ZOSI ET-1026 User manual

PROFESSIONAL SECURITY MADE EASY
Quick Start Guide
For more information of your new system, please refer to www.zositech.com

1
Statement
Thank you for purchasing this product. ZOSI is committed to providing its customers with a high quality, reliable security
solution. ZOSI cannot assume responsibility for any consequences resulting from the use thereof.
Before Installation
This product may require cabling. It is strongly recommended that all products and components be tested prior to
installation.
Applications
By adding a 2.5” SATA hard drive to the NVR, you can record&playback recordings from the cameras.
By connecting the NVR to the Internet, you can view the cameras anywhere anytime.
Tips
These instructions are to assist your installation of the system and remote surveillance.For more instructions and details,
please contact us.
Tech Support
For products introduction& specifications, please visit www.zositech.com.
For FAQ and troubleshooting, please visit ZOSI Help center https://support.zositech.com
If you need customer support, email us and we will respond within 24 hours :ser[email protected]
1. Connect Your System
Router
Mouse & USB Interface
Power Port
Power Port
3
1
2
5
4
6
1. Connect your system
Install the antennas for cameras.
Power the cameras with power supplies (12V 1A)
Connect the NVR to Router with an Ethernet cable .
Plug the mouse (included) into the USB port at the rear panel of the NVR. (USB port can be used to backup videos by
USB flash disk.)
Power the NVR with its power supply (12V 3A)
Switch on the NVR through the power button on NVR.
Connect the monitor to the NVR with HDMI.(Optional)
1
2
3
4
5
6
7
Within seconds, there will be a camera live image shown on the screen.
Username: admin
Password: None (The password is initially blank, just click login)
Tips:
To protect your privacy, please right click the mouse > Go to System Setup > System Admin > User > Set password to
change your password.
7

2
2. Camera Mounting Spots
3. Adjust the Camera
4. Wired connection
Adjust the camera to the position you want .
The neck of the stand attached to the mounting base, rotate the stand
by loosening the radial joint locking ring. Once in position ,tighten the
ring again.
Tips:
1. If you want the camera to work wirelessly, use Match Code to add camera to NVR. See the Point 5 about Add camera by
match code.
2. If you want the camera to work wired, use Auto Add. This requires you hard wire the cameras to router to get it work.
If camera mounting spot is out of WiFi range, you need to connect cameras to NVR with wired cable to get image.
1
2
The neck of the stand attached to the mounting base, rotate the stand
by loosening the radial joint locking ring. Once in position ,tighten the
If camera mounting spot is out of WiFi range, you need to connect cameras to NVR with wired cable to get image.
1
2
2.1 Mount the cameras anywhere within the Wi-Fi range, plug the power adapters to the camera (Smaller one is for camera).
2.2 The cameras should start to stream videos to NVR within 1 minute.
2.3 If it does not display video,maybe caused by too many obstacles or too long distance to connect NVR's WIFI . Please try
to move the cameras closer to the NVR.
4.1 Use standard Network cables to connect the cameras to the Router
4.2 After connecting the camera to the router,please right click the mouse > go to “Video Manage” > click “Refresh” > click “Auto
Add” .The camera will be added to NVR,and the screen will display video.
Router
Network cables Network cables
Camera
NVR
Step 1: Connect the NVR to the Internet
Connect the NVR’s WAN port to LAN port of your router with an Ethernet cable. When the NVR is connected to the Internet,
within minutes you shall see the Cloud ID and status shows "ONLINE" on the right bottom corner on your screen.
Network Video Recorder
Network Video Recorder
Network Video Recorder
Network Video Recorder
Cloud ID:662023312 ONLINE
2. View on Smartphone
Tips:
If the status does not show“ONLINE”, please go to System Setup > Network Setup> enable the DHCP or manually allocate
IP for the NVR. If the setting still doesn't work, please ask your network administrator for help. (Ex.: port 80 need to be
opened on the router.)

3
Step 2: Download the App
Search "IP PRO" or "EseeCloud" in App store or Google Play. Or Scan the QR Code to download the App.
IP Pro App store Google play
Step 3: Run the App
A: Install the free App.
B: Tap Register and input your User name, Password,Email to create a new account.
C: Login the App, Tap “+” icon on the right upper corner of the screen > Add device by ID.
D:Configure the following
1
2
3
4
5

4
Network Video Recorder
Cloud ID:662023312 ONLINE
1. Cloud ID: The Cloud ID can be found at right bottom corner of the screen.
Or right click the mouse > go to System Setup > Network Setup > Scan the QR code.
2. Descriptions: Use a name as you like for your system
3. User Name: Enter the NVR’s User Name (Default: admin)
4. Password: Enter the NVR’s Password (Default: No password required, just leave it blank)
5. Tap Submit.
E: Tap the channel Number,then you shall see the live view of those cameras corresponding with the specific
channels.

