Zirkon zahn Face Hunter Installation instructions

Face Hunter
operator’s and maintenance manual

0202
Operator’s and maintenance manual (original operating manual)
Face Hunter
Version 22/10/2019
Copyright 2019
Zirkonzahn srl

0303

0404
Symbols used in this Operator’s and Maintenance Manual .............................. 08
Checklist of components and standard delivery ....................................... 09
Safetyandresidualrisks......................................................... 11
Manufacturer.............................................................. 11
General Information ........................................................ 11
Service................................................................... 12
Purpose .................................................................. 12
Intendeduse .......................................................... 12
Obligationsoftheuser .................................................. 12
Warranty................................................................. 13
Warranty claim ........................................................ 13
Lossofwarranty....................................................... 14
Technical improvements ................................................. 14
Safety regulations .......................................................... 14
Safetyconcept......................................................... 14
Personalsafetyequipment ............................................... 14
Safety measures when cleaning the device ................................... 15
Workplace, handling, references to safety ................................... 15
Troubleshooting ....................................................... 15
Restart protection after power failure ....................................... 15
Sourcesofdangerandrisks .................................................. 15
Possiblesourcesofdanger ............................................... 15
Residualrisks ......................................................... 16
Dangerofexplosion .................................................... 16
Transport, unpacking and setting up of the device ................................. 16
Safety procedures at the site of the installation................................ 16
Shippingcosts............................................................. 17
Components .................................................................. 19
Face Hunter............................................................... 20
Technical data ................................................................. 21
TABLE OF CONTENTS

0505
(WPEVKQPCNFGUETKRVKQPQHVJGGSWKROGPVCPFKFGPVKſECVKQPQHVJGEQORQPGPVU ....... 22
Device ID plate ........................................................ 22
Installation / First start-up........................................................ 23
Transport and unpacking..................................................... 23
Setting up and installation.................................................... 24
Important instructions for setting up the system............................... 24
Firststart-up .............................................................. 25
Operation..................................................................... 33
Training and practice ....................................................... 33
Installation and setting up .................................................... 33
Operation................................................................. 33
Shuttingdownthedevice.................................................... 34
Normal shutdown ...................................................... 34
Emergencyshutdown................................................... 34
Cleaning and maintenance ....................................................... 35
Safety measures when cleaning the device....................................... 35
Dry cleaning .............................................................. 35
Cleaning instructions ....................................................... 35
Maintenanceandcontrol..................................................... 36
Regularcontrols ....................................................... 36
Monthly.............................................................. 36
Bimonthly............................................................ 36
If required ............................................................ 36
Disconnect the device from power supply ................................... 36
Repairs and troubleshooting ...................................................... 37
Detected faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Replacement of electronic components ......................................... 37
Replacement of mechanical components ........................................ 37
Troubleshooting ........................................................... 38
Return................................................................... 38
Dismantling............................................................... 38
Disposal.................................................................. 38

0606

0707

0808
SYMBOLS USED IN THIS OPERATOR’S AND MAINTENANCE MANUAL
Caution: Source of danger!
Caution: Hazardous voltage!
Caution: Danger of explosion!
Prohibition: Access by unauthorised personnel is strictly forbidden!
Prohibition: Repair and maintenance work on moving parts is strictly forbidden!
Prohibition: The use of water, compressed air or solvents is strictly forbidden!
Mandatory sign: Unplug from mains power!
This symbol refers to the operating company’s binding legal rules or requirements.
This symbol refers to particularly important text passages in the Operator’s and
Maintenance Manual.
This symbol indicates the necessity to document work processes.

0909
CHECKLIST OF COMPONENTS AND STANDARD DELIVERY
Packing list - Equipment:
Face Hunter
(NCUJNKIJVEQPUKUVKPIQHOQWPVKPIYKVJƀCUJNKIJVU
Set Transfer Fork Face Hunter consisting of 5 bite forks and 10 reference markers
Transfer Fork Reference Cover
Mains plug
Lan cable
Dongle Face Hunter
75$ƀCUJFTKXG
$CVVGTKGUHQTƀCUJNKIJV
Operator’s and maintenance manual
Instructions for Face Hunter software
Face Hunter installation plan
If one of the components listed above is not contained in the supply, immediately contact your
Zirkonzahn partner.
Optional accessories:
Tripod
Laptop

