2gig Technologies 2GIG-DW14-433 User manual

Copyright © 2015 Nortek Security & Control LLC 1
2GIG-DW14-433
THIN DOOR/WINDOW CONTACT
INSTALLATION INSTRUCTIONS
TheThinDoor/WindowContact(2GIG‐DW14‐433)isdesignedforuse
ondoors,windows,andotherobjectsthatopenandclose.It
communicateswiththecontrolpanelusingthe433MHzfrequency.
Whenthemagnet(whichismountednearthesensor)movesaway
fromorclosertothedoorcontact’ssensor,signalsaretransmittedto
thecontrolpanel.Thedoorcontactalsohasanexternalinputthat
acceptsconnectionsfromNormally‐Closed(NC)drycontactdevices.
Foraddedprotection,itisalsoequippedwithacovertamper.
Figure 1 ThinDoor/WindowContact—SensorandMagnet
Box Contents
Verifythatthepackageincludesthefollowing:
•1—ThinDoor/WindowContact
•1—RareEarthMagnet
• 2—PhillipsHeadScrews
•2—3‐Volt(3V)LithiumCoinBatteries
•2—AdhesiveFoamTape
•1—12in(30cm)WireLead
Testing the Thin Door/Window Contact
Beforemountingthedoorcontactatthedesiredlocation,performa
walktesttoverifythatitcanestablishgoodRadioFrequency(RF)
communicationswiththecontrolpanel.
NOTE: TofullytesttheThinDoor/WindowContact,seethe
controlpanel’sInstallationandProgrammingGuide.
Mounting Guidelines
Usetheseguidelineswheninstallingthedoorcontactforinternal
switchusage:
•MountSensorswithin100ft(30m)oftheControlPanel.
Althoughthetransmittermayhavearangeof350ft(106.7m)
openair,thesensorlocationcanhaveasignificanteffecton
range.Inopen/unobstructedsituations,thetransmitterrange
maybegreater.Inadversewirelessconditions,changingthe
sensororientationmayleadtoimprovedrange.
•MountSensorsatLeast4.7in(12cm)AbovetheFloor.
Placingsensorsslightlyabovefloorlevelhelpstominimize
possiblesensordamage.
•Singlevs.DoubleDoorInstallation.Forsingle‐door
installation,mountthesensoronthedoorframeandthe
magnetonthedoor.Fordouble‐doorinstallation,mountthe
sensorontheleast‐useddoorandthemagnetonthemost‐
useddoor.
•DoNotExposeSensorstoMoistureorExtremeTemperature.
Itisbesttomountsensorsinadrylocationwherethe
operatingtemperaturedonotexceed32°to120°F(0°to49°
C).
•KeepSensorsandMagnetsAwayfromMetal/Metallic
Surfaces.Tokeepsensorsandmagnetsawayfrommetalor
metallicsurfaces(forexample,foilwallpaper),itis
recommendedthatyouusespacers(notincluded).Youshould
alsoavoidmountingsensorsinareaswherethereisalarge
quantityofmetalorelectricalwiring(forexample,neara
furnaceorinautilityroom).
•AlignMagnetwithSensor.Makesurethealignmentarrowon
themagnetpointstothecenteralignmentmarkonthesensor
(seeFigure1ThinDoor/WindowContact—Sensorand
Magnet).
Mounting the Thin Door/Window Contact
Usethefigurebelowasaguidelinewhenmountingthedoorcontact.
Instep7below,youhavetheoptiontomountthedoorcontactwith
anexternalinputwireforanNCdrycontactdevice.
Figure 2 ThinDoor/WindowContact—BackplateandBatteryCompartment
Tomountthedoorcontact:
1Atthetopofthesensor,pressdownonthecliptounlockthe
sensor’sbackplate.Then,gentlypulldownonthebackplateto
removeit.
2Onthebackplate,drill‐throughtopandbottommountingholesif
needed(seeFigure2ThinDoor/WindowContact—Backplateand
BatteryCompartment).
