zipLink ZL-RFU20 User manual

TB3
TB1
TB2
P1
1
13
12
24
Cable Connector
COM
1
11
10
20
F5 F6 F7 F8 COM F13 F14 F15 F16
COM F1 F2 F3 F4 COM F9 F10 F11 F12
Load
Distribution
Load
Distribution
F1 F2 F3 F4 F9 F10 F11 F12
F5 F6 F7 F8 F13 F14 F15 F16
Press
and turn
cap CCW.
Fuse Replacement
Remove
Push fuse
into holder
Install
Press
and turn
cap CW.
Secure
16-Point Fuse Module
Installation Instructions ZL-RFU20
Specifications
Descr pt on* 16-point fuse connector module
Operat on Voltage 0-250VAC 0-75VDC***
UL Rated Current** 1A per point
Max mum Current per C rcu t 2A
Max mum Current per Module 32A
Number of C rcu ts 16
F eld to Log c S de Isolat on 1800VAC applied for 1 second
Insulat on Res stance >10M Ω@ 500VDC
Surround ng Temperature Range 32 to 140°F (0 to 60°C)
Approvals File # E200031 UL, cUL, Class 1, Division 2,
Groups A,B,C,D Hazardous Locations,
CE, EN 61131-2:2007
Term nal Block Contacts Copper alloy, tin-lead plated
W re Range (Rated Cross Sect on)** 12-24AWG Solid or Stranded Copper Conductor
(2.5mm²)
W re Str p Length 0.24-0.27” (6-7mm)
Screw Torque 4.4 in-lbs (0.5 Nm)
Fuses (Not Included) Sixteen 5x20mm, 250V
Replacement Fuse See Edison 5x20mm Glass Fuse section range up
to a Max. 2 amp fuse
D mens ons (WxHxD) 7.21” x 3.42” x 2.25” (183mm x 86.8mm x 57.2mm)
Connector Type Molex Micro-Fit 3.0, 24 pin connector, example re-
ceptacle 43020-2400, ins 43031 Series, Male
Cable/W re Clearance 0.5” (12.7mm) Required
Mount ng Restr ct ons None
Typical Wiring for D2-16TD1-2
Typical Wiring when used with
D2-16TD2-2, D2-12TA, D2-12TR.
TB3
TB1
TB2
1
11
10
20
C4567C4567
+24 0123NC 0123
Load
Load
Load
Load
+V
10.2 - 26.4VDC
-V
TB3
TB1
TB2
1
11
10
20
Load
Load
Load
Load
Refer to I/O module for power source requirement.
Refer to I/O module for power source requirement.
C4567C4567
NC 0123NC 0123
6
3
4
1
P1 1 12
13 24
20
10
11
1
TB2
6
3
4
1
F14
F10
F13
F9
F7
F3
F5
F1
TB1
F2
F6F8
F4
F15
TB3
F11 F12
F16
7.21” [183.0mm] 2.25” [57.2mm]
3.42”
[86.8mm]
LOAD
DISTRIBUTION
2.30” [58.4mm]
Terminal Block
Insertion Point
pening
Dimension
ZL-RFU20 TB2 Pinouts
Row P n Fuse Term nal
T
O
P
2, 14 -------- 1
15 Fuse 5 2
16 Fuse 6 3
17 Fuse 7 4
18 Fuse 8 5
8, 20 -------- 6
21 Fuse 13 7
22 Fuse 14 8
23 Fuse 15 9
24 Fuse 16 10
B
O
T
T
O
M
1, 13 -------- 11
3 Fuse 1 12
4 Fuse 2 13
5 Fuse 3 14
6 Fuse 4 15
7, 19 -------- 16
9 Fuse 9 17
10 Fuse 10 18
11 Fuse 11 19
12 Fuse 12 20
0.114"
[2.9 mm]
0.098"
[2.5 mm]
*Connecting cables are for internal wiring only.
**Use Conductors rated 60°/75°C.
***UL rated 0-75VDC applies when using a DC rated fuse (not supplied), example 217 series.

1Find correct label and remove from sheet
Note: Upper and
Lower designation
Choose I/O
module type
|C2|X5|X6|X7|X8|Y4|C4|Y
|
C2
|
X5
|
X6
|
X7
|
X8
|
Y4
|
C4
|
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
2Apply label to designated position
Upper
Lower
Apply ZIPLink Labels
(Supplied with ZIPLink cables)
To install ZIPLink module, insert upper tab
into DIN rail.
Rotate
until
firmly seated
Click
DIN Rail Installation
and Removal
Repeat for Tab 2.
Tab
1
Tab
2
and locked
on DIN rail.
To remove ZIPLink
module, insert
screwdriver
between Tab 1
and module.
Pry up
to release
clip from DIN rail.
Note: For
cable/wire
clearance
requirements see
specifications.
ZIPLink Cable Removal
2Pull connector
from socket.
1
Push tab on
raised tip
and hold.
3505 Hutchinson Road, Cumming GA 30040
1-800-633-0405 www.automationdirect.com
Copyright 2011, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate the
installation and operation of your equipment. These codes vary from
area to area and it is your responsibility to determine which codes
should be followed, and to verify that the equipment, installation, and
operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from
the failure to follow all applicable codes and standards. We do not
guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for
your product design, installation, or operation.
If you have any questions concerning the installation or operation
of this equipment, or if you need additional information, please call
Technical Support at 770-844-4200.
This publication is based on information that was available at the
time it was printed. At AutomationDirect.com® we constantly strive to
improve our products and services, so we reserve the right to make
changes to the products and/or publications at any time without notice
and without any obligation. This publication may also discuss features
that may not be available in certain revisions of the product.
16-Point Fuse Module
Installation Instructions ZL-RFU20
HAZARD WARNING
A. THIS EQUIPMENT IS SUITABLE F R USE IN CLASS I, DIVISI N 2/Z NE 2, GR UPS A, B,
C AND D R N N-HAZARD US L CATI NS NLY.
B. WARNING – EXPLOSION HAZARD – SUBSTITUTI N F C MP NENTS MAY IMPAIR
SUITABILITY F R CLASS I, DIVISI N 2/Z NE 2.
C. WARNING – EXPLOSION HAZARD – D N T C NNECT R DISC NNECT C NNEC-
T RS R PERATE SWITCHES WHILE CIRCUIT IS LIVE UNLESS THE AREA IS KN WN T
BE N N-HAZARD US.
D. ALL M DULES USED WITH ACCESS RIES MUST USE R/C (ECBT2) MATING PLUG F R ALL
APPLICABLE M DELS. ALL MATING PLUGS SHALL HAVE SUITABLE RATINGS F R DEVICE.
6/18/2013 Document # ZL-RFU20 Rev6