Zippity Madison Vinyl Picket Fence Kit 2-Pack User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 234 6196 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Caps (4)
2. Top Rail ( 2) - 1½” x 1½“ x 56 1/2”
3. Posts (4) - 7/8“ x 1½” x 39½”
4. Pickets (24) - 1 - ¼” x 1½” x 25 1/8“
2 - ¼” x 1½” x 22 7/8“
3 - ¼” x 1½” x 21 7/8“
5. Bottom Rail ( 2) - 1½“ x 1½” x 56 1/2“
6. Joiner Clips (4)
7. 3/4”Self-Auguring Stainless Steel Screw (24)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e.shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Madison Vinyl Picket Fence Kit 2-Pack
(30”H x 56 1/2”W)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 3.0/102216
1
3
2
4
5
Ground
This fence can easily be trimmed down horizontally
to fit your custom space. Use a fine toothed circular
saw or hack saw.
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
7
Not to Scale
6
2 1/2 in
40 in
14 1/8 in14 1/8 in
56 1/2 in
8 1/2 in
16 1/2 in
24 in
2 in
30 in
10 in 28 1/4 in

2
Position the two rails as illustrated and slide the two posts
thru the large routed holes in the top and bottom rails until
the predrilled holes in both rails are aligned with the pre-
drilled holes in both posts.
Note the difference between the top and bottom rails.
Tip!
Shine an LED light from smart phone or flashlight down the
end of the posts to help identify alignment of pre-drilled
holes if necessary.
Secure the rails to the post with screws on both sides of the
rails as illustrated.
1
2
STEP ONE
Madison Vinyl Picket Fence Instructions
1
Note: Align Holes
2
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
Note: Orientate the bottom of Posts as Illustrated
Note: Underside of Bottom Rail is blank
compared to the Top Rail with
holes for pickets on both sides.

STEP TWO
Pickets are identified 1, 2 and 3 to create scallop pattern. Please
insert in pattern as identified in illustration. Starting with the
tallest picket, slide each one down thru the top rail and into the
bottom rail.
Note: The tabs on the bottom of the pickets are intended to go
into the bottom rail to lock picket into place.
1
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
3Madison Vinyl Picket Fence Instructions
1
Note: Once inserted, the
pickets will lock into place.
To remove the picket(s),
gently insert a butter knife
along the picket direction
as shown and slowly pull up
the picket(s).

x
x
STEP THREE
4
1
Install fence into Ground
Move the fence to its final location and identify the location
of posts.
Attempt to push the unit into the ground as illustrated
Optionally:
2
2
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
x
x
1
1. If your ground is too hard, loosen the top 4” of the ground
with a claw hammer as illustrated.
2. Add water to loosen soil
3. Use a block of wood to the protect the top of post and
gently hammer each post into the ground equally.
Push down on the top of posts
with both hands
Option 1:
Option 3:
Option 2:
x
x
Block of Wood
x
x
Madison Vinyl Picket Fence Instructions

4
3
5
STEP THREE
3
Install fence into Ground - Continued
Level the assembled unit and backfill and compact dirt around
the base of each post to strengthen the unit.
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
4
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
4
Level
Madison Vinyl Picket Fence Instructions

12
Top Rail
Bottom
Rail
Top Rail
Bottom
Rail
12
45° Application
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
6
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: [phone] Fax: [phone]
www.zippity-outdoor.com
STEP FOUR
1
2
Fasten Joiner Clips
Fasten joiner clips by screwing into place on the top of the top
rail and top of the bottom rail as illustrated.
Screws are self-drilling.
Fasten the opposite end of the joiner clip as illustrated.