Zte MF275R User manual

1
ZTE MF275R
Quick Start Guide

2
LEGAL INFORMATION
Copyright © 2015 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced,
translated or utilized in any form or by any means,
electronic or mechanical, including photocopying and
microlm, without the prior written permission of ZTE
Corporation.
The manual is published by ZTE Corporation. We reserve
the right to make modications on print errors or update
specications without prior notice.
Version No. : R1.0

3
Getting to Know Your Device
The device operates on the 4G/LTE networks and supports
voice and data service.
Appearance

4
1. micro-SIM card slot Insert your micro-SIM Card.
2. Reset button Reset your device.
3. External antenna
connector To attach antenna.
4. WPS button To activate the WPS Function.
5. Phone Standard RJ11 connector for the
telephone
6. LAN Ethernet connector to computer
7. Power socket Connector to the external power
supply
8. Power key Turn your device on or off.
9. Indicators Indicate the status of your device.
Indicators
Indicator State Description
Power Green steady AC power present
Off No AC power
Voicemail Green
blinking New voicemail waiting
Off No new voicemail

5
Battery
Green steady More than 50% discharging
(charger not present)
Green
blinking
More than 50% charging
(charger present)
Yellow steady 20%-50% discharging
(charger not present)
Yellow
blinking
20%-50% charging (charger
present)
Red steady
Less than 20%
discharging(charger not
present)
Red blinking Less than 20% charging
(charger present)
Off Battery not present
Wi-Fi
Green steady Wi-Fi on
Blinking Active data connection or
FOTA
Off Wi-Fi off

6
Network
Green steady Connected to the LTE
network
Green
blinking Roaming (LTE network)
Yellow steady Connected to the 4G
network
Yellow
blinking Roaming(4G network)
Red steady
No service, limited service,
searching for network, no
SIM Card or other abnormal
status
Signal
Strength
Green steady Strong signal
Yellow steady Weak signal
Red steady No service, limited service,
or searching for signal

7
Installation Guide
Installing the micro-SIM Card and battery
1. Slide the back cover and remove it
2. Insert the battery.

8
3. Install the micro-SIM Card.
WARNING!
• Switch off your device before installing or replacing the
micro-SIM card. Your device does not support placing
or inserting the micro-SIM Card while switched to the
ON position.
• Your device only supports micro-SIM Card. To avoid
damaging the device, please use the card that comes
installed or included in the box of the device.

9
Before You Begin
You can charge your device by using an adapter:
• Insert the charger lead carefully with the plug arrow
facing the bottom of the device.
• Do not use excessive force to insert the plug.
• Make sure the plug is facing the right way, and lined up
correctly. Insert it gently.
Connecting Your Device
Please refer to the following diagram for connecting your
computer and land line phone. If you want to use the
mobile network to connect to the Internet or use your land
line phone, you need to insert your micro-SIM Card rst.

10
Switching On Your Device
1. Press and hold the Power Switch to get started. Make
sure that the phone is on the hook before you power it
on.
2. Wait 1 ~ 2 minutes and then the Power and battery
indicator should be lit on.
Connecting to the Internet
Via Ethernet
1. Connect the Ethernet cable to the LAN port and your
computer.

11
2. Go to your favorite website on the PC connected to
your device via Ethernet cable to conrm your Internet
connection.
Via Wi-Fi
1. Use the Wi-Fi application on a client to search for
available wireless networks.

12
NOTE:
The client will obtain an IP address automatically.
2. Select the SSID of your device, and then click
Connect.
NOTE:
You can nd the default SSID on the label (under the back
cover) of your device.

13
3. Enter the password, and then click OK.
NOTE:
Please refer to the detailed User Guide online at
http://www.bell.ca/wirelesssupport.
4. Wait until the client is connected to your device
successfully.
5. Go to your favorite website to conrm your Internet
connection.

14
Conguring Your PC
The following procedure describes how to congure
the Internet Protocol in the Windows 7 for your Wi-Fi
connection.
1. Right-click Network and select Properties.
2. Select Change Adapter Settings.

15
3. Right-click Wireless Network Connection and select
Properties.

16
4. Select Internet Protocol Version 4 (TCP/IPv4) and
click Properties.

17
5. Select Obtain an IP Address Automatically and
Obtain DNS Server Address Automatically, and click
OK.
For more information, please refer to the detailed User
Guide online at http://www.bell.ca/wirelesssupport.