installed correctly.
2. Check all plumbing fittings have been tightened.
3. Ensure the outlet and vent pipes are positioned to drain correctly.
4. Ensure there is adequate ventilation.
5. Check all tubes from the tap to the Command Centre have constant fall and there are no
sags or kinks in the hoses.
6. Check all electrical connections are correct and there are no loose wires.
Commission: (see section 6)
7. Flush the supply line before connecting.
8. Turn on the water and check for leaks.
9. Flush the filter(s).
10. Where applicable, program the Command Centre to suit the customer’s requirements.
Installation Checklist

801314 v3.05 09.20 HT BC Commercial Instructions Page 5 of 28
Thank you for purchasing a Zip HydroTap. Please read and follow these instructions carefully to ensure safe
and trouble free service. For enquiries and service, please contact your Zip service provider.
What is the Zip HydroTap ?
The Zip HydroTaps are electronically controlled, filtered, boiling water and chilled water drinking systems for
kitchens and tea rooms. The HydroTap Command Centre is an under-bench drinking water appliance with a
dispensing tap mounted on a sink or bench, which may be used for residential or commercial applications.
These units utilise a conventional refrigerant compressor to chill the water and an immersion heating element
to boil the water. These units dispense boiling water (factory set to 98°C) and chilled water (factory set to
5-9°C). These units are NOT designed to be used for sanitary fixtures.
The Boiling water Command Centres are fitted with a tap mounted, safety lock. In addition, there are
various energy saving options accessible via the main menu. Each Command Centre is equipped with a
self-calibrating program which caters for altitude adjustment. The water filter is a disposable item which will
require periodic replacement and is covered by a limited OEM warranty.
It is important that the Installation be done safely, correctly and completely, in order to utilise all the benefits
the HydroTap can provide. Classic and All-In-One taps may be ordered with the Tap Head Assembly for
Disabled use. The disabled levers are supplied with Braille caps for the visually impaired.
General Product Features
HydroTap Classic
BC160/125

Page 6 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Important Safety Instructions
This manual contains important safety and installation instructions for the Zip HydroTap.
Safety
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
For products sold in Europe, this appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Refrigerant
The HydroTap Command Centre contains R134A refrigerant under pressure. Maintenance of the refrigeration
unit must be carried out by an accredited service provider or qualified refrigeration technician.
Qualifications
If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all
Installation procedures must be carried out by a suitably qualified tradesperson. The power cable and power
outlet must be in a safe visible position for connection.
Venting
Sometimes steam and / or condensed droplets may discharge through a vent outlet at the tap. If the tap is not
installed using the Font pedestal, ensure the tap body is located so the tap outlet safely dispenses into the
sink bowl area.
Lifting
Take care when lifting the Zip HydroTap Command Centre. Some units may exceed safe lifting limits. If you
feel this is beyond your personal capabilities, please seek assistance with the lift. The weights of the units are
marked on the packaging. Do not lift the Command Centre by the front cover or any connections at the top
rear of the Command Centre. Refer to the technical specification for the weight of your product.
Airflow
The HydroTap Command Centre must operate within ambient operating temperatures between 5ºC - 35ºC,
when installed in a cupboard. The system will operate satisfactorily only with proper air ventilation and with
recommended air gaps of 50mm on each side. See section 2 for correct Installation details.
Frost Protection
If this appliance is located where the ambient air temperature could fall below 5ºC when the Command
Centre is not in use, do not turn off the appliance electrically. This safeguard does not offer the same
protection to the connecting pipework and fittings
Positioning
It is important to ensure the Command Centre is positioned in an accessible area close to the floor level. The
Command Centre must have its base mounted in a horizontal position with all inlets and outlets facing up.
The Tap must be located above the Command Centre and positioned so that it dispenses into the sink bowl
with ample clearance for a cup or tea pot. See section 1 for details.
!

