ZyXEL Communications P-2302R-P1C Instruction Manual

ZyXEL Confidential
360AUG0C0.rtf 1/35
ZyXEL
Firmware Release Note
P-2302R-P1C
Standard Version
Release 3.60(AUG.0)C0
Date: Mar 6, 2007
Author: Chun Hsing Chien

ZyXEL Confidential
360AUG0C0.rtf 2/35
ZyXEL P-2302R-P1C Standard Version
Release 3.60(AUG.0)C0
Release Note
Date: Mar 6, 2007
Supported Platforms:
ZyXEL P-2302R-P1C
Versions:
ZyNOS Version : V3.60(AUG.0) | 03/06/2007 18:53:22
Bootbase Version : V1.07 | 11/07/2006 10:32:08
Notes:
1. Bootbase version AOY107
2. SMT removed
3. Support Lifeline Auto detect
4. Support Multiboot 2.3
5. IVR User part removed
6. Remove Web Help Support temporarily
Known Issues:
1. Dialing number failed with some specific number
Dial "0000000000", DUT trigger PSTN relay
Dial "**********", DUT trigger IVR function
Dial "##########", DUT trigger internal call
2. Consultant transfer occurs noise on DUT.
3. Call waiting alert tone is like a fax tone.
4. Don’t support Japanese Dial tone/Busy/RBT tone.
5. Lack of Help Page in Web GUI.
6. DNS setting can't be set through auto provision.
7. PPPoE/NetBIOS allow between LAN and WAN does not work.
8. In Wizard mode, add BM rule - www, but LAN PC browser website will not match
the BM class.
9. Conference occur noise on DUT with G.729 codec when test 3-way Conference 3
times
10. STUN don't work when RTP port rang : 50000~ 50001.
11. Change back DUT from bridge to router mode, management IP can't be deleted or
change IP.
12. Change Country code through auto provision, the CallerID setting can't be changed

ZyXEL Confidential
360AUG0C0.rtf 3/35
Features:
Modification in V3.60(AUG.0) | 03/06/2007
1. Change to FCS version.
Modification in V3.60(AUG.0)b3 | 02/28/2007
2. [Bug Fix] [SPR number : 070227283] Caller side phone number write to max
character, when make VoIP call to Callee side, Callee offhook phone, Callee side
DUT will restart.
3. [Bug Fix] [SPR number : 070227287] PPPoE + Static IP" doesn't work.
4. [Bug Fix] [SPR number : 070227314]Sometimes BW LAN setting disappear.
5. [Bug Fix] [SPR number : 070227328] Inconsistency of PPPoE Static IP GUI.
6. [Bug Fix] [SPR number : 070227282] VAD default setting should be disable, but
now is enable, please change it.
7. [Bug Fix] [SPR number : 070227303] System wording issue. In GUI Maintenance >
System > General page, Note. "2.If chnage to Bridge mode, Please set Management
IP Address".
Modification in V3.60(AUG.0)b2 | 02/14/2007
8. Sync this f/w from P2301RL-P1 3.60(AOY.0)b5 source code.
Modification in V3.60(AUG.0)b1 | 01/19/2007
9. Modify this f/w from P2301RL-P1 3.60(AOY.0)b2 source code.
10. Modify phone 2 led, Support HTP.

ZyXEL Confidential
360AUG0C0.rtf 4/35
Annex A CI Command List
Command Class List Table
System Related Command Exit Command Device Related Command
Ethernet Related Command POE Related Command PPTP Related Command
Configuration Related Command IP Related Command ppp
dsp voice
System Related Command Home
Command Description
sys
adjtime retrive date and time from Internet
callhist
display display call history
remove <index> remove entry from call history
countrycod
e [countrycode] set country code
date [year month date] set/display date
domainname display domain name
edit <filename> edit a text file
extraphnum maintain extra phone numbers for
outcalls
add <set 1-3> <1st phone num> [2nd phone
num]
add extra phone numbers
display display extra phone numbers
node <num> set all extend phone number to remote
node <num>
remove <set 1-3> remove extra phone numbers
reset reset flag and mask
feature display feature bit

