ZUUM MAHCL4X4V2 User manual

MAHCL4X4V2

Model: MAHCL4X4V2 a 4 in 4 out HDBaseT HDMI Matrix Switch allows you to route 4 HD sources to any 4 HD displays over Cat5 with HDMI receivers or

HDMI output. The 4x4 HDMI Matrix switch is a complete HD routing solution for whole home or commercial HDTV systems. It provides 3D support, Ultra

HD 4K2K, and 1U Rack mounting for professional installations. In addition, the MAHCL4X4V2 allows for effortless control of up to 4 devices through Ethernet

control, IR remote control, RS-232 and the front panel.

1.0 Features:

>Connect up to 4 HDMI sources to 4 HDMI displays (TV’s)

>High definition video up to 4K2K@60Hz@8bits, 1080p@60Hz@12bits

>Audio supports up to LPCM 7.1 @ 192KHz、Dolby TrueHD、DTS-HD MA

>Easy to use front panel control or included remote control for switching sources

>Built in Ethernet control, assign IP or set up as DHCP and enter IP into browser for computer-based control

>Built in RS232 console port for input / output selecting

>Front panel lights shows input /output connectivity and LCD display shows status

>Each output can be ether HDMI or Cat5 output. HE1L-HRX (up to 328’ no IR),HE1LBIR-70M-HRX (up to 229’ with IR) AND

HE1LBIR232-E-ARC-100M-HRX (up to 328’ with IR) are option Cat5 HDMI receivers.

>HDMI and HDCP compliant

2.0 Installation View:

3.0 Front Panel Indications:

Front Power LED Indication

Blue

Power on

Red

Standby

LED Off

Power Off

Front Input 1 ~ 4 LED Indications

Blue

Signal indication

LED off

No signal

Front Output 1 ~ 4 LED Indications

Blue

HDMI output indications

RED

HDBaseT output indication

LED off

Output unlinked

3.1 Front Button Functions:

POWER

Power on (Blue) / Standby (Red)

DOWN

Down

LEFT

Left

RIGHT

Right

ENTER

Select confirm key

Back to main/channel setting

3.2 LCD Panel Function:

Power on Main Screen

When the power is on and the main screen appears

Main MENU Option (SETTINGS):

*1 - SWITCH

7 - ETHERNET

2 – RS-232

8 - EDID

3 – IR TX

9 – FIRMWARE VER.

4 – IR RX

10 - KEYLOCK

5 – HDBASET IR ID

11 - SAVE

6 – MATRIX IR ID

12 - LOAD

4X4 HDMI MATRIX

Operation:

> Press UP or DOWN key to move *to select an item for setting and press ENTER key to enter into subpage.

> When the selected sub-page setting is completed, press the MENU button to return to the main page

4.0 LCD Main MENU Function Operations:

4.1 Switch：(Default: 1 2 3 4)

This function is used to switch the input/output port. Enter the SWITCH menu. Press the ENTER key, then the LCD second line INPUT will flash. Press

LEFT or RIGHT button to select the output to be modified. Then press Up or Down button to select the input port. After that, press ENTER to confirm setting.

It also works with INPUT/OUTPUT button of panel or IR remote

4.2 RS-232 Setting: (Default: Fix Mode)

HDBaseT RS-232 extender function works in two modes. Enter RS-232 SETTING MENU, press ENTER. The *will flash, then press UP or DOWN button

to select FIX MODE or MATRIX MODE. Press ENTER key to confirm setting.

FIX MODE is one to one transmission, RS-232 port 1 only works with HDBaseT port 1, RS-232 port 2 only works with HDBaseT port 2, and so on…

MAHCL4X4V2

RS-232 MATRIX MODE is based on the Status of the Matrix. The RS-232 transmission will follow the HDMI switching. In the example below, RS-232 port 1

works with HDBaseT port 1, 2 and 3. RS-232 port 4 works with HDBaseT port 4

OUT 1 2 3 4

IN 1 2 3 4

* FIX MODE

MATRIX MODE

HDMI RS232 RX

HDBaseT - 1

Projector

RS232 - 4

RS232 - 3

RS232 - 2

RS232 - 1

HDBaseT - 2

HDBaseT - 3

HDBaseT - 4

Projector

RS232 Cable

FIX MODE

* MATRIX MODE

MAHCL4X4V2

4.3 IR TX Setting (From matrix to remote locations): (Default IR TX: 0 0 0 0)

This function sets up the IR signal whether from MATRIX (by IR RX input jack) then sent to HDBaseT ports. Setting O the transmission is enabled, setting X

transmission is off.

This is the typical application when the user wants to control from the matrix side the remote destination like a TV.

