make your home smart www.zipato.com make your home smart www.zipato.com 02
POWER UP PROCEDURE
This device supports the Z-Wave firmware update via OTA. Put
the controller into the firmware update mode, and then press the
button once to start the update. Please don’t remove the battery,
otherwise it will cause the firmware fail, and the device will cease
to function. After update is complete, it is recommended that the
user powers up the device.
Caution: After removing battery, please wait about 30 seconds, and
then re-install the battery.
SECURITY NETWORK
This device supports the security function. When the device is
paired with security controller, it will auto switch to the security
mode. In security mode, the following commands need to be
wrapped in Security Command Classes to properly communicate,
otherwise there will be no response.
COMMAND_CLASS_BATTERY
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_SENSOR_BINARY_V2
COMMAND_CLASS_WAKE_UP_V2
TEST ALARM
Test the sensor by pushing firmly on the test button for around
2 seconds until the horn sounds, the sound pattern is 3 beeps,
pause, and then 3 beeps with red LED flashing continuously
and rapidly, and the controller will receive Smoke alarm test
notification. If the Smoke Sensor beeps three times with yellow
LED flashing three times in 43 seconds, it indicates the Smoke
Sensor is not working properly, it requires to be repaired. This is
the only way to make sure that the Smoke Sensor device is working
properly. If the device fails to test properly, have it repaired or
replaced immediately. If you suspect that your Smoke Sensor does
not go into alarm, test it by pressing the test button to ensure if it
works properly.
Notice: To make sure the Smoke Sensor is in good working
condition, weekly testing is highly reccommended.
TAMPER SWITCH FEATURE
If the Smoke Sensor is not mounted into the bracket properly, the
tamper function is triggered and the yellow LED is steadily on. You
will hear temporal three sound with yellow LED steadily on until
Smoke Sensor is mounted back into bracket properly.
ZWAVE CONFIGURATION SETTINGS
Notice:
For all of the configuration parameters, the data size is 1.
The configuration marked with starV (*), means that after the
removing the device, setting will still keep, without reverting back
to factory settings, unless the user executes the “RESET”
procedure.
The reserve bit or not supported bit is allowed any value, without
effects.
NO. NAME DEF. VALID DESCRIPTION
7 (*) Customer
Function
4All Customer function switch,
using bit control
0Bit0: Reserve
0Bit1: Reserve
1Bit2: Reserve
0
Bit4: Notification type
0: Using Notification
Report
1: Using Sensor Binary
Report
0Bit5: Reserve
0Bit6: Reserve
0Bit7: Reserve
Association
1. Have Z-Wave Controller entered association
mode.
2. Pressing test button three times within 1.5
seconds to enter the association mode.
Note: The device support 1 groups. This group is
for receiving the report message, like triggered
event etc. This group support 8 nodes maximum.
Failed or success in add/remove the node ID can be viewed
from Z-Wave Controller.
Notice: Always reset a Z-Wave device before trying to add it to a
Z-Wave network.
Notice: When the device is into NWI mode, the sensor
functionality will be disabled. The NWI mode will timeout after 30
seconds. You can press the button 3 times to abort the NWI mode.
ZWAVE NOTIFICATION
After device is added to the network, it will wake-up once per
day by default. When it wakes-up it will broadcast the “Wake Up
Notification” message to the network, and wake-up 10 seconds
to receive the setting commands. The wake-up interval minimum
setting is 30 minutes, and maximum setting is 120 hours. Interval
step is 30 minutes. If you want to wake-up device immediately, please
press the button once. The device will wake-up for 10 seconds.
ZWAVE MESSAGE REPORT
When Smoke Sensor detects, the device will report the trigger event
and also report the battery status. By default the device will be using
Notification Report to represent the trigger event. It can be changed
to Sensor Binary Report by setting the configuration NO. 7 Bit4 to 1.
Smoke Detected/Test Report:
When the Smoke Sensor detects smoke, the device will unsolicitedly
send the smoke detected (0x02) report to the nodes in the group 1.
When the device is in alarm test mode, the device will unsolicitedly
send the Smoke Sensor test (0x03) report to the nodes in the group 1.
NOTIFICATION REPORT V4
Notification Type: Smoke (0x01)
Event: Smoke detected, Unknown Location (0x02)
Smoke Alarm Test (0x03)
SENSOR BINARY REPORT V2
Sensor Type: Smoke (0x02)
Sensor Value: 0xFF
Tamper Report:
When the tamper is pressed, the device will fall into the alarm
state. In that state, if tamper is released, the yellow LED will light
up and the device will unsolicitedly send the report to the nodes
in the group 1.
NOTIFICATION REPORT V4
Notification Type: Home Security (0x07)
Event: Tampering. Product covering removed (0x03)
SENSOR BINARY REPORT V2
Sensor Type: Tamper (0x08)
Sensor Value: 0xFF
Notice : When the event is triggered, the device will report the
messages to the nodes in the group 1. These messages also
include the tamper status.
POWER UP PROCEDURE
NWI
When the device powers on, it will check if it is already added to the
network. If it isn’t, press the button to start the NWI mode. Until
timeout or successful inclusion of device by controller. NWI mode
can be aborted by pressing the button 3 times.
