2E G3022B User manual

LCD
MONITOR
СВІТЛОДІОДНИЙ
МОНІТОР
СВЕТОДИОДНЫЙ
МОНИТОР
G3022B
User Manual
Read this manual carefully before use.
.
.
www.2egaming.com

– 2 –
EN
Content
WARNINGS/SAFETY PRECAUTIONS
WARNINGS
ATTENTION
Important safety instructions
OPERATING INSTRUCTIONS
Components and auxiliary equipment
INSTALLATION
Installation of base
Installation of mount
FUNCTIONS
Description of buttons
Power indicator
Description of connection sockets
OSD MENU
Menu description
Specifications
Troubleshooting
Additional information
Warranty
3
3
3
4
5
5
6
6
7
8
8
8
8
10
10
13
14
14
42

– 3 –
EN
Warnings/Safety precautions
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNINGS/SAFETY PRECAUTIONS
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER AND BACK PANEL THERE
ARE NO USER-SERVICEABLE PARTS
INSIDE.
I CASE OF DAMAGE OR ERROR REFER SERVICING
TO QUALIFIED PERSONNEL.
Lightning flash with arrowhead symbol
within an equilateral triangle is intended
to alert the user to the presence of
non-insulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock in case of improper
usage of the product.
Exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance instructions in the literature
accompanying the product.
WARNING:
Do not put the monitor in rainy or foggy places to prevent from fire or electric shock.
To prevent scratches or damages to the LCD screen, do not knock, apply or rub the surface with sharp
or hard objects or stiff cloths as well as try not to touch the LCD screen with your hands.
Any modifications to this product that have not been clearly and explicitly approved in advance by the
manufacturer responsible for compliance with these regulations are forbidden.
ATTENTION:
Excessive sound pressure from earphones and headphones can cause hearing loss.

– 4 –
EN
Important safety instructions
1. Please read all the instructions carefully before using this product.
2. The instructions should be retained after reading for future reference.
3. Please immediately pull out the AC power plug from an adapter if there is an abnormal sound or
smell or the monitor has no picture, and contact after sales support.
4. The monitor should be kept free from rain, damp and dust to prevent electrical shock and short
circuits. Do not cover the ventilation openings with table clothes, curtains, newspapers etc.
5. The monitor should be kept away from heating objects or direct sunlight. This product requires
good ventilation. Allow 10 cm between the monitor and other appliances or built-in cabinet walls.
6. You may clean the display panel with a soft clean cloth after pulling out the power plug. Do not
repeatedly wipe the panel, nor scrape, tap or strike the panel with hard objects, etc.
7. Do not wipe the monitor with any petrol chemical or alcohol-based solvents, as it will lead to
product damage to the panel and cabinet.
8. Do not place the monitor on an unstable surface.
9. Do not place the power cord or other cables across a walkway in case it is trampled on, especially at
the points of connection to the plug, sockets and the power cord to the appliance.
10. Unplug the appliance during a lightning storm or when it is not used for a long period of time.
11. Unplug this product when the device, power cord or plug are damaged or if the device has been
exposed to liquid or moisture, has been mechanically damaged and does not work properly and
contact an authorized service centre immediately.
12. Keep this appliance away from liquids, splashes of water and do not place objects filled with liquids
on it.
13. Do not disassemble the back cover as it contains high voltages inside and will cause electric shock.
There is no spare parts inside. Internal adjustments and checks should only be conducted by
qualified professionals.
14. Do not place naked flame sources, such as lit candles on or near the monitor. Please pull out the
power plug and contact after sales support if there are abnormal objects or water in the monitor.

– 5 –
EN
Operating Instructions
Components and auxiliary equipment
Before assembling and installing, check for following items to be included in this display package.
Note: The redundant screws are used as spare screws.
45
45
45
45
45
45
45
45
Monitor x 1
Screws x 3
DP cable x 1
Stand stem x 1
Screws x 2 Mount hexagon irons x 4 Power Cable x 1
Base x 1
45
Shaft assembly x 1
45
45
Power Adapter 1
45
45
45
45
Microfiche and power
requirements label
Stand
User manual x 1

– 6 –
EN
Installation
Installation of base
1. Open the carton package, take out the foam and put it flat on the table top. Keep the
foam underneath the monitor before attaching the stand.
2. Take out the support and rotating shaft assembly and lock it with two screws.
3. Lock the bracket and base with a screw.
4. Put the assembled base into the corresponding slot of the back shell, gently press the
bracket to lock it into the lock, then hold the middle of the bracket, gently lift the body
twice, do not loosen, make sure it can be locked.
Screws
Screws

