Zodiac Pool Systems andy AquaPure EI Series User manual
H0331400 Rev A
Installation and
Operation Manual
Chlorine Generating Device
Dual Voltage 240V/120V
APURE35
FOR YOUR SAFETY - This product must be installed and serviced by professionals who are
can create an unwanted electrical hazard which can cause serious injury, property damage, or
This manual contains important information about the installation, operation and safe use of
WARNING
AquaPure Series
Page 2
Page 3
Table of Contents
5
8
...................................... 8
.............................................. 9
10
........................................... 10
................................. 10
................... 11
.......... 13
................................................... 13
................................. 14
................................................14
...........................................14
..............................16
........................... 17
................................ 17
18
......................... 18
............................ 18
........................................ 18
........................... 18
..................... 19
.............................................. 20
........................... 20
.......................................20
...........................20
..............................21
......................21
23
.................................................... 23
............ 23
................... 23
..................... 23
................................................. 24
............................................... 24
................................................. 24
25
.................................................................. 25
............................................................. 25
.............................................. 26
........................................................ 27
................................27
28
....................... 28
Exploded Views 31
........................................................... 31
................................................ 32
Page 4
List of Figures List of Tables
............................... 21
..... 22
.......................... 8
.................................... 9
...................... 10
...................... 11
..................... 11
.................................. 11
......................................... 11
............................. 11
Figure 9. Pipe Spacer ........................................... 11
........................... 12
................................ 12
......................................... 12
......................... 12
......................................... 12
................................ 12
.......................... 12
......................... 12
... 13
............................................ 15
........................ 15
........... 16
............. 17
........ 17
......... 23
................................ 26
.................................... 26
........................................ 26
...................... 27
............................... 32
................................ 27
.................................. 32
.................. 32
Page 5
READ AND FOLLOW ALL INSTRUCTIONS
All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes.
When installing and using this electrical equipment, basic safety precautions should always be followed, including the
following:
WARNING
EQUIPMENT UNDER PRESSURE:
WARNING
WARNING
WARNING
RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH
Page 6
WARNING
To Reduce the Risk of Injury -
WARNING
WARNING
WARNING
WARNING
PREVENT CHILD DROWNING:
WARNING
WARNING
Page 7
SAVE THESE INSTRUCTIONS
WARNING
CAUTION
ALWAYS ADD ACID TO WATER
CAUTION
Page 8
Maximum Operating Pressure: Input Current @ 240 VAC: ~1 A
Input Current @ 120 VAC: ~1.3 A
Minimum Flow Rate:
Maximum Flow Rate: Input Freq:
Required Salt Level: Output Voltage:
Maximum water volume treated:
APURE35
Output Current (adjustable by switch):
APURE35 -
Chlorine Output:
APURE35 -
Dimensions:
Power Pack (L x W x H):
Electrolytic Cell (L x W x H)
Input Voltages:
Weight:
Power Pack:
Electrolytic Cell:
The cell must be installed as the
last piece of equipment in the
circulation plumbing system just
before the pool
Cell
Heater
Pump
To common
power source
Power Pack
Filter
Pool Intake Spa Intake
Spa ReturnPool Return
Page 9
ITEM DESCRIPTION QTY
A Power Pack 1
B Cell 1
C Power Pack Bracket 1
D 1
E Screw Set (includes wall plugs) 1
F Installation and Operation Manual 1
G Hole Saw 1
H Locking Ring Tool 1
I Winterizing Cap 1
H033140000_BETA-
Installation and
Operation Manual
Chlorine Generating Device
Dual Voltage 240V/120V
APURE25
APURE35
FOR YOUR SAFETY - This product must be installed and serviced by professionals who are
quali ed in pool/spa product installation and service. Improper installation and/or operation
can create an un wanted electrical hazard which can cause serious injury, property damage, or
death. Improper installation and/or operation will void the warranty.
This manual contains important information about the installation, operation and safe use of
this product. This information should be given to the owner/operator of this equipment.
