Zipato ZIPABOX-BACKUP-V5 User manual

DECLARATION OF CONFORMITY
Tri plus grupa d.o.o. declares that this product is in compliance
with the essential requirements and other relevant provisions of
Directives as follows:
Model: ZIPABOX-BACKUP-V5
Intented use: indoor
EMC Directive (2004/108/EC)
Low Voltage Directive (2006/95/EC)
R&TTE Directive (1999/5/EC)
The product is compatible with following norms/standards:
EN 60950-1:2007+A11:2009+A12:2011
EN 301 489-17 V2.1.1:2010
EN 301 489-3 V1..4.1:2003
EN 301 489-1 V1.8.1:2008
EN 300 328 V1.7.1:2008
EN 50130-4:1977+A1:2000+A2:2004
EN 300 220-1 V2.1.1:2006
EN 300 220-2 V2.1.2:2008
Manufacturer/Authorised representative,
Dean Janacek
Zagreb, 12 September 2012
Backup expansion module
Tri plus grupa d.o.o.
Banjavciceva 11
10000 Zagreb
Croatia

COMPATIBILITY
This expansion module is designed to work only with Zipabox with
software version 0.9.962 or later.
HANDLING
Do not drop, knock or shake the module. Rough handling can break
internal circuit boards and connectors.
ENVIRONMENT
Do not expose the module to excessive heat or cold, as it can damage or
shorten the life of electronic circuit boards and battery.
If possible, dispose this module at a recycling center. Do not dispose of
this module with the household waste.
SPECIFICATION
Power supply: from Zipabox
Operating temperature: -10° ~ +40° C
Operating humidity: 5 ~ 95% RH
Dimensions: 55 x 87 x 46 mm
Weight: 205g
Battery: 3500 mAh, 7.4 V
Port: USB, RS232
UNPACKING
Backup expansion module consists of:
1x expansion module
1x GSM stick (optional)
• Connect GSM stick to USB port of the Backup module (optional).
• Optional RS232 connection:
CONNECTING DEVICE
1. Disconnect Zipabox from power;
2. If you had any other module in Slot 1 remove it;
3. Align connector of Backup expansion module to expansion Slot
1 of Zipabox;
4. Join module and Zipabox together until gap between them is
completely closed;
5. If you had any other module in Slot 1 connect it back to Backup
module in a same way.
INSTALLATION/MOUNTING
Mount together with Zipabox.
TESTING
1. Battery in Backup module comes charged
2. When Backup module is first time connected to Zipabox upper
LED is red indicating battery is discharging
3. When ZipaBox is connected back to power supply upper LED will
become green
4. When battery is charging lower LED is blue
5. The lower LED slow blinking in blue indicates battery error.
REPARING
Do not attempt to repair this product. There are no user-serviceable parts
inside.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry. Moisture will corrode the
inner electronics.
CLEANING
Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning
solvents or strong detergents.
COPYRIGT
The contents of this manual is subject to copyright protection. Copying and
reproducing is prohibited without prior written permission. Information in
this document is subject to change without prior notice. Check
www.zipato.com for updates.
TX
RX
GND
RS232
Pinout

DECLARATION OF CONFORMITY
Tri plus grupa d.o.o. declares that this product is in compliance
with the essential requirements and other relevant provisions of
Directives as follows:
Model: ZIPABOX-ZIGBEE-V1
Intented use: indoor
EMC Directive (2004/108/EC)
Low Voltage Directive (2006/95/EC)
R&TTE Directive (1999/5/EC)
The product is compatible with following norms/standards:
EN 60950-1:2007+A11:2009+A12:2011
EN 301 489-17 V2.1.1:2010
EN 301 489-3 V1..4.1:2003
EN 301 489-1 V1.8.1:2008
EN 300 328 V1.7.1:2008
EN 50130-4:1977+A1:2000+A2:2004
EN 300 220-1 V2.1.1:2006
EN 300 220-2 V2.1.2:2008
Manufacturer/Authorised representative,
Dean Janacek
Zagreb, 12 September 2012
Tri plus grupa d.o.o.
Banjavciceva 11
10000 Zagreb
Croatia