2connect Aerpro APVFT12 User manual

APVFT12
Interface for Activation of Factory
Rear-View Camera Input and Video in Motion
Application:
Fiat 500/L/X/e 2013 - 2016
Fiat 500 Cabrio 2013 - 2016
Fiat 500 Abarth 2013 - 2016
For Vehicles with Uconnect 5.0” or 8.4” Systems and Grey 52 Way
OEM Connector. For NTSC Cameras Only.
v1
www
.aerpro.com.au

2
ABOUT THIS PRODUCT...
APVFT12
Reverse Camera Add On Interface for Uconnect 5” or 8,4” system with 52 pin
connector. Providesvideo input to connect a rear-view camera. Includes
video in motion functionality. Add on camera interface designed to allow the ad-
dition of an aftermarket reverse camera to the OEM screen. Designed for vehicles
with the grey 52 way connector, for NTSC camerasonly.
Prior to Installation
Read the manual prior to installation. Technical knowledge isnecessary for installa-
tion. The place of installation must be free of moisture and away from heat sources.
Please ensure you use the correct toolsto avoid damage to the vehicle or product.
Aerpro can not be held responsible for the installation of this product.
Technical Support
If you need assistance setting up or using your Aerpro product now or in the future, call Aerpro Support Australia
TEL: 03 – 8587 8898 FAX: 03 – 8587 8866 Mon-Fri 9am – 5pm AEST. If you would like to download a digital copy of this
manual, or other Aerpro manuals/software, please visit the http://aerpro.com website.
www
.aerpro.com.au

3
CONNECTION DIAGRAM/FITTING GUIDE
Connection Diagram
Interface Dipswitches
Vehicle/ navigation Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6
Video-in-motion permanent ON ON OFF OFF OFF OFF
Video-in-motion selective* OFF ON OFF OFF OFF OFF
* With Dip1 set to “OFF”, the included green cable is used to activate the
video-in-motion function.
Dipswitch Functions:
Dip 1 – Activates video in motion
Dip 2 – Rear-view camera coding
Dip 3 – No function
Dip 4 – No function
Dip 5 – CAN-bus termination resistor on the vehicle side
Interface
Harness
www
.aerpro.com.au

4
PIN ASSIGNMENT/INSTALLATION
Interface Pin Conguration
Cable Colour Pin-No. Assignment
Yellow Pin 4 CAN-HIGH – connection to the head-unit
Blue Pin 3 CAN-LOW – connection to the head-unit
Yellow/Black Pin 8 CAN-HIGH – connection to the vehicle
Blue/Black Pin 7 CAN-LOW – connection to the vehicle
Red Pin 1 +12V Permanent
Black Pin 5 Ground
Green Pin 6 Activation of video-in-motion function
(+12V = TV-free activated, only if Dip1=OFF)
White Pin 2 Trigger output (+12V DC 500mA)
(only if Dip2=ON and reverse gear engaged!)
Installation
NB: Before installation, switch off ignition, disconnect the vehicle battery and
remove the vehicle’shead unit.
The interface is installed behind the vehicle’s head unit. The RCA connectors
provide the factory aux signal and must remain connected.
Connecting Interface, Harness and Factory Navigation Unit
Interface
Harness
www
.aerpro.com.au

5
INSTALLATION
1. Connect the female 8pin Molex connector of the harnessto the male 8pin
Molex connector of the interface.
2. Transfer the female 52pin connector of the vehicle harness from the rear of
the head-unit into the male 52pin connector of the harness.
3. Plug the female 52pin connector of the harness into the male 52pin
connector on the rear of the head-unit.
Connection to the Rear-View Camera
Connect the video RCA of the rear-view camera to the female RCA connector
of the supplied harness.
Connect the white cable of the supplied harnessto the camera power supply
(+12V max 500mA). The white cable receives power when reverse gear is
engaged.
Rear-View Camera Coding
1. Set DIP switch “2” to “OFF” position
2. Turn on ignition
3. Wait until the head-unit hasbooted up
4. Set DIP switch “2” to “ON” position
5. Reset the system to complete the coding operation
Supplied Harness
www
.aerpro.com.au

6
INSTALLATION/SPECIFICATIONS
Activating the Rear View Camera
The rear-view camera will turn on automatically whenever the reverse gear is
engaged.
Activating Video in Motion Functionality
The video-in-motion can be activated by Dipswitch 1 or alternatively through
the use of the green cable (supplied)
Video-in-motion permanent
With Dip1 set to “ON”, the video-in-motion function is activated
Video-in-motion selective
With Dip1 set to “OFF”, the included green cable is used to activate the
video-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V
ACC.
+12V = TV-Free is activated
0V = TV-Free is not activated
www
.aerpro.com.au

7
NOTES

8
NOTES