WARN ING
AquaPure Series
A
B
C
E
H
I
D
G
F
Page 10
Before you begin your installation, please check that you have the right tools and a suitable location to install the
power pack and cell. Please ensure that you have read and understood the Important Safety Instructions section.
Installation Materials Furnished Tools Needed for Installation
WARNING
EQUIPMENT UNDER PRESSURE:
WARNING
Cell
Power
Pack
1
WARNING
FOR YOUR SAFETY:
The installation requirements for the Jandy AquaPure Ei chlorine
generating device are as follows:
The power pack must be be installed at least 5 ft. (1.5 m) vertically off
the ground.
the power pack must be be installed at least 5 ft. (1.5 m) from
the inside wall of your swimming pool or spa; in Canada, the power
pack must be be installed at least 10 ft. (3 m) from the inside wall of your
swimming pool or spa.
equipment in the circulation plumbing system just before the pool (see
Figure 3).
from the power
pack (see Figure 3).
Page 11
7. Invert the lower clamp and place on the pipe. Mark the pipe for drilling the feeder holes (see Figure 7).
8. Drill the feeder holes using the holesaw provided. Ensure holes are clean and smooth (see Figure 8).
NOTE:
Requirements
Drilling Feeder Holes
Screws
Thru-holes
Feeder Holes
Lower
Clamp
Upper
Clamp Push-button
Spacer used for 1 ½ in
(40mm) pipe only
1. Ensure placement of the cell and the power pack will meet all the installation requirements outlined in Section 3.2.
3. Position the power pack in place by aligning the bracket with the corresponding thru-holes (see Figure 5).
WARNING
Page 12
Alignment
10. Verify the gasket is attached to the upper clamp. The curved side of the gasket must be pointing down so that it
will create a seal with the pipe.
the clamp are snapped into place.
12.
Insert the o-ring into the channel on the clamp
and then attach the cell (see Figure 11 and 12).
13. Position the locking ring in proper alignment, making sure the bump aligns with the top thread (see Figure 13).
NOTE: .
Red
Red
Blue
Black
Locking Ring
Tool
Water Flow
O-Ring
Inlet Outlet
The groove
must be on
the inlet side
Align the bump with
the high thread on
the lower clamp.
NOTE: The Upper
Clamp is not shown
in this diagram but it
should be installed.
Page 13
1. Wire power pack to pool pump power source using #12 AWG (3.0 mm2) insulated wire and conduit. The power
pack should be connected to the pump motor switch or automatic timer (pool pump timer) as shown in Figure 18.
2. Attach the third wire (ground) from the electrical panel to the ground point inside the power pack. Additionally,
applicable local and/or National installation codes may require the equipment to properly bonded to other pool
equipment or to a bonding grid. Earth bonding per Section 3.5 must also be accomplished to ensure personal
safety and safety of equipment.
The National Electric Code (NEC) requires pool equipment to be bonded to each other. Check your local codes to
determine if the NEC and/or other local installation codes are enforced by the Authority Having Jurisdiction (AHJ).
A solid, copper # 8 AWG (8.37 mm2) wire is recommended, per the NEC, for bonding the power pack to a permanent
grounding wire gauge. Attach the bonding point located on the bottom of the chassis backplate to a common earth
bonding point. Do not use the power pack as the common bonding point. Each piece of non-related pool equipment
requiring a ground should also be bonded to the common, approved earth bonding point. Never ground a pool pump
to the chassis backplate. In Canada, the Canadian Electrical Code (CEC) dictates that the bonding conductor be,
2
).