ZyXEL Confidential
360AUG0C0.rtf 5/35
hostname [hostname] display system hostname
logs
category
access
[0:none/1:log/2:alert/3:both]
record the access control logs
attack
[0:none/1:log/2:alert/3:both]
record and alert the firewall attack logs
display display the category setting
error
[0:none/1:log/2:alert/3:both]
record and alert the system error logs
ipsec
[0:none/1:log/2:alert/3:both]
record the access control logs
ike [0:none/1:log/2:alert/3:both] record the access control logs
javablocked [0:none/1:log] record the java etc. blocked logs
mten [0:none/1:log] record the system maintenance logs
upnp [0:none/1:log] record upnp logs
urlblocked
[0:none/1:log/2:alert/3:both]
record and alert the web blocked logs
urlforward [0:none/1:log] record web forward logs
clear clear log
display [access|attack|error|ipsec|ike|ja
vablocked|mten|urlblocked|urlfor
ward]
display all logs or specify category logs
errlog
clear display log error
disp clear log error
online turn on/off error log online display
load load the log setting buffer
mail

ZyXEL Confidential
360AUG0C0.rtf 6/35
alertAddr [mail address] send alerts to this mail address
display display mail setting
logAddr [mail address] send logs to this mail address
schedule display display mail schedule
schedule hour [0-23] hour time to send the logs
schedule minute [0-59] minute time to send the logs
schedule policy
[0:full/1:hourly/2:daily/3:weekly
/4:none]
mail schedule policy
schedule week
[0:sun/1:mon/2:tue/3:wed/4:thu/5:
fri/6:sat]
weekly time to send the logs
server [domainName/IP] mail server to send the logs
subject [mail subject] mail subject
save save the log setting buffer
syslog
active [0:no/1:yes] active to enable unix syslog
display display syslog setting
facility [Local ID(1-7)] log the messages to different files
server [domainName/IP] syslog server to send the logs
log
clear clear log error
disp display log error
online [on|off] turn on/off error log online display
resolve Resolve mail server and syslog server
address
mbuf
link link list system mbuf link
pool <id> [type] list system mbuf pool

ZyXEL Confidential
360AUG0C0.rtf 7/35
status display system mbuf status
disp <address> display mbuf status
cnt
disp display system mbuf count
clear clear system mbuf count
debug [on|off]
pwderrtm [minute] Set or display the password error
blocking timeout value.
rn
load <entry no.> load remote node information
disp <entry no.>(0:working buffer) display remote node information
nat <none|sua|full_feature> config remote node nat
nailup <no|yes> config remote node nailup
mtu <value> set remote node mtu
save [entry no.] save remote node information
smt not support in this product
stdio [minute] change terminal timeout value
time [hour [min [sec]]] display/set system time
trcdisp monitor packets
trclog
trcpacket
syslog
server [destIP] set syslog server IP address
facility <FacilityNo> set syslog facility
type [type] set/display syslog type flag
mode [on|off] set syslog mode
version display RAS code and driver version

ZyXEL Confidential
360AUG0C0.rtf 8/35
view <filename> view a text file
wdog
switch [on|off] set on/off wdog
cnt [value] display watchdog counts value: 0-34463
romreset restore default romfile
server
access <telnet|ftp|web|icmp|snmp|dns>
<value>
set server access type
load load server information
disp display server information
port <telnet|ftp|web|snmp> <port> set server port
save save server information
secureip <telnet|ftp|web|icmp|snmp|dns>
<ip>
set server secure ip addr
fwnotify
load load fwnotify entry from spt
save save fwnotify entry to spt
url <url> set fwnotify url
days <days> set fwnotify days
active <flag> turn on/off fwnotify flag
disp display firmware notify information
check check firmware notify event
debug <flag> turn on/off firmware notify debug flag
cmgr
trace
disp <ch-name> show the connection trace of this channel
clear <ch-name> clear the connection trace of this
channel

ZyXEL Confidential
360AUG0C0.rtf 9/35
cnt <ch-name> show channel connection related counter
socket display system socket information
filter
netbios
roadrunner
debug <level> enable/disable roadrunner service
0: diable <default>
1: enable
display <iface name> display roadrunner information
iface-name: enif0, wanif0
restart <iface name> restart roadrunner
ddns
debug <level> enable/disable ddns service
display <iface name> display ddns information
restart <iface name> restart ddns
logout <iface name> logout ddns
cpu
display display CPU utilization
filter
netbios
upnp
active [0:no/1:yes] Activate or deactivate the saved upnp
settings
config [0:deny/1:permit] Allow users to make configuration
changes. through UPnP
display display upnp information
firewall [0:deny/1:pass] Allow UPnP to pass through Firewall.
load save upnp information
save save upnp information

