Z-WAVE CONTROL
4. You will see 7 or 8 new on/off devices in your app: 5 channels for on/off
control, 2 channels for on/off monitoring (USB ports reporting charging/
charged status, no control), and possibly one master node to access and
adjust advanced settings in, depending on the hub you’re using.
2. ADD DEVICE to your hub
CLICK CH1 BUTTON 3 TIMES QUICKLY
3. Finalize inclusion at the strip.
1. Plug the Power Strip into a grounded receptacle you’re planning to
use it at (it doesn’t need to be close to the hub)
Initiate inclusion (pairing) in the app (or web interface).
Not sure how? Get step-by-step instructions for adding
the strip to SmartThings, Vera, Hubitat and other hubs
here: www.support.getzooz.com
2.1 A Max
CH 1 CH 2 CH 3 CH 4 CH 5
All LED indicators will start flashing.
NEED SOME HELP?
ask@getzooz.com
1. Bring the strip within direct range of your Z-Wave gateway (hub).
2. Put the Z-Wave hub into exclusion mode (not sure how to do that?
ask@getzooz.com).
3. Press and release the CH1 button 3 times quickly.
4. Your hub will confirm exclusion and all of the channels (child outlets)
and the main device will disappear from your controller's device list.
EXCLUSION (REMOVING / UNPAIRING DEVICE)
FACTORY RESET
TROUBLESHOOTING
The Power Strip won’t add to your system? Try this:
1. Initiate EXCLUSION and click the CH1 button 3 times quickly.
2. Click the CH1 button 4-5 times quickly when adding it.
3. Bring the Power Strip closer to your hub, it may be out of range.
4. Double-check if the device is powered.
5. Get troubleshooting tips for your hub at www.support.getzooz.com
If your primary controller is missing or inoperable, you may need to reset
the device to factory settings. To complete the reset process manually,
click-click-click’n’hold CH1 button for at least 10 seconds. All LED
indicators will flash to confirm successful reset.
NOTE: All previously recorded activity EXCEPT and custom settings
for the kWh record will be erased from the device’s memory.
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE
INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHE-THER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR
ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE
PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF
AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR
REPAYMENT OF THE PURCHASE PRICE FOR THAT POR-TION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES
ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF
PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S
DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE
THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN
WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may try to correct the
interference by taking one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from receiver
- Consult the dealer or an experienced radio/TV technician for additional assistance
All brand names displayed are trademarks of their respective holders.
© Zooz 2022
KWH RESET
If you’d like to reset the kWh record for any of the outlets, just click the CH
button next to the respective outlet 10 times very quickly. Network
exclusion or factory reset will NOT automatically erase the kWh data.
ADVANCED SETTINGS
Please refer to your controller's user guide for advanced programming
instructions as they are a little different for every soware.
Not sure where to start? Go to www.support.getzooz.com for detailed
instructions how to change the settings on SmartThings, Vera, and
more. Or just email us: ask@getzooz.com
ASSOCIATION
The Power Strip supports Group 1 for lifeline communication of on/off
status to the Z-Wave gateway controller (hub).
CUSTOMIZE YOUR POWER STRIP
You can adjust the frequency and threshold for
power monitoring or change how the buttons
and LED indicators behave on your Power Strip.
Scan the QR code for a full list of parameters for
this device and learn how to access them on
your hub.