– 7 –
EN
Installation of mount
1. Open the carton package, take out the foam and put it flat on the table top. Keep the
foam underneath the monitor before attaching the stand.
2. Take out the wall mount assembly and lock the wall mount assembly with mount
hexagon irons.
3. Note: Hang the assembled product on a hard wall. Do not pinch the screen with your
hands during the hanging process to avoid damaging the screen.
Note: In order to prevent the monitor from falling when it is used on the wall, please install
it properly and do safety protection. Do not place or hang any objects on the wall
bracket, and the wall height should be within 2 meters.
Use studs with a post height of 42mm (not supplied)
Use studs with a post height of 31mm (not supplied)
Mount (not supplied)

– 8 –
EN
Functions
Description of buttons
Indicator: Steady blue light indicates the power is on and the monitor runs normally. Red
light indicates no video source and no horizontal or vertical signal detected or low voltage.
Please make sure that your computer is turned on and all video cables are fully plugged in
and/or connected.
1 2 3 4
Button Function
1 Power button: Turn on/o the monitor
2 Exit/Left button: Exit or return
3 Down button: Move down in the menu
4 Menu button: Enter sub-menus
5 Up button: Move up in the menu
Explanation of indicators

– 9 –
EN
w
*
w
c
HDMI interface
Use the HDMI cable to connect the HDMI IN interface
of the product to the HDMI OUT interface of a PC.
Use the HDMI-DVI cable to connect the HDMI IN interface
of the product to the DVI OUT interface of a PC.
(In general, PCs do not transfer video signals to the
monitor through the DVI OUT interface , and it is
necessary to connect a loudspeaker box additionally to
play sounds of PCs.)
Description of connection socket
* The bottom interface configuration at the back
of the monitor varies with products.
* Note: If the power cable or signal cable is
damaged, you must replace it with special soft
cables or special components purchased from
the customer care officer.

– 10 –
EN
OSD menu
Menu description
• The color and shape of the OSD menu of the actual computer may be slightly different
from them shown in the figure.
• Specifications of the OSD menu may change with improvements of functions without
prior notice.
Press the menu button on the control panel to access the monitor menu. The detailed
information of each menu can be found in the following sections.
1. Rocker key (Right) to enter the OSD main menu or enter sub-menus.
2. Rocker key (Up) to pattern of situations or move up in the menu.
3. Rocker key (Down) to enter the «GamePlus» or move down in the menu.
4. Rocker key (Left) to enter the Input Signal or exit the current screen.

– 11 –
EN
Level1 Level2 Level3
Game Settings
Standard Mode On / Off
RTS/RPG Mode On / O
FPS Arena Mode On / O
MOBA Arena Mode On / O
Adaptive-Sync On / O
Shadow Balance (Adjustment Bar; Range: 0 - 100) Default O
Response Time O/Normal/Fast/Ultrafast
Refresh Rate On/O:Top Right / Top Left / Bottom Right / Bottom Left
Game Crosshair On/O:Crosshair 1/Crosshair 2/Crosshair 3/ Crosshair 4/Crosshair 5/
Crosshair 6
Game Time On/O:15:00/30:00/45:00/60:00:Top Right/ Top Left/Bottom Right/
Bottom Left
Dynamic Brightness O/Normal/Expert/Elaboration
MPRT On / O
Ambient Lighting On / O
Picture Quality Settings
Brightness (Adjustment Bar; Range: 0 - 100) Default 80
Contrast (Adjustment Bar; Range: 0 - 100) Default 50
DCR On/O
Contextual Model O/On:Movie Mode/Reading Mode/Night Mode/Care Eyes Mode
Sharpness (Adjustment Bar; Range: 0 - 100) Default 0
Low Blue Light (Adjustment Bar; Range: 0 - 100) Default 0
Gamma 1.8 / 2.0 / 2.2 / 2.4 / 2.6 / S.curve
Aspect Ratio Wide Screen / 4:3 / 1:1 / Auto
Color Settings
Warm / Natural / Cool On / O
User1/User2/User3 O/On: Red, Green, Blue (Adjustment Bar; Range: 0 - 100) Default 50
Hue/Saturation Red, Green, Blue(Adjustment Bar; Range: 0 - 100) Default 50
PIP/PBP
PIP/PBP Mode O/PIP Mode/PBP 2Win 1:1
Sub-Signal Source DP/HDMI1/HDMI2
Audio Source Auto/DP/HDMI1/HDMI2
PIP Position Top Right / Top Left / Bottom Right / Bottom Left
PIP Size Small / Medium / Large
Swap —
OSD Settings
Language English / / …..
OSD Time Out (Adjustment Bar; Range: 0 - 100) Default 20
OSD H-Position (Adjustment Bar; Range: 0 - 100) Default 50
OSD V-Position (Adjustment Bar; Range: 0 - 100) Default 50
OSD Transparency (Adjustment Bar; Range: 0 - 100) Default 0
Hotkey1 Setting Brightness/Contrast/Volume/Mute/Shadow Balance/Game
Crosshair/Refresh Rate/Game Time/Contextual Model/ PIP/PBP
Mode/Input Signal/Dynamic Brightness
Hotkey2 Setting
Hotkey3 Setting
OSD Rotation Normal / 90 / 180 / 270
OSD Lock On/O