1010

1111CHAPTER
SAFETY AND RESIDUAL RISKS
MANUFACTURER
Zirkonzahn srl, Headquarters Italy – 39030 Gais – BZ, is the manufacturer of the Face Hunter and
is referred throughout the Operator’s and Maintenance Manual as Zirkonzahn.
GENERAL INFORMATION
This Operator’s and Maintenance Manual is an integral part of the Face Hunter and must be
kept in a place known to the operator and easily and immediately accessible at all times. Only
adequately trained personnel must handle the Face Hunter.
This Operator’s and Maintenance Manual covers all you need to know for safe use and
maintenance of the Face Hunter produced by Zirkonzahn srl. However, it is not intended to replace
a training course with regard to the scope of application.
6JG(CEG*WPVGTKUCPKORQTVCPVEQORQPGPVQHVJGFKIKVCNYQTMƀQYCPFKVUHWPEVKQPUCTGKFGCNN[
suited for working with the Zirkonzahn CAD/CAM system. The operation of the Face Hunter is
very intuitive. However, in order to fully exploit its potential, which mainly consists in the further
use of the generated data in the Zirkonzahn.Software, it is recommended to take part in the CAD/
%#//KNNKPI(CEG*WPVGTKPVTQFWEVQT[EQWTUG;QWECPſPFCNNKPHQTOCVKQPCDQWVVJGEWTTGPV
course programme and a list of Zirkonzahn Education partners in your vicinity on our homepage
www.zirkonzahn.com or by contacting us directly by telephone under [phone].
Operational capability and long-term value of the Face Hunter can only be guaranteed if service
and maintenance work prescribed in this Operator’s and Maintenance Manual is carried out.
This manual is subject to amendments at Zirkonzahn's sole discretion in the event of technical
further development.
The device complies with the applicable EU directives. The declaration of conformity is available
and will be sent to the user upon request.
SAFETY AND
RESIDUAL RISKS

1212CHAPTER
SAFETY AND RESIDUAL RISKS
SERVICE
If any points of these instructions remain unclear to the customer or if indications,
instructions, safety instructions or technical explanations have not been fully understood,
FQPQVJGUKVCVGVQEQPVCEV<KTMQP\CJPŏUJGCFQHſEGRJQPGQTGOCKN
KPHQ"\KTMQP\CJPEQOQTVJGUGTXKEGEGPVGTUURGEKſGFKP[QWTOCKPVGPCPEGEQPVTCEV
PURPOSE
The intended use of the Face Hunter is outlined in this chapter.
In this connection a hazard analysis was carried out on the Face Hunter. The manufacturer does
not accept any responsibility for applications not described here which do not fall within the
FGſPKVKQPQHKPVGPFGFWUG6JGOCPWHCEVWTGTFGENKPGUCP[TGURQPUKDKNKV[HQTVJKU
Intended use
The Face Hunter is an optical scanner for capturing faces in 3-D and for taking 2-D images
on the basis of which the planned restoration is then positioned and modeled.
Obligations of the user
The operator must make sure to:
- Prevent abuse.
- Operate the system only with all intended safety devices closed and intact
(security switch, side covers etc.).
- Disconnect the Face Hunter from power supply by pulling the mains plug before
any intervention.

1313CHAPTER
SAFETY AND RESIDUAL RISKS
WARRANTY
In order to make use of the warranty service, exclusively original consumable materials, tools and
spare parts from Zirkonzahn should be used.
From the moment of delivery, Zirkonzahn grants a warranty of 12 months for the equipment.
If the Face Hunter is passed on to third parties, the warranty obligation is recognised only if the
passing on occurs within the set warranty period of 12 months.
Warranty claim
For warranty claims the customer must prove the date of purchase (i.e. copy of invoice).
The warranty covers the replacement of parts found faulty by Zirkonzahn
(material or production fault).

1414CHAPTER
SAFETY AND RESIDUAL RISKS
Loss of warranty
The loss of the warranty claim occurs in the following cases:
- Poor maintenance.
- Not proper, non-intended use.
-0QPEQORNKCPEGYKVJTGHGTGPEGUCPFRTGUETKRVKQPUURGEKſGFKPVJG1RGTCVQTŏUCPF
Maintenance Manual.
-/QFKſECVKQPUECTTKGFQWVD[VJGEWUVQOGTQTD[VJKTFRCTVKGUYJKEJJCXGPQVDGGPGZRNKEKVN[
authorised by Zirkonzahn.
- Use of tools, materials or spare parts which have not been produced or authorised by Zirkonzahn.
The warranty does not cover
- Damage during transport and supply (it is the forwarding company’s liability; only if noted on
the delivery note when receiving the goods!).
- Loss in sales and other economic consequences.
Technical improvements
Zirkonzahn is not obliged to carry out technical amendments to equipment produced at earlier
stages.
SAFETY REGULATIONS
Read and follow the safety instructions in this operator’s manual to avoid danger to persons and
FCOCIGVQRTQRGTV[;QWTUCHGV[EQOGUſTUV
Safety concept
The safety concept of the Face Hunter as well as this Operator’s and Maintenance Manual
were compiled according to the requirements of the Machinery Directive 98/37/EC in force
until 29 December 2009 and the Machinery Directive 2006/42/EC valid thereafter as well
as the European Low Voltage Directive (LVD) 2006/95/ EC.
Personal safety equipment
When working with the Face Hunter, no special safety equipment has to be used.
- Personal safety equipment required by law may vary from country to country.
- The user is committed to use the safety equipment in accordance with the national industrial
safety regulations.