5
Step 1: Download EseeCloud.exe from CD and install it on your computer.Or go to https://support.zositech.com to
download the PC Client Software – EseeCloud.exe
Step2.1: Add device by Cloud ID
Go to Device management . Choose add device by Cloud ID.
Cloud ID : same as Cloud ID
Username: Enter the NVR’s User Name (default: admin)
Password: Enter the NVR’s Password (default: No password required, just leave it blank)
Note: same as the IP Pro/EseeCloud account Descriptions in smartphone
Channels: same as your NVR channel number
3. View on PC Client Software
After opening the EseeCloud software, User login interface will be popped up.Enter username, password and then click
“Login” to enter the EseelCoud operational interface. You could enable “Remember password” so that you don’t need to input
password when you want to PC client in next time.
Attention:
The current version of IP Pro/EseeCloud only can use “admin” as username, and the default password is blank. For security
reasons, please be sure to modify your login password in the first login, in order to prevent unauthorized party access to your
device or cause other undesirable consequences.

6
Step2.2: Add device in local network
Step2.3: Image Preview
2.2.1 Please click the refresh button which is located at right side of the ”Device in same lan”, then all the available devices
within the LAN will be listed out.
2.2.2 Please click the “Add ” button to add the device. And the added device will be shown up at the device list which is
located at the right side. If you didn’t change the device’s description, the added device will be shown up in the form of IP
address.
After adding the device successfully, click Live View to enter into the preview interface > choose an arbitrary device in the list
> click the icon you could connect all the channels under the device > click the icon in channel detail icon.The icon
means start or stop video as below:

7
4.View on PC via IE
1. When your PC is located on the same LAN as the NVR (normally means they are connected to the same router).
Step1. Find the IP address and Web port of your NVR (IP address can be found in System Setup > Network Setup).
Step2. Enter the NVR’s IP address in your IE browser in format http://youripaddress, for example: http://192.1.1.100 (If
the default web port 80 has been changed e.g. to 100, you will need to add the new port number when you input the
IP address in the browser, for example: http://192.168.1.100:100).
User Name: Enter the NVR’s User Name (default: admin)
Password: Enter the NVR’s Password (default: No password required, just leave blank.)

8
Step 3: If this is the first time that you use the program, please download and run the WebClient.exe.Control and follow the
pop up message.
Cloud ID : The Cloud ID can be found at right bottom corner of your monitor.
User Name: Input NVR’s User Name (Default: admin)
Password: Input NVR’s Password (No password required, just leave it blank)
①Click Tools > Internet Options > Security > Internet > Custom Level.
② Scroll down the mouse until you see ACTIVEX CONTROLS AND PLUG-INS.
(If you have Internet Explorer version 9 or 11, change ALLOW ACTIVEX FILTERING to DISABLE. Other versions of IE
broswer do not have this option.)
③ Change the following ACTIVEX controls to PROMPT:
Download signed ACTIVEX controls
Download unsigned ACTIVEX controls
Initialize and script ACTIVEX controls not marked as safe for scripting
2. When your PC is not located on the same LAN as the NVR (For example, in the case of you remote view your home
camera in your office computer.)
Step1. Open your Internet Explorer (IE) browser and visit www.e-seenet.com
Step2. Input Cloud ID, Username and Password to login.
Step4: Please click OK, and exit the “Security Settings” menu when you complete the settings.

9
5. Add Camera by Matching Code
1. When you use Match Code
1.1 Add new add-on cameras to your system.
1.2 Re-pair camera to NVR when camera cinnection failed. You need to delete the Network Unreachable channel at first, then
re-pair the camera to an unoccupied channel. (The status of unoccupied channel always shows No Video Source .)
Tips: IP cameras in pre-packed kits have already been paired to NVR. So cameras will auto connect to NVR once they are
plugged in power.
2.3 Click “Refresh”>Find camera’s IP>Click” Match Code”>Click “Yes”.The NVR will start to match code to the camera.
2.2 Right-click mouse in the blank of main interface, select “Video Manage”.
Network cables
CameraNVR
2.1 Power on the camera which has no video and connect this camera to the NVR through Network cable
2. Add camera by matching code.