– 12 –
EN
Other Settings
Input Source Auto/DP/HDMI1/HDMI2
Volume (Adjustment Bar; Range: 0 - 100) Default 50
Mute On/O
Auto Power On/O
Eyeshield Remind On/O
Reset Yes/No
Input Source:HDMI2
Resolution:2560x1080@60Hz
Mode:Movie Mode
SN:

– 13 –
EN
Specifications
Model G3022B
Screen size 30’’Curve (1500)
Matrix type VA
Aspect ratio 21:9
Viewing angles 178 °/ 178 °
Displayable colours 16.7M (8-bit)
Resolution 2560x1080
FPS 100 Hz
Response time 1ms MPRT
Brightness 250 cd/m2
Contrast 3000:1
Interfaces xHDMI ., DP ., Audio out
Built-in speakers No
Screen tilt -5°~+20°
Height adjustment No
Screen rotation No
Monitor Power Options 48W, 12V, 4.0A
External power adapter parameters 100-240 V, 50/60 Hz, 4.0 A
Power consumption in operating mode
(max) <55W
Standby power consumption ≤0.5W
Wall mounting VESA 75x75
Package dimensions 794x172x405 mm
Weight (NET/GROSS): 5.2 kg/7.3 kg

– 14 –
EN
Troubleshooting
Problem Solution
Power cannot be turned on Check that both ends of the power cable are plugged into the socket
appropriately and the wall socket is operational
No Input signal message
Check that the signal line is connected properly.
Check that the power of the relevant peripherals is turned on.
Check that the Input option tnat has been selected matches with the
input signal.
Image colour or quality
deteriarates
Check that all the video settings are adjusted appropriately, such
as brightnešs, contrast, colour etc.
Display warning message Check that the input signal line is properly xed.
Select the correct input signal source
Additional information
The production date is encrypted in the serial number in the format
ERC2E *** YYYYMMDD *******, where: YYYYMMDD - year, month and day of production.

– 15 –
UA
Зміст
ПОПЕРЕДЖЕННЯ/ЗАПОБІЖНІ ЗАХОДИ
Основні правила з техніки безпеки
ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ
ВСТАНОВЛЕННЯ
ФУНКЦІОНАЛ
Роз’яснення до кнопок управління
на корпусі монітора
’
МЕНЮ
Технічні характеристики
Усунення основних несправностей
Додаткова інформація
Гарантія
16
16
16
17
18
18
19
19
20
21
21
21
21
23
23
25
26
27
27
43

UA
Попередження/Запобіжні заходи
Р
ИЗИК УРАЖЕННЯ ЕЛЕКТРИЧНИМ СТРУМОМ!
НЕ ВІДКРИВАТИ
ПОПЕРЕДЖЕННЯ/ЗАПОБІЖНІ ЗАХОДИ
-
.
.
.
-
-
, -
.
-
,
.
ПОПЕРЕДЖЕННЯ:
, -
.
, -
, -
.
,
-, , .
УВАГА
, .

UA
Основні правила з техніки безпеки
1. .
2.
.
3. /, -
,
, ’
.
4. , , ,
.
. , -
, .
5. ,
. .
, , 10 .
6. ’ ,
. ,
, , .
7. , ,
, .
8. .
9. , ,
, ’ , ’-
.
10.
.
11. , , ,
,
, .
12. , ’,
.
13. ,
. -
, .
.
14. / ’, . , ’-
’ ,
.

– 18 –
UA
Інструкція з експлуатації
Комплектація та допоміжне обладнання
.
45
45
45
45
45
45
45
45
Mo x 1
x 3
DP x 1
x 1
x 2
x4
x 1
x 1
45
x 1
45
45
1
45
45
45
45
Stand
x 1
.

– 19 –
UA
Встановлення
Встановлення основи
1. ,
. , .
2. .
3. .
4. ’ ,
, ,
, , ,
.
Screws
Screws

– 20 –
UA
Монтування кріплення
1. ,
. ,
.
2.
.
3. : .
, .
Примітка: ,
.
2 .
Use studs with a post height of 42mm (not supplied)
Use studs with a post height of 31mm (not supplied)
Mount (not supplied)
.
( )
Table of contents
Languages:
Other 2E Monitor manuals