WARNING
Before
Use Copper Conductors Only – Rated for 90°C Minimum
RIBBON CABLE
FROM CONTROL PCB
Power PCB*
Factory Wired for
240 VAC or 120 VAC ~
*The Power PCB auto-detects voltage
Pool Pump
TO EARTH
BONDING POINT
POOL PUMP TIMER
3
12
6
9
240 VAC or
120 VAC
CIRCUIT BREAKER
PANEL
50/60 Hz
3 wire
Line 1
ACT
Pump
Line 2
NEUTRAL
0V
B
A
0V
POS
BLUE
RED
RED
BLK
BLK
TO EI CELL
GROUND
LINE 1
LINE 2
RED
BLK
BLUE
TO FAN
OPTIONAL
CONNECTION
TO AQUALINK® RS
OR PDA
BLK
YLW
RED
GRN
RED
BLK
BLK
NOT USED
LOAD 2
LOAD 1
GROUND (CHASSIS)
WHT
TO EARTH
BONDING POINT
NOT USED
NOT USED
NOT USED
Page 14
WARNING
FOR YOUR SAFETY:
Before
NOTE
NOTE:
To set the controller type:
2. Wait for the start-up sequence to complete.
will be displayed on the screen.
the screen for two (2) seconds.
1. Ensure that all power to the power pack and the controller is disconnected/turned off at the circuit breaker.
(see Figure 19).
NOTE:
Page 15
being used.
5. Attach a cable tie to the controller cable as shown (see Figure 19).
Cable Tie
Comm Hole
directly
relay
(see Figure 20).
AquaLink RS or PDA Power Center
Filter Pump Relay Aux.3Relay
Load1
Line 1
120 VAC
To Filter Pump
(120 VAC)
To Power Pack
(120 VAC)
Neutral
To Breaker
Panel
Filter Pump Relay Aux.3Relay
Load 2
Line 2
Load 1
Line 1
240 VAC
To Filter Pump
(240 VAC)
To Power Pack
(240 VAC)
To Breaker
Panel
Page 16
connection:
2. Wait about 20 seconds. If the connection was successful, a symbol will appear in the top right corner of the
power pack display.
NOTE:
Jandy
Power Center
Power Pack
OPTIONAL
4321
RED
BLK
YEL
GRN
Red, 4-Pin
Terminal Bar
RED
GRN
YLW
BLK
B
A
0V
POS
RED
BLK
appropriate screw terminals on the circuit board and wire the power pack
terminal bar (see Figure 21).
NOTE
Page 17
handle of the valve until the red “No Flow” light has turned off and all large air bubbles are cleared from the cell.
Do not install
past 45 degrees
angle that the cell will be leaning to ensure that you drill in the right position.
The cell must be installed as the last piece of
equipment in the circulation plumbing system
just before the pool
Cell
Heater
Pump
Power Pack
Filter
Pool Intake Spa Intake
Spa ReturnPool Return
To common
power source
Control Valve Installation Options
Water Flow
Page 18
Rectangular Pools
Circular Pools
Oval Pools
Sloping Sides
Rectangular Pools
Circular Pools
Oval Pools
Sloping Sides
APURE35
Chlorine Production
Residential Pools
General Rule of Sizing:
Year Round Use:
professional.
High Water Temperatures: Because chlorine demand increases with the rise of water temperature, adjustments
must be made in order to keep up with chlorine demand. In hot summer months, where the water temperature
rises above 85ºF, you must increase the pump run time and increase the percentage (%).
Chlorine Stabilizer
Nitrates
Make sure nitrates are not present in your pool.
Page 19
Metals (some metals) can cause loss of chlorine and stain your pool. Have your local pool professional check for
metals and recommend methods of removal.
Chloramines should not be present in pool water. When organic materials combine with free chlorine,
chloramines are formed. This ties up the free chlorine in your pool and does not allow the chlorine in your pool
to disinfect. Chloramines also cloud pool water and burn the eyes. Shock to remove chloramines at the initial
startup of the pool.
Super Chlorination burns out the organic material that has combined with chlorine which frees the chlorine for
set the chlorine production to
Shocking
This method involves the manual addition of chemicals to quickly raise the level of chlorine. When the chlorine
level is quickly raised to 5 - 15 ppm the pool water is said to have been shocked.