After entering IR TX SETTING menu, press ENTER. Then LCD second line of text will flash. Press RIGHT or LEFT button to select the IR TX output to be

modified Press UP or DOWN button to select O or X. Then press ENTER to confirm setting.

O : on X : off

HDBaseT 1 2 3 4

IR TX

O X O X

HDMI - 4

RS232 - 4

HDMI - 3

RS232 - 3

HDMI - 2

RS232 - 2

HDMI - 1

RS232 - 1

HDBaseT - 1

HDBaseT - 2

HDBaseT - 3

HDBaseT - 4

Projector

Connect To PC 1

Projector

Connect To PC 1

Projector

Connect To PC 1

Projector

Connect To PC 4

PC 1

PC 2

PC 3

PC 4

HDMI RS232 RX

RS232 Cable

OUT P UT 1 2 3

INPUT 1 1 1

MAHCL4X4V2

IR RX

HDMI RX

IR TX

HDBaseT - 1

HDBaseT - 2

HDBaseT - 3

HDBaseT - 4

1 2 3 4

IR TX O X O X

4.4 IR RX Setting: (Default IR RX: 0 0 0 0)

This function sets up the IR signal whether from HDBaseT location is sent to MATRIX to control local device through the IR TX output jack. Setting O the

transmission is enabled, setting X transmission is off.

This is a typical application when the user wants to control from the remote location a source like a DVD player.

After entering IR RX SETTING menu, press ENTER. Then LCD second line of text will flash. Press RIGHT or LEFT button to select the IR RX input to be

modified. Press UP or DOWN button to select O or X. Then press ENTER to confirm setting.

O : on X : off

4.5 HDBaseT IR ID: (Default IR RD: 0 1 2 3)

This function must be set to have different ID per zone in order to avoid remote control IR1 conflicts from one zone to another.

After entering HDBaseT IR ID menu, press ENTER. Then LCD second line of text will flash. Press RIGHT or LEFT button to select the IR ID input to be

modified. Press UP or DOWN button to select the ID. Then press ENTER to confirm setting.

When you finish the HDBaseT IR ID setting, the HDBaseT remote controls IR1 must

also be setted with the same ID in order to perform the right operations. (See 5.0)

Remote IR ID setting mode: Press and hold the POWER button, then press the

number button which can be set from 0 to 9, total 10 groups. (See Diagram Below)

These settings on IR1 remote control have to be done the first time you use the IR1 or when you change the batteries.

HDBaseT 1

IR RX O X O

HDBaseT 1 2 3 4

IR ID

0 1 2 3

MAHCL4X4V2

IR TX

HDMI RX

IR RX

Player

Remote Control

Player

Remote Control

Player

Remote Control

Player

Remote Control

HDBaseT - 1

HDBaseT - 2

HDBaseT - 3

HDBaseT - 4

1 2 3 4

IR RX



O X

Pl ayer

4.6 Matrix IR ID: (Default IR ID: 4)

This function must be set to match the Matrix remote control IR1 with the matrix itself. A conflict with other remote controls is therefore avoided.

After entering MATRIX IR ID menu, press ENTER, the LCD LINE 1 number will flash. Then Press UP or DOWN button to select the number, and then press

ENTER to confirm.

When MATRIX IR ID setting is completed, MATRIX remote control IR1 must also be set to the same

ID in order to operate normal.

When you finish the MATRIX IR ID setting, the remote control IR1 that will control

locally the matrix, also is set with the same ID in order to perform the right

operations. (See 5.0)

Remote IR ID setting mode: Press and hold the POWER button, then press the

number button which can be set from 0 to 9, total 10 groups. (See 5.0)

These settings on IR1 remote control have to be done the first time you use the IR1 or when you change the batteries.

Matrix IR ID 4

MAHCL4X4V2

HDBaseT - 1

HDBaseT - 2

HDBaseT - 3

HDBaseT - 4

HDB a s e T 1 2 3 4

IR ID

0 1 2 3

＋

4.7 Ethernet

* IP Address

Subnet Mask

Gateway IP

DHCP Client

Media Type

MAC Filter

IP Address: (Default: 192.168.0.200)

This function can setup MATRIX host intranet ”IP Address”, press ENTER, the left-most number of second row will flash, then press the UP or DOWN button

to change the numbers, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to complete the setting.

NOTE: If DHCP Client is set to ENABLE you can not change IP.

Subnet Mask: (Default 255.255.255.0)

This function can setup MATRIX host intranet “Subnet Mask”, press ENTER, the left-most number of second row will flash, then press the UP or DOWN

button to change the numbers, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to complete the

setting. NOTE: If DHCP Client is set to ENABLE you can not change IP.

IP Address

192.168. 0.200

Subnet Mask

255.255.255.0

MAHCL4X4V2

MA T R I X IR ID 4

＋

Gateway: (Default 192.168.0.1)

This function can setup MATRIX host intranet “Gateway”, press ENTER, the left-most number of second row will flash, then press the UP or DOWN button to

change the numbers, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to complete the setting.