ZyXEL Confidential
360AUG0C0.rtf 10/35
ExitCommand Home
Command Description
exit exit smt menu
Ethernet Related Command Home
Command Description
ether
config dis
p
la
y
LAN confi
g
uration information
driver
cnt
disp <name> display ether driver counters
ioctl <ch_name> Useless in this stage.
status <ch_name> see LAN status
version see ethernet device type
pkttest
disp
packet <level> set ether test packet display level
event <ch> [on|off] turn on/off ether test event display
sap [ch_name] send sap packet
arp <ch_name> <ip-addr> send arp packet to ip-addr
debug
disp <ch_name> display ethernet debug infomation
level <ch_name> <level> set the ethernet debug level
level 0: disable debug log
level 1:enable debug log (default)
edit
load <ether no.> load ether data from spt

ZyXEL Confidential
360AUG0C0.rtf 11/35
mtu <value> set ether data mtu
accessblock <0:disable 1:enable> block internet access
save save ether data to spt
WAN Related Command Home
Command Description
wan adsl bert ADSL ber
chandata ADSL channel data, line rate
close Close ADSL line
coding ADSL standard current
ctrleint ADSL CTRLE response command
defbitmap ADSL defect bitmap status
dyinggasp Send ADSL dyinggasp
fwav Test the ADSL F/W available ping
fwdl Download modem code, but must reset first
linedata
near Show ADSL near end noise margin
far Show ADSL far end noise margin
open Open ADSL line
opencmd Open ADSL line with specific standard
opmode Show the operational mode
perfdata Show performance information,CRC,FEC, error
seconds..
rdata [start] [length] Read DSP CTRLE registers 512 bytes
reset Reset ADSL modem, and must reload the modem
code again
selftest
long ADSL long loop test
short ADSL short loop test
status ADSL status (ex: up, down or wait for init)
version ADSL version information
vendorid ADSL vendor information
utopia Show ADSL utopia information
cellcnt Show ADSL cell counter
display
shutdown Show the counter of rate adaptive mechanism
happening
rateup Show real status that rate adaptive mechanism
happened
rateadap [on|off] Turn on/off rate adaptive mechanism
dumpcondition [on|off] Turn on/off online debug information of rate
adaptive mechanism
sampletime [mins] Tune the sample time of rate adaptive mechanism
noisegt [dB] if noise margin is 3db greater than before, and
rate is worse than before, then system will do “L1
shutdown RA3”, default is 3db
noisemargin [dB] if noise margin is greater than this value, and rate
is worse than before, then system will do “L1
shutdown RA3”, default is 8db
persisttime [time] when the adaptive condition is matched system

ZyXEL Confidential
360AUG0C0.rtf 12/35
will continue to monitor the time period
ersisttime_ before doing 1 shutdown RA3_,
default is 30 seconds
timeinterval [mins] when “L1 shutdown RA3” is done twice, and still
can’t reach the max rate which system recorded,
it will delay a time period that the period base
time is”timeinterval” before starting again. The
time-based default is 2 hrs
defectcheck [on|off] Turn on/off detect table checking, default is on
txgain [value] Set the CTRLE register (0xc3), the value is from
0xfa to 0x06
targetnoise [value] Set the CTRLE register (0xc4), the value is from
0xfa to 0x06
maxtonelimit [value] Set the CTRLE register (0xc5), the value is from
0xfa to 0x06
rxgain [value] Set the CTRLE register (0xc6), the value is from
0xfa to 0x06
txoutputpwr [value] Set the CTRLE register (0xc7), the value is from
0xfa to 0x06
rxoutputpwr [value] Set the CTRLE register (0xc8), the value is from
0xfa to 0x06
maxoutputpwr [value] Set the CTRLE register (0xc9), the value is from
0xfa to 0x06
errorsecond
sendes Send current error second information
immediately
dygasprecover
dygasprecover level [value] By default is 100, after receiving 100 dying gasp
system will reboot
dygasprecover active [on|off| Turn on/off this mechanism
rsploss [1|0] Turn on means to response signal loss of CTRLE
immediately, default is off
atm test [fix|rand|period|oam|loopback] Generate ATM traffic
hwsar disp Display hwsar packets incoming/outgoing
information
clear Clear hwsar packets information
IP Related Command Home
Command Description
ip
address [addr] display host ip address
alias <iface> alias iface
aliasdis <0|1> disable alias
arp
status <iface> display ip arp status