801314 v3.05 09.20 HT BC Commercial Instructions Page 7 of 28
Important Safety Instructions
WARNINGS
1. The HydroTap Command Centre must be earthed. The resistance of the
earth connection from each exposed metal part must be less than 1 ohm.
2. All Installation and service work must be completed by trained and
suitably qualified Tradespeople. Faulty operation due to unqualified
persons working on this product, or any other Zip product may void
warranty coverage.
3. Plumbing and electrical connections must be made in accordance with
local regulations and relevant standards. In Australia and New Zealand:
Plumbing standard AS/NZS 3500 & Electrical Wiring Rules AS/NZS 3000.
4. This HydroTap product is rated for 230V 50Hz AC operation.
5. This Command Centre must be installed with adequate clearances
of 50mm on all sides, and 200mm above, to allow for air circulation.
Additional means of ventilation is critical if the vent kit, as supplied, cannot
be fitted.
6. Flush water supply lines before any plumbing connections are made, to
prevent sediment from affecting operation.
7. The Command Centre must not be located near, or cleaned with water
jets.
8. This product is designed for indoor use and must not be installed outdoors
or exposed to the elements of nature.
9. For safe operation, the HydroTap is designed to be installed,
commissioned and used within 48 hours. Should the HydroTap not be
required for an extended period of time (72 hours or more), do not fill and
commission the HydroTap until ready for first use.
10. For water taste and quality reasons, following any non-use period of more
than 72 hours, Zip recommends to perform a system flush. Failure to flush
the system may affect water quality.
11. Due to the process of continuous improvement, Zip Water reserves the
right to change details mentioned in this manual, without notice.
!

Page 8 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Major Components and Accessories
Parts supplied Description
1 x Tap option with
hoses
(Classic tap shown)
1 X HydroTap
Command Centre
with air and water
filters
1 X Mains water
connection hose
1 x Connector +
Strainer Sub-assy
Duct kit
1 x Air Duct
1 x Mounting plate
Vent Kit
1 x Kickboard louvre
1 x Door vent louvre
1 x Front vent grill
1 X HydroTap Booster
Heater & hoses.
(Supplied with
240 /175 models)
1 x Flow Restrictor
and Tee piece for
Mixer taps and select
models
1 x Mixer Tap
for 4-In-1 and select
models (with hoses)
(Arc tap shown)
1 x Installation
Instructions
(this book) and
1 x User Guide
Accessories Description
HydroTap Booster
Water System with
connection hoses
Softener
and head assembly
Font Kit for
Arc & Cube Models
Font Kit for Classic &
Elite Models
Replacement Filter
Disabled Lever Kit
BC 4-in-1 Upgrade
Kit
Vent Tray
93540
Install
Instruct
User
Guide

801314 v3.05 09.20 HT BC Commercial Instructions Page 9 of 28
Technical Specifications
Model
Cups of
Boiling
Water per
Hour
Glasses of
Chilled Water
per Hour
BC 160 125
NoteNote :
• The Cup measurement =167mL and the Glass measurement = 200mL.
• Chilled water will continue to be dispensed after the rated capacity has been used, although this may be
at slightly higher temperature.
Products covered by these instructions:
** Add an extra 5 kg when full of water
Capacity
Boiling
(cups)
Capacity
Chilled
(glasses)
Boost
(10A)
Power
outlets
required
Power
Rating
(kW)
Boost
Rating
(kW)
Unit Dimensions
W x D x H (mm)
with air duct
**Dry
Weight
(kg)
Boiling Chilled
BC160/125 160 125 no 1x10A 2.1 — 450 x 470 x 335 23
BC160/175 160 175 no 1x10A 2.2 — 450 x 470 x 335 23
BC240/175 240 175 yes 2x10A 2.2 2.2 450 x 470 x 335 23
4 in 1
BCHA160/125 160 125 no 1x10A 2.1 — 450 x 470 x 335 23
BCHA160/175 160 175 no 1x10A 2.2 — 450 x 470 x 335 23
BCHA240/175 240 175 yes 2x10A 2.2 2.2 450 x 470 x 335 23
All in One
AV160/125
A 160 /125 160 125 no 1x10A 2.1 — 450 x 470 x 335 23
AV160/175
A 160 /175 160 175 no 1x10A 2.2 — 450 x 470 x 335 23
AV240/175
A 240 /175 240 175 yes 2x10A 2.2 2.2 450 x 470 x 335 23
Commercial Models
BC Boiling and Chilled
BCHA 4 in 1
A All in One - Mains
AV All in One - Vented
D Disabled lever controls (optional accessory)