DHCP Client: (Default Disable)

When DHCP Clients setup to “Enable”, the MATRIX host will automatically get IP Address, Subnet Mask, Gateway, if setup as “Disable”, the MATRIX Host IP

Address needs to go through “ ETHERNET” menu to set IP Address, Subnet Mask, Gateway, press ENTER, the second row will flash, then press the UP or

DOWN to select DISABLE, ENABLE, then press ENTER to complete the setting. NOTE: If you set up as DHCP MAHCL4X4V2 Version up to (1.13 ) will

note show the IP address. You will need to go into your router to confirm exact IP address that was assigned or use our IP Finder.exe tool to know

what IP was assigned by your router.

Media Type: (Default AUTO)

This function can setup MATRIX host intranet “Media Type, press the ENTER, the second row will flash, then press the UP or DOWN button to select AUTO、

10MHalf、10MFull、100MHalf、100MFull, press ENTER to complete the setting.

MAC Filter: (Default Disable)

MAC Filter can setup with registered MAC Address in order to connect the MATRIX host Web UI. MAC Address is required by the Web page to fill in, this

function can only be setup as “DISABLE”, “ENABLE”, then press ENTER, the second row will flash, then press the UP or DOWN to select DISABLE, ENABLE,

then press ENTER to complete the setting.

4.8 EDID: (Default: 1080P LPCM-2CH)

Because the player output display resolution will be based on TV EDID, the Matrix provides two default EDID modes:” BUILD-IN MODE” and “COPY MODE”.

NOTE: 4K2K resolution you have to copy the EDID from your 4K2K monitor.

Gateway

192.168. 0. 100

DHCP Client

Disable

Media Type

AUTO

MAC FILTER

DISABLE

BUILD-IN MODE

COPY MODE

4.8.1 BUILD-IN MODE:

This mode supports video resolution 480p, 720p, 1080i/p at 24/50/60Hz, support 1080P LPCM two-channel audio and 5.1 channel. After enter BUILD-IN

MODE menu, press UP or DOWN key to select 1080P LPCM-2CH or 1080P LPCM-5.1CH, then press ENTER to confirm setting.

4.8.2 Copy Mode:

To fully support the TV resolution and audio mode, the matrix provides “COPY MODE” to copy TV EDID for input source reference. When using the copy

mode, recommend copying the lowest resolution TV EDID. Otherwise it may cause no picture display if the TV resolution is not able to support higher

resolution.

After entering COPY MODE menu, press UP or DOWN button to select the OUTPUT TV (1 to 4). Then press ENTER to confirm.

4.9 Version:

Display Matrix and WEB firmware version

4.10 Key lock:

Panel button/IR remote lock function to avoid Matrix changes. Under keylock mode press “POWER + MENU” to unlock

4.11 Save Setting:

Save current channel setting, total 10 sets available. When enter SAVE SETTING menu press UP or DOWN to select 1 of the 10 setting then press ENTER to

save.

4.12 Load Setting

Load channel setting, total 10 sets to load. When enter LOAD SETTING menu press UP or DOWN to select 1 of the 10 setting then press ENTER to save.

1080P LPCM-2CH

1080P LPCM-5.1CH

COPY MODE

From OUTPUT: 1

FIRMWARE

VERSION 1.13

SAVE SETTING SETTING

LOAD SETTING

SETTING 1

5.0 Remote Control Function (IR1):

> To command the matrix locally, setup the remote control IR1 ID with the same code of the Matrix (see 4.5). The default code is

4. (Power+4)

> Warning: These settings have to be done the first time you use the IR1 or when you change the batteries.

> IR ID setup: press and hold POWER button then press Number key

NOTE: In Standby mode: The IR Remote can only control POWER on/off.

Remote control button define:

(Symbol)

(Function)

Power

ON/Standby (same as Matrix)

Left

Left (same as Matrix)

Right

Right (same as Matrix)

Up (same as Matrix)

Down

Down (same as Matrix)

Enter

Confirm (same as Matrix)

Menu (same as Matrix)

Quick key 1

Quick key 2

Quick key 3

Quick key 4

No function

Turn off output

No function

Example: to connect output port 1 to input port 4, press the quick key 1 (OUTPUT 1) and then press the quick key 4 (INPUT 4).

6.0 REMOTE PC Control Function:

MAHCL4X4V2 supports RS232 and TCP/IP control by the same command as below:

6.1 For RS232 CONSOLE/IP:

Connect the RS232 CONSOLE port to the COM port of the host by an F/M RS232 straight cable (pin 2 to pin 2; pin 3 to pin 3, pin 5 to pin 5) Communication