1515CHAPTER
SAFETY AND RESIDUAL RISKS
Safety measures when cleaning the device
- Unplug from mains power!
Workplace, handling, references to safety
- Provide optimal work height.
- Do not expose the system to direct solar radiation.
- Equipment position for a good accessibility to operating elements.
-$CVVGTKGUHQTVJGƀCUJWPKVUOWUVDGKPVCEVCPFEQTTGEVN[KPUGTVGF
- Ventilation openings must be free.
Troubleshooting
1PN[KPUVTWEVGFSWCNKſGFRGTUQPPGNCTGCNNQYGFVQWPFGTVCMGVTQWDNGUJQQVKPI
+HCOCNHWPEVKQPECPPQVDGTGEVKſGFVJTQWIJVJGKPHQTOCVKQPRTQXKFGFKPVJG1RGTCVQTŏU
Manual, the Face Hunter must be turned off. Prevent unauthorised operation. For
troubleshooting please contact our
Zirkonzahn Support: Tel. [phone], [email protected]
Restart protection after power failure
In the event of malfunction of the system during a phase of work (e.g. power failure) the
device as well as the software Zirkonzahn.Scan must be restarted.
SOURCES OF DANGER AND RISKS
Possible sources of danger
According to the safety technical hazard analysis 09/02/2009, Machinery Directive 2006/42/EC;
98/37/EC; Low voltage Directive (LVD) 2006/95/EC:
- Components under electrical voltage
- Cleaning with solvents
-+PUWHſEKGPVDGCTKPIECRCEKV[QHVJGKPUVCNNCVKQPUWTHCEGHQTVJGGSWKROGPV
- Heat generation at the ventilation opening

1616CHAPTER
SAFETY AND RESIDUAL RISKS
Residual risks
- In the event of equipment defects push the EMERGENCY SHUTDOWN switch and follow
hazard warnings.
- Avoid residual risks by increased attentiveness.
- Pay attention to risks at the installation site.
- Defective power supply lines.
- Fire hazard if the device is operated unattended.
- Danger of burns at the ventilation opening, do not touch neither during operation nor
immediately afterwards.
- Eye damage: Do not look into the lens from immediate proximity.
- Electromagnetic waves: Do not use near people with pacemakers.
Danger of explosion
It is strictly forbidden to use the device in explosive atmospheres and to clean the
Face Hunter with solvents.
TRANSPORT, UNPACKING AND SETTING UP OF THE DEVICE
- The Face Hunter has to be moved and put down on surfaces with suitable stability, in a dry
place and in a non-corrosive environment.
- Stable, non-slip installation surface, which can bear a minimum weight of 10 kg.
- Caution when removing the cardboard casing (glass cladding).
- Pay attention to danger of injury when unpacking and setting up the scanner.
- The Face Hunter must not be connected to the electric circuit during the installation
phase: Danger of electric shock.
- The original packaging has to be kept for at least 1 year.
Safety procedures at the site of the installation
-5VCDNGƀCVCPFFT[KPUVCNNCVKQPUWTHCEGUHQTVJGGSWKROGPV
- Safety distance of min. 2 m to combustible material.
- Safety distance of min. 2 m to water.

1717CHAPTER
SAFETY AND RESIDUAL RISKS
SHIPPING COSTS
Unless otherwise agreed in writing, the buyer is responsible for dispatch, freight and possible
import fees.
Check the delivery for completeness and integrity immediately after receipt.
Evident defects must be noted on the delivery documents, in order to claim for compensation
against the transport company.
In case of complaints, have the transport documents countersigned by the carrier and send a copy
to Zirkonzahn.

1818CHAPTER
SAFETY AND RESIDUAL RISKS

1919CHAPTER 2
COMPONENTS
COMPONENTS

1 x
1 x
1 x 1 x
1 x 1 x
1 x
1 x
1 x 1 x 1 x 1 x
Optional
2020CHAPTER 2
COMPONENTS
FACE HUNTER