ZyXEL Confidential
360AUG0C0.rtf 13/35
dhcp <iface>
client
release release DHCP client IP
renew renew DHCP client IP
status [option] show dhcp status
dns
query
server <primary> [secondary] [third] set dns server
stats
clear clear dns statistics
disp display dns statistics
httpd
icmp
status display icmp statistic counter
discovery <iface> [on|off] set icmp router discovery flag
ifconfig [iface] [ipaddr] [broadcast
<addr> |mtu <value>|dynamic]
configure network interface
ping <hostid> ping remote host
route
status [if] display routing table
add <dest_addr|default>[/<bits>]
<gateway> [<metric>]
add route
addiface <dest_addr|default>[/<bits>]
<gateway> [<metric>]
add an entry to the routing table to iface
addprivate <dest_addr|default>[/<bits>]
<gateway> [<metric>]
add private route
drop <host addr> [/<bits>] drop a route
smtp

ZyXEL Confidential
360AUG0C0.rtf 14/35
status display ip statistic counters
stroute
display [rule # | buf] display rule index or detail message in
rule.
load <rule #> load static route rule in buffer
save save rule from buffer to spt.
config
name <site name> set name for static route.
destination <dest
addr>[/<bits>] <gateway>
[<metric>]
set static route destination address and
gateway.
mask <IP subnet mask> set static route subnet mask.
gateway <IP address> set static route gateway address.
metric <metric #> set static route metric number.
private <yes|no> set private mode.
active <yes|no> set static route rule enable or disable.
traceroute <host> [ttl] [wait] [queries] send probes to trace route of a remote host
xparent
join <iface1> [<iface2>] join iface2 to iface1 group
break <iface> break iface to leave ipxparent group
ave anti-virus enforce
urlfilter
reginfo
display display urlfilter registration
information
name set urlfilter registration name
eMail <size> set urlfilter registration email addr
country <size> set urlfilter registration country

ZyXEL Confidential
360AUG0C0.rtf 15/35
clearAll clear urlfilter register information
category
display display urlfilter category
webFeature [block/nonblock]
[activex/java/cookei/webproxy]
block or unblock webfeature
logAndBlock [log/logAndBlock] set log only or log and block
blockCategory [block/nonblock]
[all/type(1-14)]
block or unblock type
timeOfDay [always/hh:mm]
[hh:mm]
set block time
clearAll clear all category information
listUpdate
display display listupdate status
actionFlags [yes/no] set listupdate or not
scheduleFlag [pending] set schedule flag
dayFlag [pending] set day flag
time [pending] set time
clearAll clear all listupdate information
exemptZone
display display exemptzone information
actionFlags
[type(1-3)][enable/disable]
set action flags
add [ip1] [ip2] add exempt range
delete [ip1] [ip2] delete exempt range
clearAll clear exemptzone information
customize
display display customize action flags
logFlags
[type(1-3)][enable/disable]
set log flags

ZyXEL Confidential
360AUG0C0.rtf 16/35
add [string]
[trust/untrust/keyword]
add url string
delete [string]
[trust/untrust/keyword]
delete url string
clearAll clear all information
logDisplay display cyber log
ftplist update cyber list data
listServerIP <ipaddr> set list server ip
listServerName <name> set list server name
tredir
failcount <count> set tredir failcount
partner <ipaddr> set tredir partner
target <ipaddr> set tredir target
timeout <timeout> set tredir timeout
checktime <period> set tredir checktime
active <on|off> set tredir active
save save tredir information
disp display tredir information
debug <value> set tredir debug value
nat
server
disp display nat server table
load <set id> load nat server information from ROM
save save nat server information to ROM
clear <set id> clear nat server information
edit active <yes|no> set nat server edit active flag
edit svrport <start port> [end
port]
set nat server server port