Page 10 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Before Installation
Before installing ensure that the following have been provided at the
Installation site:
• Review all the technical specifications.
• Ensure the underbench can support the product weight when full of water,
(allow an extra 5kg when full. )
• Sufficient space in the cupboard to install the Command Centre in accordance with these Installation
Instructions. Refer to technical specification for dimensions. Make allowance for a booster heater and
/ or water softener if required. Refer to section 3 & 4, for Installation instructions.
• For Zip HydroTap 160/125 &160/175 models, a 220-240V, 10A AC power outlet will be required. For
Zip HydroTap 240/175 models, two 220-240V, 10A AC power outlets will be required (one power
outlet for the Zip HydroTap and the other for the Booster heater).
NoteNote: Check all cable and hose lengths against inlet /outlet positions before proceeding
(See section 5 for general layout).
• A potable water supply connection with isolating valve inside the cupboard within reach of the braided
hoses and positioned so that the connection point and the stop cock will not be obstructed when the
Command Centre is installed.
• For the mains pressure All-in-One tap, an external hot and cold water supply will be required.
• If an external filtration or water softening device is required, then it is important to allow extra space
for these items.
• A cold water supply with a minimum working pressure of 150kPa (200kPa when a booster and /or
filter softener is fitted) and a maximum working pressure of 700kPa connected via an isolation valve.
• The fitting of an air flow duct, attached to the right hand side of the Command Centre, requires a
rectangular cut size of 284mm x 45mm, to provide adequate warm air displacement. See section 2.
• The appliance must be placed with its base in a horizontal position.
IMPORTANT! Do not proceed with the installation if these requirements are not met.
!
Special Tools Required:
In addition to normal tools, the following will be required:
For the standard and Mixer taps:
• 35mm diameter sheet metal hole punch for sink tops (not supplied)
• 35mm diameter hole saw for timber bench tops (not supplied)
• Nut runner tube spanner (supplied) for fixing tap assembly.
For the All-In-One tap:
• 50mm diameter sheet metal hole punch for sink tops (not supplied)
• 50mm diameter hole saw for timber bench tops (not supplied)
• Nut runner tube spanner (supplied) for fixing tap assembly.

801314 v3.05 09.20 HT BC Commercial Instructions Page 11 of 28
2.1 All Models
Proper air circulation must be provided for all Boiling and Chilled models. The system will operate correctly
only if the recommended air gaps are achieved during Installation. The vent duct and louvre panels must be
installed for all under floor and /or door vent systems, as instructed.
**Note: Inlet and outlet vents should be separated by a minimum of 100mm, to avoid hot air recirculation.
IMPORTANT: Allow clearance of 50mm either side, and 200mm above the Command Centre.
!
When installing air flow ducts, the following tools will be required:
• Jigsaw and 12mm Drill
• Keyhole or Wall Board saw.
Section 2
Ventilation
Cool Air IN
via cabinet
floor, front
vent grille
Warm Air OUT
via kickboard louvre
Recommended Installation showing the correct air flow
**MIN.
100mm
Section 1
Tap Installation
Refer to the Tap installation instruction book 803341.
Note:
- Mains hose
length is 750mm
- Plug and Cord
length is 1800mm
Position the
Command Centre
close to the outlet
tap, within reach of
the hose and cord
lengths supplied
Note:Note: the hosesthe hoses
need to have aneed to have a
constant downwardconstant downward
gradient to the Hy-gradient to the Hy-
droTap to allow alldroTap to allow all
water to drain backwater to drain back
into the tanks.into the tanks.
Min.
50mm
air gap

