ZyXEL Communications 802.11g Wireless Ethernet Adapter 1-G-470 User manual

1
G-470
802.11g Wireless Ethernet Adapter
Quick Start Guide
Version 1.00
Edition 1
5/2006

2
About Your G-470
The G-470 is a wireless network adapter for your computer. It
allows your computer to connect to a wireless access point
(AP).
Installation Requirements
Before installation, make sure you have a computer with the
following:
• A Local Area Network (LAN) Ethernet port.
• Windows NT 4.0, Windows 98SE, Windows ME, Windows
2000 or Windows XP.
• Windows 98 SE users may need the Windows 98 SE CD.

3
Hardware Connections
Figure 1 The G-470: Rear Panel
The following table describes the rear panel of the G-470.
Follow the steps below to install the G-470 in your computer.
1Screw the antenna clockwise onto the antenna connector.
Make sure the antenna is securely screwed onto the
antenna connector.
2Use an Ethernet network cable to connect your computer
to the ETHERNET port for Internet access.
3Use the power adaptor provided with your G-470 to
connect an appropriate power source to the POWER
socket. Make sure the power source is on. Use only the
included power adaptor.
Label Description
1 Antenna connector
2RESET button
3ETHERNET port
4POWER socket

4
If the G-470 is properly connected, an icon similar to the
following will appear in the system tray (typically at the bottom
right of your desktop).
After you make the proper hardware connections, check the
lights on the front of the G-470.

5
Figure 2 The G-470: Front Panel
The following table describes the front panel of the G-470.
Light Description
SGNL The blinking frequency of the
SGNL light indicates the quality of
the wireless signal.
The light is
steady on.
Signal strength is 80% or more.
The light is
blinking once a
second.
Signal strength is between 60%
and 79%.
The light is
blinking twice a
second.
Signal strength is between 30%
and 59%.
The light is
blinking four
times a second.
Signal strength is below 29%.
The light is off. The wireless network is not
connected.

6
If any of these lights are not on, check your connections and
inspect your cables for damage. If the lights are still off,
contact your local vendor.
Internet Setup
You must first prepare your computer / computer network to
connect to the G-470 by setting up your IP address.
1Click start (Start in Windows 2000/NT) > Settings >
Control Panel.
WLAN The light is on. The device is connected to the
wireless network.
The light is
blinking.
The device is scanning for an
access point (AP).
The light is off. The device is not connected to the
wireless network.
ETHN The light is on. Ethernet is connected.
The light is
blinking
Ethernet is connected, and is
sending or receiving data.
The light is off. Ethernet is not connected.
SYS The light is off. The device is ready.
The light is
blinking orange.
The device is not ready, or is
rebooting.
PWR The light is on. The power is on.
The light is off. The power is off.
Light Description

7
2In the Control Panel, double-click Network Connections
(Network and Dial-up Connections in Windows 2000/
NT).
3Right-click Local Area Connection and then Properties.
4Select Internet Protocol (TCP/IP) and then click
Properties.
5Select Use the following IP Address and fill in an IP
address (between 192.168.1.12 and 192.168.1.254).

8
6Type 255.255.255.0 as the Subnet mask.
7If your Internet Service Provider (ISP) gave you Domain
Name System (DNS) settings, enter them in the Use the
following DNS server addresses fields. A DNS server
translates domain names (e.g. http://www.zyxel.com) into
the IP addresses your Internet browser uses to navigate
the web (e.g. 203.160.232.7). If you are not sure of your
DNS settings, contact your ISP.
8Click Advanced.
9Remove any previously installed gateways in the IP
Settings tab and click OK to go back to the Internet
Protocol TCP/IP Properties screen.
10Click OK to close the Internet Protocol (TCP/IP)
Properties window.
11Click Close (OK in Windows 2000/NT) to close the Local
Area Connection Properties window.
Close the Network Connections window (Network and
Dial-up Connections in Windows 2000/NT).

9
Configuration
Open your Internet browser and enter the URL of a web site
in the address bar.
Your G-470 automatically searches for wireless networks.
This may take a few minutes. If any other screens appear,
follow the directions in the screens.
If the web page opens correctly, your G-470 is ready to use.
If the web page does not open, you need to set up your
Internet connection. You should have information supplied by
your Internet Service Provider.
In your browser enter 192.168.1.11 (default) as the URL and
press ENTER. The G-470 Web Configurator login screen
displays as shown.

10
Figure 3 Login Screen
Type admin (default) as the username and 1234 (default) as
the password and click OK. The Status screen appears.