NOTE
CAUTION
pH condition resulting from the operation of a salt water chlorination system is close to neutral. However,
other factors usually cause the pH of the pool water to rise. Therefore, the pH in a pool chlorinated by a salt water
if other factors such as high calcium hardness or total alkalinity are the cause and then balance accordingly.
Total Dissolved Solids (TDS). Adding salt to pool water will raise the TDS level. While this does not adversely
affect the pool water chemistry or clarity, the pool water professional testing for TDS must be made aware salt has
to arrive at the correct TDS level.
New pool water
and properly balanced before turning on the chlorinator system.
Sequestering Agents can be used to compensate for source water which may have unusually high calcium
hardness. High calcium hardness can contribute to scale formation in the pool. Sequestering agents will help
keep minerals in solution and under some conditions can prevent scaling from happening. Consult your pool
professional about the use of a sequestering agent.
In accordance with Association of Pool and Spa Professionals (APSP) standards, we recommend the following water
the pleasing appearance of the water. The Jandy AquaPure Ei is warranted to operate properly only if the following
conditions are met:
Free Chlorine
corrosion of pool metals.
Combined Chlorine (Chloramines) None (Super chlorinate to remove all chloramines).
pH
Chlorine Stabilizer (Cyanuric Acid) 30 - 50 ppm (For outdoor pools only).
Total Alkalinity 80 - 120 ppm
Calcium Hardness
Metals (Iron, Manganese) None
Nitrates None
Phosphates None
Page 20
taken from two (2) places, described below. Compare the two (2) samples. A higher level should be found at the pool
return line. The higher level at the pool return line indicates the salt water chlorinator system is producing chlorine.
1. At the pool return line.
Add salt to the pool if the salt is too low (see Table 1) or if salt indicator light turns on. For a new pool or newly
resurfaced pool it is recommended to wait at least 30 days (surface should be completely cured) before adding salt.
added at start up.
dissolve.
Do not
Do not
CAUTION
This manual suits for next models
1
Table of contents
Other Zodiac Pool Systems Swimming Pool Filter manuals
Zodiac Pool Systems
Zodiac Pool Systems JANDY TRUCLEAR XL User manual
Zodiac Pool Systems
Zodiac Pool Systems TruClear Jandy Pro Series User manual
Zodiac Pool Systems
Zodiac Pool Systems Nature2 Fusion soft User manual
Zodiac Pool Systems
Zodiac Pool Systems PG User manual
Zodiac Pool Systems
Zodiac Pool Systems Aquapure Ei APURE35PLGC User manual
Zodiac Pool Systems
Zodiac Pool Systems Jandy JS100-SM Manual
Zodiac Pool Systems
Zodiac Pool Systems Ei Series User manual
Popular Swimming Pool Filter manuals by other brands
Peraqua
Peraqua OCEAN Skimmer deluxe Operation manual
Pool Pro
Pool Pro Neptune NDC25 troubleshooting guide
Pool Systems
Pool Systems G2flo ZEN quick start guide
Evolution
Evolution Rage Twin instruction manual
hurlcon
hurlcon Filtrite CE25 Installation and operating instructions
Clear Water
Clear Water MineralPURE RC-50 user manual
Aqua Medic
Aqua Medic aCone 1.5 EVO Operation manual
Waterco
Waterco 20 SC owner's manual
Pentair Pool Products
Pentair Pool Products SMBW 4000 Series operating manual
Oasis Aquatics
Oasis Aquatics Oasis SE Series Installation and operation manual
Polaris
Polaris AutoClearPLUS Installation and maintenance guide
T.I.P.
T.I.P. HNB 1600 manual
Hayward
Hayward SP1094D owner's manual
BSV
BSV N-BSSALT user manual
Sterilor
Sterilor XP Connect Installation and user manual
VSV
VSV Aquatic U Installation and user guide
CTX PROFESSIONAL
CTX PROFESSIONAL E Series Installation and operating instructions
Idegis
Idegis DOMOTIC SERIES Hardware installation and maintenance manual