1UP USA QUIK RACK SINGLE User manual

1.25” - 2” QUIK RACK SINGLE
Parts List:
1) 1.25’’ Hitch 11) Passenger Side Tray
2) Left 1.25’’ Side Plate 12) Bent Arm
3) Left Pivot Beam 13) 19” Strap
4) Cross Bar 14) Glide Bar
5) Black Bar 15) Red Lever
6) Right 1.25” Side Plate 16) 15° Plate
7) Gold Bar Knob 17) Blue Lever
8) Gold Bar 18) Driver Side Tray
9) Right Pivot Beam 19) 2” Hitch Adapter
10) Tap Plate
In The Box:
•1UP USA Quik Rack Single
•2 Gold Security Wrenches
•Velcro Strap
•Black ¼’’ Hex Wrench
Product Notes:
•Fits 16’’-29’’ wheels, up to 3.1’’ wide. For wider tires, use a Fat Bike Spacer Kit (sold separately).
•Rated to hold a bike up to 50 lb per bike spot.
•With the addition of two Add-Ons (sold separately), this rack can hold a maximum of three bikes.

INS01 2
Step 1:
•Remove rack from box.
•Unfold hitch parallel with the trays.
•Remove all cardboard supports.
•Remove plastic wrap around hitch.
Step 2:
•Position rack with hitch bar facing upwards and place on a stable nonabrasive surface.
•Locate the two Blue Levers and rotate outward 90°.
Note: If hitch on vehicle is 1.25’’, remove the installed 2’’ Hitch Adapter with supplied ¼” hex wrench.

3
Step 3:
•Rotate trays outward 90° into loading positon.
•Rotate Blue Levers back into original locking positon.
•Ensure Blue Levers are in position at all times when using the Rack.
Step 4:
•Insert Rack to desired depth in the receiver. The ball must be inserted a minimum of 2’’.
•Be sure that the silver ball does not stick out of the front of the hitch receiver.
2”

INS01 4
Tap Plate
Step 5:
•Pivot the Rack into the vertical position by pulling the Black Bar back and lifting upward on the Tap
Plate.
Note: See Rack Positions for more information.
Step 6:
•Tighten Security Bolt firmly with the gold Security Wrench provided.
•Attach Velcro Strap through safety chain loop on the side of the hitch receiver and loop around the
crossbar of rack for added safety.
Note: Do not tighten Security Bolt if Hitch Bar is not inserted into a hitch receiver.

5
Rack Positions
•Storage - traveling with no bicycles.
•Extra Clearance position - traveling with no bicycles, but a
large bumper or tire blocks storage position.
•Load Bikes - transport bikes.
•Rear Access - tailgate or trunk accessible with bikes on.
Pivoting the Rack
•Pull the Black Bar out away from the hitch while lifting up on Tap Plate.
•Rotate rack towards desired position and release black bar. Ensure it is fully engaged in the slots.
•Once positioned, tighten the Gold Bar Knob to keep the Black Bar in place.
Note: In the rear access position, the Black Bar will not lock into place.
Storage
Extra Clearance
Load Bikes
Rear Access

INS01 6
Loading Bikes
•Lift the Red Lever up parallel with the Glide Bar while pulling up on the Bent Arm. Do this on both
the driver and passenger side.
Note: Do not move the Bent Arms up without lifting the Red Lever.
•Set bike on trays in desired position.
•Pivot Bent Arms down to tire firmly.
Note: When loading multiple bikes stagger them to avoid seat and handlebar interference.
Unloading Bikes
•Compress bent arm/spools into tire slightly while lifting up on the Red Lever. This relieves pressure
and allows the red lever to easily unlock.
•Pivot Bent arms from bike to unload.

7
Wheel Settings
•The Rack is set to hold 26’’, 27.5’’, 29’’, or 700-C wheels. If bike tires are smaller, see instructions
below to adjust spools accordingly.
oWith a ½’’ wrench, remove the hex nut and washer.
oSlide the bolt out of the spools and re-assemble the spools in the desired wheel
position, firmly tightening the hex nut.
Additional Instructions
•Tighten the Security Bolt periodically.
•Remove rack from hitch at least every two weeks and clean hitch receiver so it does not seize in the
hitch enclosure.
•Wipe salt off of the nuts and bolts with a damp cloth to prevent corrosion.
•Check and retighten any hardware on the rack periodically to ensure proper working conditions.
Questions or comments? Contact our support team via email at [email protected]
24’’
20’’
16’’