ZyXEL Confidential
360AUG0C0.rtf 17/35
edit intport <start port> [end
port]
set nat server forward port
edit remotehost <start ip> [end
ip]
set nat server remote host ip
edit leasetime [time] set nat server lease time
edit rulename [name] set nat server rule name
edit forwardip [ip] set nat server server ip
edit protocol [protocol id] set nat server protocol
edit clear clear one rule in the set
service
irc [on|off] turn on/off irc flag
resetport reset all nat server table entries
incikeport [on|off] turn on/off increase ike port flag
igmp
debug [level] set igmp debug level
forwardall [on|off] turn on/off igmp forward to all interfaces
flag
querier [on|off] turn on/off igmp stop query flag
iface
<iface> grouptm <timeout> set igmp group timeout
<iface> interval <interval> set igmp query interval
<iface> join <group> join a group on iface
<iface> leave <group> leave a group on iface
<iface> query send query on iface
<iface> rsptime [time] set igmp response time
<iface> start turn on of igmp on iface
<iface> stop turn off of igmp on iface
<iface> ttl <threshold> set ttl threshold

ZyXEL Confidential
360AUG0C0.rtf 18/35
<iface> v1compat [on|off] turn on/off v1compat on iface
robustness <num> set igmp robustness variable
status dump igmp status
stun
status Display the STUN Client ON/OFF
display Display the Stun Clinet infornation
debug 0:disable 1:keep line 2:nat type
4:nat lifetime 8: status 255:
all
send 1: shared request | 2: binding
request
Select send 1.TCP(no support) or 2.UDP
packets
keepline 1:enable 0:disable ON/OFF STUN keepline
t4 RD debug use
t5 RD debug use
pr
PPP Related Command Home
Command Description
ppp
autotrigger
on <remoteNodeIndex> turn on packet trigger, default is enable
off <remoteNodeIndex> turn off packet trigger
status show autotrigger status
Retry <interval> adjust PPP retrial interval
Configuration Related Command Home
Command Description
config The parameters of config are listed below.
edit firewa
ll
active
<yes|no>
Activate or deactivate the saved firewall
settings
retrie
ve
firewa
ll Retrieve current saved firewall settings

ZyXEL Confidential
360AUG0C0.rtf 19/35
save firewa
ll Save the current firewall settings
displa
y
firewa
ll Displays all the firewall settings
set
<set#> Display current entries of a set
configuration; including timeout values,
name, default-permit, and number of rules
in the set.
set
<set#>
rule <rule#> Display current entries of a rule in a set.
attack Display all the attack alert settings in
PNC
e-mail Display all the e-mail settings in PNC
? Display all the available sub commands
e-mail mail-server
<mail server
IP>
Edit the mail server IP to send the alert
return-addr
<e-mail
address>
Edit the mail address for returning an
email alert
e-mail-to
<e-mail
address>
Edit the mail address to send the alert
policy <full |
hourly |daily |
weekly>
Edit email schedule when log is full or per
hour, day, week.
day <sunday |
monday |
tuesday |
wednesday |
thursday |
friday |
saturday>
Edit the day to send the log when the email
policy is set to Weekly
hour <0~23> Edit the hour to send the log when the
email policy is set to daily or weekly
minute <0~59> Edit the minute to send to log when the
email policy is set to daily or weekly

ZyXEL Confidential
360AUG0C0.rtf 20/35
Subject <mail
subject> Edit the email subject
attack send-alert
<yes|no> Activate or deactivate the firewall DoS attacks notification emails
block <yes|no> Yes: Block the traffic when exceeds the
tcp-max-incomplete threshold
No: Delete the oldest half-open session
when exceeds the tcp-max-incomplete
threshold
block-minute
<0~255> Only valid when sets 'Block' to yes. The unit is minute
minute-high
<0~255> The threshold to start to delete the old half-opened sessions to minute-low
minute-low
<0~255> The threshold to stop deleting the old half-opened session
max-incomplete
-high <0~255>
The threshold to start to delete the old
half-opened sessions to
max-incomplete-low
max-incomplete
-low <0~255> The threshold to stop deleting the half-opened session
tcp-max-incomp
lete <0~255> The threshold to start executing the block field
set
<set#>
name <desired
name> Edit the name for a set
default-permit
<forward|block
>
Edit whether a packet is dropped or
allowed when it does not match the default
set
icmp-timeout
<seconds> Edit the timeout for an idle ICMP session before it is terminated
udp-idle-timeo
ut <seconds> Edit the timeout for an idle UDP session before it is terminated
connection-tim
eout <seconds>
Edit the wait time for the SYN TCP sessions
before it is terminated
fin-wait-timeo
ut <seconds> Edit the wait time for FIN in concluding a TCP session before it is terminated
tcp-idle-timeo Edit the timeout for an idle TCP session