Zippity ZP19052 User manual

1
www.zippity-outdoor.com
ASSEMBLY
INSTRUCTIONS
LIBERTY LATTICE AC
SCREEN KIT
45 MIN approximate assembly
time for 3 panels
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
@

2www.zippity-outdoor.com
GENERAL INFORMATION
IMPORTANT
•Please read through before starting assembly.
• Important: Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
CALL US FIRST SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur.
If you discover any missing, damaged or defective parts, please contact our customer service department.
EMAIL: [e-mail]
PHONE: [phone]
Customer service agents are available to take calls weekdays from 8am-5pm EST.
To help you quickly and accurately, please have reference item number ZP19052 and the specic part name which can be
found on the next page. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so
please give us a call at 704-892-5222 / 877-234-6196.
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help resolve your issues rst. If you still decide to
return the product, you will need to intitate the return from the company you originally purchased from.
@

3
www.zippity-outdoor.com
STEP 1: LAY OUT MATERIALS
LIBERTY LATTICE AC SCREEN KIT 3 PANEL
TOOLS YOU WILL NEED
Cordless Drill
Tape Measure
A
D
G
B C
E F
IH
J
K
Post Caps (6)
Horizontal Bottom Rail - Front (1)
1 ½” x 1 ½” x 36”
Horizontal Top Rail - Front (1)
1 ½” x 1 ½” x 36”
Horizontal Top Rail - Side (2)
1 ½” x 1 ½” x 36”
Horizontal Bottom Rail - Side (2)
1 ½” x 1 ½” x 36”
Horizontal
Picket (27) -
1 ¼” x ¼” x 33 ¼”
(marked with sticker
labeled “1”)
Vertical Picket (24) -
1 ¼” x ¼” x 35 ¾”
(marked with sticker
labeled “2”)
Posts (6) -
7
/ 8 ” x 1 ½” x 42”
End Caps (12)
(6 are installed,
6 are loose) ¾” Self-Augering
Stainless Steel Screw (24)
(for panel assembly)
4” Self-Tapping
Stainless Steel Screw (8)
(for connecting panels)

4www.zippity-outdoor.com
STEP 2: ASSEMBLE THE HORIZONTAL PICKETS
STEP 2.1 Identify the horizontal top rail - front (F) and the horizontal bottom rail - front (D) as shown below. Pressure t two
loose rail end caps (B) into the ends of each rail. Set these rails aside for now.
Top rail will be marked with two pre-
drilled holes on the top of the rail.
Front rails have no pre-drilled holes at these locations.
Side rails will have two pre-drilled holes on each end.
BF
D
STEP 2.2 STEP 2.3
Take two posts (G) and position them so
the routed holes face in towards each
other as shown.
1. Insert nine horizontal pickets (H) into the
routed holes in one of the posts.
2. Starting at one end of the opposite post,
guide the pickets into the routed holes in the
post.
NOTE: Identify the top of the screen by nding
the side of the post with pre-drilled hole 2 ¾"
from the end of the post.
2.75 in
2.75 in
4.75 in
4.75 in
G
1
2
H

5
www.zippity-outdoor.com
STEP 3: ATTACH THE VERTICAL PICKETS
STEP 3.2
STEP 3.1
Insert the eight vertical pickets (I) into the routed picket holes in the rail.
1. Take one of the horizontal bottom rails - front (D) and slide it up over the posts as illustrated. Ensure the routed
picket holes in the rail are facing up.
2. Align the pre-drilled holes in the posts and the rail.
3. Drive a ¾” screw (J) in each of the pre-drilled holes on the front and back of the rail (4 total).
NOTE: Vertical pickets will
have a sticker labeled "2".
I
1
23
Align
D
J

6www.zippity-outdoor.com
STEP 4: COMPLETE THE PANELS
STEP 4.1 1. Slide the horizontal top rail - front (F) over the posts ensuring the picket holes in the top rail are facing down.
2. Guide the pickets into the top rail and slide it down until the pre-drilled holes in the rail align with the holes in the
post.
3. Drive (4) ¾” screws into the aligned pre-drilled holes.
STEP 4.2 Repeat Steps 2-4 to create the other two screen panels. The other two panels will use side horizontal rails that
have extra holes at the ends.
Front panel has no
extra pre-drilled holes
1
23
Align
F

7
www.zippity-outdoor.com
STEP 5: CONNECT THE PANELS
STEP 6: INSERT THE POST CAPS
STEP 5.1
STEP 6.1
1. Take one of the two assembled side panels and place it at a right angle to the front panel as shown.
2. Drive (4) 4” screws (K) into the pre-drilled holes in the top and bottom rail.
3. Repeat this process on the other side with the third screen as shown below.
Insert (6) post caps (A) over the top of the posts to complete the screen.
NOTE: Ensure the screws are driven in straight.
13
2
K
Front Panel
A

8www.zippity-outdoor.com
OPTIONAL STEP 7: PURCHASE ROOF ACCESSORIES
OPTIONAL TABLETOP KIT FOR LIBERTY
LATTICE (ZP19053)
OPTIONAL WINTER COVER KIT
FOR LIBERTY LATTICE (ZP19054)
- Provides airow to allow for year round usage.
- Useful for holding small trays, plants, etc.
- Only to be used in winter months when
condenser is not running.
- Protects your condenser from winter elements.
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
@
These products can be found at www.zippity-outdoor.com.
Follow the instructions included with the optional accessory kits to assemble and install.