Zippity ROGER RABBIT VINYL GARDEN FENCE KIT 3 PACK User manual

1
www.zippity-outdoor.com
ASSEMBLY
INSTRUCTIONS
ROGER RABBIT VINYL GARDEN
FENCE KIT -3 PACK (22in H x 24in W)
30 MIN approximate assembly
time for 2 fence panels
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com

2www.zippity-outdoor.com
GENERAL INFORMATION
IMPORTANT
• Please read through before starting assembly.
• Important: Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
CALL US FIRST SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur.
If you discover any missing, damaged or defective parts, please contact our customer service department.
EMAIL: [e-mail]
PHONE: [phone]
Customer service agents are available to take calls weekdays from 8am-5pm EST.
To help you quickly and accurately, please have reference item number ZP19056 and the specic part name which can be
found on the next page. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so
please give us a call at 704-892-5222 / 877-234-6196.
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help resolve your issues rst. If you still decide to
return the product, you will need to intitate the return from the company you originally purchased from.

3
www.zippity-outdoor.com
STEP 1: LAY OUT MATERIALS
ROGER RABBIT VINYL GARDEN FENCE KIT (3 PACK)
TOOLS YOU WILL NEED
Cordless Drill
Tape Measure
A
D
F
B C
E
G
H
I
J
Post Caps (6)
Top Rails (3) -
1 ½” x 1 ½” x 24”
Bottom Rails (3) -
1 ½” x 1 ½” x 24”
Pickets (24) -
¼” x 1 ¼” x 21”
Posts (6) -
7
/ 8 ” x 1 ½” x 23 ¾”
Rail End Caps (12)
(6 are installed,
6 are loose)
Zippity Joiner Clip
Clip (6)
¾” Steel Screws (24)
(Bag A)
1” Steel Screws (12)
(Bag B)
Post Anchors (6) -
7
/ 8 ” x 1 ½” x 10 ½”

4www.zippity-outdoor.com
STEP 2: ASSEMBLE FENCE FRAME
STEP 2.1 Identify the top rail (D) and the bottom rail (E). Insert two rail end caps (B).
STEP 2.2 STEP 2.3
1. Position two posts (G) as shown.
2. Slide top rail over posts and align
predrilled holes.
3. Drive (4) ¾” steel screws (I) into the
pre-drilled holes.
1. Slide bottom rail over the posts until the
pre-drilled holes align.
2. Insert the post anchors (C) over the
bottom of the posts until they hit inside of the bottom rail.
3. Drive (4) ¾” screws into the predrilled holes in the bottom rail.
NOTE: Top rail can be identied by having
picket holes in both sides of the rail.
D
E
B
1
2
3
G
Tabs facing down
Align
I
1
23
NOTE: Ensure that the picket holes in the bottom
rail are facing towards the top rail.
E
Align
C

5
www.zippity-outdoor.com
STEP 3: INSERT THE PICKETS
STEP 4: ASSEMBLE ADDITIONAL PANELS
STEP 3.1
STEP 4.1
1. Rotate the fence frame so that the post tabs are facing up.
2. Insert (8) pickets (F) into the picket holes in the top and bottom rails.
Repeat Steps 1-3 to assemble the other two fence panels.
12
Tabs
F

6www.zippity-outdoor.com
3
x
x
2
1
STEP 5: INSTALL FENCE INTO GROUND
STEP 5.1 1. Move the fence to its nal location and mark the location of the posts.
2. Attempt to push fence into the ground.
STEP 5.2 Step 5.2-5.3 are only to be completed if ground is too hard for Step 5.1.
1. Loosen the top 6”of ground with claw hammer.
2. Add water to loose soil.
3. Use a block of wood to protect the post and lightly hammer the posts into the ground.
12
Push down on posts
w/ both hands.

7
www.zippity-outdoor.com
STEP 5.3 If ground is too hard, two 8” diameter 7”deep holes must be dug to accommodate two posts each as shown below.
STEP 5.4 Level the screen, backll excavated dirt, and tamp as necessary.
8 "
8 "
7 "

8www.zippity-outdoor.com
STEP 6: CONNECT PANELS
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
STEP 6.1 1. Straight Line Applications: Using Zippity joiner clips (H) and 1” screws (J) connect the panels as shown below.
2. Corner Applications: Using Zippity joiner clips (H) and 1”screws (J) connect the panels as shown below.
1
2
J
H
J
H