Wake
When the device powers on, the device will wake-up for about 20
seconds. During this time, the controller can communicate with
the device. Normally the device is always sleeping to save the
battery energy.
UNDER PART 1 OF THE CONSUMER PROTECTION ACT 1987
OF THE UNITED KINGDOM. SOME STATES OR COUNTRIES DO
NOT ALLOW: (1) A DISCLAIMER OF IMPLIED WARRANTIES; (2)
A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS
OR THE EXCLUSION; OR (3) LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS.
IN SUCH STATES OR COUNTRIES, SOME EXCLUSIONS OR
LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO
YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY
FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY. YOU
ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY
LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.
This Limited Product Warranty applies to ZIPATO branded hardware
products (collectively referred to as “ZIPATO Hardware Products”)
sold by ZIPATO (Europe), its European subsidiaries, affiliates,
authorized resellers, or country distributors (collectively referred to
as “ZIPATO Resellers”) with this Limited Product Warranty.
The term “ZIPATO Hardware Product” is limited to the hardware
components and all its internal components including firmware.
The term “ZIPATO Hardware Product” DOES NOT include any
software applications or programs.
GEOGRAPHICAL SCOPE OF THE LIMITED
PRODUCT WARRANTY
This Limited Product Warranty is applicable to Hardware Products
sold by Zipato Resellers in all countries listed at the beginning of
this document under the heading “Countries in which this ZIPATO
Limited Product Warranty applies”. The Limited Product Warranty
will be honored in any country where ZIPATO or its authorized service
providers offer warranty service subject to the terms and conditions
set forth in this Limited Product Warranty. However, warranty
service availability and response times may vary from country to
country and may also be subject to registration requirements.
LIMITATION OF PRODUCT WARRANTY
ZIPATO warrants that the products described below under
normal use are free from material defects in materials and
workmanship during the Limited Product Warranty Period set
forth below (“Limited Product Warranty Period”), if the product is
used and serviced in accordance with the user manual and other
documentation provided to the purchaser at the time of purchase
(or as amended from time to time).
ZIPATO does not warrant that the products will operate
uninterrupted or error-free or that all deficiencies, errors, defects
or non-conformities will be corrected.
This warranty shall not apply to problems resulting from: (a)
unauthorized alterations or attachments; (b) negligence, abuse
or misuse, including failure to operate the product in accordance
with specifications or interface requirements; (c) improper
handling; (d) failure of goods or services not obtained from ZIPATO
or not subject to a then-effective ZIPATO warranty or maintenance
agreement; (e) improper use or storage; or (f) fire, water, acts of
God or other catastrophic events. This warranty shall also not
apply to any particular product if any ZIPATO serial number has
been removed or defaced in any way.
ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A
RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR
THE ZIPATO HARDWARE PRODUCT.
LIMITED PRODUCT WARRANTY PERIOD
The Limited Product Warranty Period starts on the date of
purchase from ZIPATO. Your dated sales or delivery receipt,
showing the date of purchase of the product, is your proof of the
purchase date. You may be required to provide proof of purchase
as a condition of receiving warranty service. You are entitled to
warranty service according to the terms and conditions of this
document if a repair to your ZIPATO branded hardware is required
within the Limited Product Warranty Period.
[Other than in respect of products for domestic use (in particular
those listed in the first and last boxes in the table below), this
Limited Product Warranty extends only to the original end user
purchaser of this ZIPATO Hardware Product and is not transferable
10
Auto
Report
Battery
Time
12 0~127
The interval time for auto
report the battery level.
0 means turn off auto
report battery. Each tick
means 30 minutes. The
default value is 12(6 hours)
ZWAVE COMMAND CLASSES
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_SENSOR_BINARY_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_SECURITY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
TROUBLESHOOTING
Having trouble installing your new product?
Zipato’s website contains the latest user documentation and
software updates for Zipato products and services:
www.zipato.com
You can also find answers in the Zipato Community at:
community.zipato.com
LIMITED PRODUCT WARRANTY
GENERAL TERMS
Nothing in this Limited Product Warranty affects your statutory
rights as a consumer.
The Limited Product Warranty set forth below is given by Tri plus
grupa d.o.o. (Europe) (herein referred to as “ZIPATO”). This Limited
Product Warranty is only effective upon presentation of the proof
of purchase. Upon further request by ZIPATO, this warranty card
has to be presented, too.
EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,
ZIPATO MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. ZIPATO EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED
BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY
PERIOD. TO THE EXTENT ALLOWED BY LOCAL LAW, THE
REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S
SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO. THEY DO
NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU HAVE
AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM.
IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR
INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING
LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED
IN CONTRACT, TORT, OR OTHERWISE. HOWEVER, NOTHING
IN THIS AGREEMENT LIMITS ZIPATO’S LIABILITY TO YOU (I) IN
THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT
RESULTING FROM ZIPATO’S NEGLIGENCE, OR (II) TO THE EXTENT
RESULTING FROM ANY FRAUDULENT MISREPRESENTATION
ON THE PART OF ZIPATO, OR (III) TO THE EXTENT ARISING
