Zyris Isolite 3 Installation guide

Isolite 3 Training
© 2018 Zyris, Inc. Isolite is a trademark of Zyris, Inc. All rights reserved.
MK9003-066-A1

Thank you for adding
Isolite 3 to your practice

What to expect today
WE’LL COVER THE FOLLOWING TOPICS
.Overview of the Isolite 3
.Installation of the Isolite 3
.Getting started
.How to select and place mouthpieces
.Cleaning and maintenance
3

ISOLITE 3
PREDICTABILITY
The Isolite 3 removes many of the negative
variables that can impact treatment including
soft tissue interference and low visibility.
PRODUCTIVITY
Continuous hands-free suction evacuates
water, saliva and debris for unsurpassed
moisture control.
RISK MANAGEMENT
The Isolite 3 shields soft tissue.
Designed with infection control in mind,
the single-use mouthpiece gently hugs
the vestibule and protects the airway.
4

ISOLITE 3
ILLUMINATION
The Isolite 3 provides unsurpassed visibility
with three levels of bright, long-lasting LED
illumination where you need it most.
QUALITY
Made of Liquidmetal®and manufactured in
the U.S.A., the Isolite 3 is lightweight but
mighty and made for years of use.
EASE
Unlike rubber dam placement, the Isolite 3
can be placed, removed and placed again in
seconds. Try doing that with traditional
isolation methods.
*Liquidmetal®is a registered trademark of Liquidmetal. All rights reserved. 5

ISOLITE 3
NEW AMBER LIGHT
Prevents the polymerization of light cure
resin-based composites, while still providing
illumination inside the mouth.
LIGHT MANAGEMENT TECHNOLOGY
The Isolite 3 utilizes multiple sensors to
dynamically manage thermal loads and light
output to prevent overheating.
INTELLIGENT POWER VACUUM BASE
The Power Vacuum Base can be set to
provide suction for the Isolite 3 by itself, the
Isolite 3 and an accessory, an accessory only
or completely turned off when cleaning and
sterilization are being performed.
6

Installation
7

What’s Included in the Box
.Instructions for Use
.Quick Start Guide
.Control Head with integrated hose
.Power Vacuum Base
.Six (6) Vacuum Light Pipes
.Cleaning tip adapter
.Accessory connector
.Direct-to-chair power adapter
.Isolite 3 power adapter
.O-ring lubricant
.Two (2) Barb adapters
8

STEP 1
Attach the end of
the vacuum connector hose to an
available High Volume
Evacuation (HVE) suction port.
Connecting the ISOLITE 3
9

Connecting the ISOLITE 3
[ STEP 1a ] Alternate method if no suction ports are available
10

STEP 2
Place the Control Head Hose on
an empty slot on the tool bar, as
shown.
Please contact your dealer or
chair manufacturer if you do not
have an opening in your tool bar.
Connecting the ISOLITE 3
11

STEP 3
Connect the Power Vacuum Base
onto the vacuum connector hose.
Connecting the ISOLITE 3
12

STEP 4
Plug in power adapter to
standard 120V power source.
For direct-to-chair connection
cable instructions, refer to the
Instructions For Use.
Connecting the ISOLITE 3
13

STEP 5
Plug in power adapter connector to
the top of the Power Vacuum Base.
Connecting the ISOLITE 3
14

STEP 6
Confirm light on Power Vacuum
Base is solid blue.
Refer to “Using the Power
Vacuum Base LED Indicator”
section in the Instructions For Use
if light is not solid blue.
Connecting the ISOLITE 3
15

STEP 7
Rotate the suction selection dial
to desired setting.
Allow up to 30 seconds for blue
light to appear.
Connecting the ISOLITE 3
16

Anatomy of
the ISOLITE 3

Easy Release Latch
Detachable Vacuum
Light Pipe
Integrated LEDs
Control Head &
Hose Integration
Dual Level Vacuum Control
Color Preview Setting
White & Amber
Light Setting
Three Light Level Setting
On / Off
The Isolite 3 control head is
integrated with the hose.
The only detachable parts
are the Vacuum Light Pipe
and the dual lever vacuum
controls.
Anatomy of
the ISOLITE 3
18

Turning the Light
On and Off
Press the top button once to turn
the system light on.
Press the top button and hold for
1 second to turn the system off.
19

Understanding the Light Settings
Tap the Power button once to enable the Low light setting.
Tap the Power button a second time to enable the Medium light setting.
Tap the Power button a third time to enable the High light setting.
1x 2x 3x
20