Zoom Single Owner's manual

ZOOM Single Desk
Assembly & User Instructions
ZOOM

Standing
just 15 min per hour
provides great
health benefits

Contents
ZOOM Single
Use/Liability 3
Parts List/Tools 4
Assembly 5-8
Trouble Shooting 8
Specications   9

Use / Liability
This height adjustable desk has electric motors and is designed for use in dry work areas only.
The desk height is adjustable so that it can be positioned at the most ergonomically suitable
height.
Any other use is at users risk.
Under no circumstances does the manufacturer accept warranty claims or liability claims for
damages caused from improper use or handling of the desk frame.
Please be informed that the anti collision software is designed for furniture protection, not
human protection.
Assembly
3 4
Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to
accommodate the change in height.
Keep children away from electric height-adjustable desks, control
units and handsets. There is a risk of injury and electric shock.
Keep all electrical components away from liquids.
Do not sit or stand on the desk frame.
Do not crawl or lie under the desk frame.
Do not place any objects taller than 20” underneath the desk.
Do not open any of the components - the Legs, Control Box, or Switch.
There is a danger of electric shock.
This product is designed with a duty cycle of 10%
(2 min. on, 18 min. off).
In the event of a power outage or if the power cord is unplugged, a
manual reset may be necessary - see USE section.
IMPORTANT: You must RESET the desk prior to use.
WARNING
Pinch Point
Keep hands and
ngers clear.

4
Tools
Parts List
4mm Allen Wrench (included) Phillips Head Screwdriver
and/or Power Drill Tape Measure
Parts List
Part Qty
Leg 2
Foot 2
Frame End-CB 1
Frame End 1
Centre Rail 1
Part Qty
Side Bracket 2
Control Box 1
Handset 1
Power Cord 1
Cable 1
Part Qty
M6x14 Machine Screw 12
M6x10 Machine Screw 16
M5x20 Wood Screw 11
M5x16 Wood Screw 2
Cable Chip 10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15
8
9
7
1
2
45
3
12
12
12
12
6
6
11
11
12
13
13
13
11 10

Lay out all components and hardware to ensure that you have all items listed on the
parts page. Slide the Control Box (part 7) off the Frame End-CB (part 3) and set aside.
Fully separate Frame End (part 4) from Frame End-CB (part 3). You will nd the Centre
Rail (part 5) inside.
Place one of the Legs (part l) into the Frame End-CB (part 3)
ensuring that the bar (arrow) is on “top” in relation to the Leg
(part l).
Line up the holes on the Leg (part l) with the holes
on the Frame End-CB (part 3).
Using the supplied Allen Wrench, insert four (4) M6x10 Machine
Screws (part 12) through the holes in the Frame End-CB (part 3),
going into the Leg (part l) and rotate each screw just a few turns.
After all four (4) M6x10 Machine Screws (part 12) are inserted,
tighten all four (4) screws.
Do the same for the other Leg (part l) and the Frame End (part 4).
The Frame End-CB (part 3) should be placed on the
side of the desk where you plan to mount the Control
Box (part 7) and the Handset (part 8).
Slide the Side Bracket (part 6) into the Frame End-CB
(part 3). Insert two (2) M6x14 Machine Screws (part 11)
through the two (2) holes in the bottom of the Frame
End (part 3} going into the inserted Side Bracket (part
6). Using the supplied Allen Wrench, rotate each screw
just a few turns. After both M6x14 Machine Screws are
inserted, tighten both screws.
Do the same for the other frame end/leg assembly.
Assembly
1
2
3
5 6
1
12
3
1
11
3
6
3 4
7
5

6
Slide the two (2) Centre Rails (part
5) into the two Frame Ends (parts
3 & 4) ensuring: a} the slots in the
Centre Rail (part 5) face inward b}
the slots in the Centre Rail (part 5)
are closer to the top edge when
the assembly is upside down (see
inset).
For each leg assembly, attach a Foot (part 2) with four (4)
M6x14 Machine Screws (part l 1) and tighten in a cross-
pattern.
Check both sides of the desktop before placing the
desk base on the underside of the desktop.
Adjust the width of the desk base to t the desktop
by sliding the two halves outward. We recommend
leaving at least 1/2” of the desktop width (on each
end) protruding beyond the frame width and centring
the side brackets (part 6) before and after.
Lock the position of the Centre Rail (part 5)
using eight (8) M6x10 Machine Scews (part 12).
Ensure the M6x10 Machine Screws (part 12)
contacts the Centre Rail (part 5) by sliding the
Centre Rail (part 5) as needed.
Assembly
4
5
6
7
5
3 4
11
2
3
4
5
10
10
12

Double check that the wood screws are not
too long for your desktop and won’t puncture
the surface when screwed all the way in.
We recommend that you pre-drill any holes
needed for fasteners. Never use countersunk
screws.
Double check that the desk base is properly
positioned on the underside of the desktop.
Attach the desk base to the underside of the
desktop using eleven (11) M5x20 Wood Screws
(part 13).
Attach the Handset (part 8) so the front of the handset is ush with the front desktop
edge (or recessed up to 1/8”). The handset may be placed anywhere along the
front edge of the desktop, but we recommend placing it towards an end so it
prevents interference when seated. Use two (2) M5x16 Wood Screws (part 14) to
attach the handset to the desktop.
Do not overtighten screws in this step. Overtightening could cause damage to the
components.
Slide the Control Box (part 7) onto the Frame
End-CB (part 3).
Connect the cable exiting the Leg (Part 1)
that is attached to the Frame End-CB (part 3)
directly into the Control Box (part 7).
Connect the Cable (part 10) to the other Leg
(part 1) and to the Control Box (part 7).
Connect the Handset (part 8) cable to the
Control Box (part 7).
Connect the Power Cord (part 9) to the
Control Box (part 7).
Use the adhesive-backed Cable Clips (part 15) to secure the cables so they do not
sag.
Assembly
8
9
7 8
8
13
14
3
8
7
10

8
Turn the assembled desk right-side up. With at least two people, grab the DESK BASE
(not the desktop) and turn the desk right-side up. Adjust the pre-installed glides on
the Feet (part 2) as needed.
Plug the Power Cord (part 9) into a 230v outlet.
Assembly
10
11
12 RESET PROCEDURE
Press and hold the DOWN button on the Handset (part 8) until the desk reaches its
lowest height.
Release the DOWN button.
Press and hold the DOWN button again for about 10 seconds.
Release the DOWN button.
Press and hold the DOWN button again until the desk lowers a little bit more, slightly
rises and stops.
Release the DOWN button.
Your desk is now ready to use.
The desk base can be adjusted by pressing and holding either the UP or DOWN
button until the desired height is reached.
Ensure there are no obstacles in the desk’s path, and that the desktop
is not touching any walls. Please also ensure that all cords are an
appropriate length to accommodate the change in height.
IMPORTANT: You must RESET the desk prior to use.

9 10
Height Range 685 - 1185 mm (without desktop)
Base Width 1200 - 1800 mm
Travel Speed 40 mm per second (no load)
Distributed Load 125Kg
Duty Cycle After 2 min. continuous use rest for
18 min to prevent overheating
Soft start/stop
Adjustable leveling studs
Trouble Shooting
Specifications