Page 12 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Ventilation
= =
max 43
314.00
12.00
12.00
285.00
12.00
5
326.00
CUT OUT DETAILS
A
A - KICKBOARD CUT-OUT
1. Drill 4 pilot holes Ø12 in corners
2. Finish cut-out using Jigsaw
and Keyhole or Wall Board saw
B - CABINET FLOOR
CUT-OUT
1. Drill two pilot holes Ø12
2. Finish cut-out using Jigsaw
C - CABINET FLOOR
CUT-OUT
1. Drill 4 pilot holes Ø12 in corners
2. Finish cut-out using Jigsaw
and Keyhole or Wall Board saw
NOTE: Ensure that
Cut-outs 'A' and 'B' are on opposite side of cabinet.
Cut-out 'C' is straight behind 'A'
60.00
BC
12.00
45.00
284
285.00
12.00
60.00
WALL OR DOOR CUT-OUT
228
12
98
AIR OUTLET CUT-OUT
Min 450mm
For positioning of cut-out C, use the
template marked on the cardboard carton
The following instructions are critical if the vent kit, as supplied, cannot be fitted:
If the kick board vent kit cannot be used then it is important to fit a HydroTap vent tray, which ensures heat
dissipation through the installed vent tray. For high use applications, where the cupboard space temperature
is near 35°C, or higher, an auxiliary fan kit may be fitted. Contact your local service centre for availability.
• Vent tray, part no. 93540 (optional accessory)
• Dual exhaust fan kit, part no. 93156 (optional accessory)
!
HydroTap G4 on Vent Tray
Vent Tray
Dual Exhaust Fan Kit
Vent Tray Kit

801314 v3.05 09.20 HT BC Commercial Instructions Page 13 of 28
Booster Specifications:
Rating Unit
Nominal Power Rating 2.2 kW
Nominal Current 10 A
Electric Supply 50Hz AC 230 V
Elect ex and plug (black) - 1 metre length (with 90º Australian plug) 10 A
Fixed Flow Rate 1.2 L/min
Minimum water pressure 200 kPa
Section 3
Booster Heater
Mount base
Horizontally
3.1 Product Description
The boost unit is a compact electronically
controlled auxiliary water heater. It is intended to
provide pre heating of water before it enters the
Zip HydroTap G4 boiling tank. The Booster is
supplied as standard equipment with all 240 cup
models. However, it may be later installed, as an
accessory for the 160 cup models, to increase
their delivery to 240 cups.
400mm
NoteNote 1: water connection
Blue marking: water in
Red marking: water out.
The braided hoses cannot be length-
ened.
NoteNote 2: The electrical cable length
is 1.0 metre.
NoteNote 3: Position the Booster within
reach of the fixed hose lengths, keep-
ing the Booster as close as possible
to the Command Centre inlet/ outlet
fittings.
NoteNote 4: Ensure the Booster heater
is mounted in an upright position (as
shown) with a horizontal base.

Page 14 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Booster Installation
3.2 Installation Procedure
Site requirements
• The appliance must only be installed in a frost-free area. Never expose the appliance to frost.
• The appliance is designed for wall mounted installation and must to be installed with water connectors
facing upwards.
• The appliance complies with protection class IP 25.
• The 400mm braided hoses supplied with the Command Centre cannot be lengthened.
• The 90°elbow hose ends should be fitted to the inlet and outlet connections on top of the Booster.
• The hot water outlet hose must be thermally insulated with the insulation provided.
Tilt Forward Lift UP
Release
NoteNote: Remove the backing plate for wall mounting
3.3 To Remove / Install the appliance
1. Insert a flat head screwdriver all the way into the lock.
2. Gently angle the screwdriver upwards by approximately 10° as shown in the image below.
3. Pull the appliance forwards by approximately 15° as shown.
4. Carefully pull the appliance upwards to complete the removal process, taking care not to break the
lower clips
5. To install: place the appliance on the wall bracket and snap into position (see illustration below).
Take care not
to break the
lower clips when
removing or
installing the
Booster
!
Installation

801314 v3.05 09.20 HT BC Commercial Instructions Page 15 of 28
NoteNote 1: This appliance is intended for use with the Zip HydroTap Command Centre.
NoteNote 2: Water connections must be pointing vertically upwards.
NoteNote 3: The booster unit should be installed as close as possible to the Zip HydroTap
Command Centre as the 400mm connection hoses cannot be lengthened.
Booster System
3.4 Braided hose connection s
1. The cold water inlet (blue) and hot water outlet (red) are marked on the rating plate. Connect the
braided hoses from the ‘Bypass Out’ fitting on the Zip HydroTap, to the water inlet of the booster unit
(Marked Blue) and from the outlet of the booster unit (Marked Red) to the ‘Bypass IN’ fitting on the
Zip HydroTap Command Centre. Avoid exerting any mechanical pressure on the appliance. This can
be achieved by applying a spanner on the flats of the inlet and outlet connections when tightening
the braided hose connectors. Do not over tighten! Tighten the braided hoses by hand, then turn an
additional 90°- 180° with a spanner
2. Once the water connections have been made, check for any leaks and rectify as necessary.
Hot Water
Connection
(outlet, G1/2”)
Strainer
Cold Water
Connection
(inlet, G1/2”)
Hold the hexagon while
tightening the braided
hose fittings
Braided Hoses

Page 16 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Section 4
Filter / Softener Installation
An optional, external limescale filter / softener may be fitted to reduce the incidence of scale build up in the
hot tank.
• Choose a suitable location, (cupboard back or side wall)
within the reach of the braided hoses.
• Mount the filter head bracket in an upright position, using the
screws supplied in the kit
• Ensure there is enough headroom for the filter cartridge to be
easily fitted and removed. *Allow a Min 80mm base clearance
• Attach the hoses as shown in section 5.3 - 5.7. Noting the flow
directions as marked on the filter head.
4.1 Mounting the filter head
*Min. 80mm
Clearance
4.2 Cartridge Installation
1. Unpack replacement cartridge, write today’s date where
shown on the label and remove the sanitary cap.
2. Avoid touching the filter O-rings and filter opening as this may
cause bacterial contamination of the cartridge.
3. Moisten the O-rings with water, align the front cartridge label
to the left and push the new cartridge into the filter head.
4. Turn the cartridge a quarter turn to the right until the cartridge
comes to a complete stop, with the front label facing forward.
5. Disconnect the filter outlet hose from the Command Centre
and direct the hose end into a container ready for flushing.
6. Turn the power and water ON and depress the tap’s Boiling
lever and allow water to run for 30 seconds to flush the tank.
7. Allow at least 10L to flow through the filter to ensure all
carbon particles have been flushed.
8. Turn the power and water off (after flushing 10L).
9. Reconnect the filter outlet hose to the Command Centre.
10. Turn the water supply back on and check for leaks.
11. Set the appropriate selection on the Internal Filter Bypass
valve located at the rear of the Command Centre in
accordance with Sections 5.2.
Filter Label
Inlet
Outlet

801314 v3.05 09.20 HT BC Commercial Instructions Page 17 of 28
Before you install an Command Centre, determine whether a water softener or an external filter is required.
5.1 External Bypass Valve
The diverter bypass valve allows the user to choose to have the boiling feed water bypass the internal filter
and only be filtered by external filtration. The diverter valve is located at the rear panel of the Zip HydroTap
Command Centre on the filter door side. Refer to the image below to determine the correct valve position.
Section 5
Command Centre Installation
5.2 Hose and tube fitting
• Remove all caps from the top of the Command
Centre (except the mixer caps)
• Install the mains water braided hoses to the
Command Centre before locating the unit in
place.
NOTE: Do not overtighten
John Guest fittings (Insertion and removal)
Be careful when cutting the poly tube so that there are no rough edges and that the tube is not distorted.
1. Use a sharp knife to ensure the tube has a clean,
straight edge. Do not cut at an angle.
2. Remove any swarf or unwanted material.
3. Push the tube into the John Guest fitting making sure
all connections to the John Guest fittings are pushed
in past the “O”ring to full depth, at least 15-16mm.
4. Check for a good joint by pulling back on the tube. If
the tube comes out, of the fitting, repeat the above
step.
5. To remove the tube, press the collet into the fitting
and at the same time pull back on the tube.
B
Rotate 90°
only
1
2
3
4
If no external lter
is installed, select
position A.
If an external filter
is installed, select
position B
A
Rotate 90°
only
1
2
3
4
Connector + Strainer
90° Bend end
of Braided Hose
To HydroTap
Command Centre
Braided hose for
Mains Water Supply
From Mains
Water Supply

Page 18 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Installation Instructions
: Not required for standard BC HydroTap models.
394mm
RED
CLEAR
BLUE
BRAIDED
Min.
70mm
USB CHILLED
OUTLET
MAINS
IN
MIXER
OUT
MIXER
IN
BOILING
OUT
BYPASS
IN
VENT BYPASS
OUT
5.3 Models BC 160/125 and BC 160/175
Note:
- Mains hose
length is 750mm
- Plug and Cord
length is 1800mm
Position the
Command Centre
close to the outlet
tap, within reach of
the hose and cord
lengths supplied
Note:Note: the hosesthe hoses
need to have aneed to have a
constant downwardconstant downward
gradient to the Hy-gradient to the Hy-
droTap to allow alldroTap to allow all
water to drain backwater to drain back
into the tanks.into the tanks.
NOTE: The tube lengths are matched to the pump performance and therefore CANNOT be lengthened
Min.
50mm
Max.
1000mm

801314 v3.05 09.20 HT BC Commercial Instructions Page 19 of 28
Installation Instructions
Booster
RED
CLEAR
BLUE
BRAIDED
5.4 Model BC 240/175
Booster
option
USB CHILLED
OUTLET
MAINS
IN
MIXER
OUT
MIXER
IN
BOILING
OUT
BYPASS
IN
VENT BYPASS
OUT
Note:
- Mains hose
length is 750mm
- Plug and Cord
length is 1800mm
Position the
Command Centre
close to the outlet
tap, within reach of
the hose and cord
lengths supplied
Note:Note: the hosesthe hoses
need to have aneed to have a
constant downwardconstant downward
gradient to the Hy-gradient to the Hy-
droTap to allow alldroTap to allow all
water to drain backwater to drain back
into the tanks.into the tanks.
: Not required for standard BC HydroTap models.
NOTE: The tube lengths are matched to the pump performance and therefore CANNOT be lengthened

Page 20 of 28 801314 v3.05 09.20 HT BC Commercial Instructions
Installation Instructions
Booster
RED
CLEAR
BLUE
BRAIDED
5.5 Model All-In-One Mains Pressure
Booster
option
USB CHILLED
OUTLET
MAINS
IN
MIXER
OUT
MIXER
IN
BOILING
OUT
BYPASS
IN
VENT BYPASS
OUT
Note:
- Mains hose
length is 750mm
- Plug and Cord
length is 1800mm
Position the
Command Centre
close to the outlet
tap, within reach of
the hose and cord
lengths supplied
Note:Note: the hosesthe hoses
need to have aneed to have a
constant downwardconstant downward
gradient to the Hy-gradient to the Hy-
droTap to allow alldroTap to allow all
water to drain backwater to drain back
into the tanks.into the tanks.
: Not required for standard BC HydroTap models.
NOTE: The tube lengths are matched to the pump performance and therefore CANNOT be lengthened
NOTE: to activate the filter, flush at least 10L of water through the filter before connecting to a softener or to
a Booster heater.
Tee piece
(Supplied)
External HOT and
COLD isolation valves
(not supplied)