3Holdingthebackplatelocation,placethebottommountinghole
asfollows:
•SingleDoorInstallation.Atthedesiredlocationonthedoor
frame.
•DoubleDoorInstallation.Atthedesiredlocationontheleast‐
useddoor.
AThinDoor/WindowContactSensor
BThinDoor/WindowContactMagnet
CAlignmentMarksonSensor
DAlignmentArrowonMagnet
AAccessholeforexternalinputwire(onbackplate)
BTopandbottommountingholes(onbackplate)
CExternalinputwirejack(onsensor)
DTamperswitch(onsensor)
E3‐Volt(3V)lithiumcoinbatterycompartments(onsensor)
FMetalclipsforremovingbatteries(onsensor)

2Copyright © 2015 Nortek Security & Control LLC
Thin Door/Window Contact | Installation Instructions
IMPORTANT: Tominimizetheriskofpotentialsensordamage,
alwaysmountthesensorataminimumheightof4.7in(12
cm)fromthefloor.
4Usingthetwo(2)PhillipHeadScrews(provided),securethe
backplatethedoor(ordoorframe).
5Ensurethatthealignmentarrowonthemagnetislinedupwith
themiddlemarkonthesensor(seeFigure1ThinDoor/
WindowContact—SensorandMagnet).
6Usetheadhesive(provided)tosecurethemagnetasfollows:
•SingleDoorInstallation.Onthedoor.
•DoubleDoorInstallation.Onthemost‐useddoor.
IMPORTANT: Themagnetmustbenomorethan0.4in(1cm)
awayfromthesensor.
NOTE: Ifyouarenotusinganexternalinputwire,skipstep7
andcontinuewithstep8.
7Ifyouareusinganexternalinputwire,dothefollowing:
7a Threadtheexternalinputwirethroughthebase.
7b Insertthetwo‐pinconnectorintotheexternalinputwire
jackonthe(seePartCinFigure2ThinDoor/Window
Contact—BackplateandBatteryCompartment)cover.
8Replacethesensorbackplate.Ifapplicable,ensurethatthe
externalinputwireisconnectedtotheNCdrycontactdevice.
NOTE: TolearnhowtoprogramasensorintotheControlPanel,
seetheControlPanel’sInstallation&ProgrammingGuide.
Inserting and Replacing the Batteries
Toinsertorreplacethebatteries:
1Atthetopofthesensor,pushdownthecliptounlockthe
sensor’sbackplate.Then,gentlypulldownonthebackplateto
removeit.
2Placeasmallflatheadscrewdriverintheslotbetweenthemetal
clipandbattery(seePartFinFigure2ThinDoor/Window
Contact—BackplateandBatteryCompartment).
3Holdingdowntheraisedplasticedgeinthebattery
compartment,gentlytwistthescrewdrivertopopouteach
battery.
IMPORTANT: Alwaysdisposeand/orrecycleusedbatteriesin
accordancewiththehazardouswasterecoveryand
recyclingregulationsforyourlocation.Yourcity,state,or
countrymayalsorequireyoutocomplywithadditional
handling,recycling,anddisposalrequirements.
4Insertthereplacementbatteriesinthecompartment.Theplus
(+)signofbothbatteriesshouldbefacingupandtheminus(‐)
sidefacingdown.
WARNING: Failuretofollowthesewarningsandinstructions
canleadtoheatgeneration,rupture,leakage,explosion,
fire,orotherinjury,ordamage.Donotinsertthebattery
intothecompartmentinthewrongdirection.Always
replacethebatterywiththesameorequivalenttype(see
InsertingandReplacingtheBatteriesonpage2).Never
rechargeordisassemblethebattery.Neverplacethe
batteryinfireorwater.Alwayskeepbatteriesawayfrom
smallchildren.Ifbatteriesareswallowed,promptlyseea
doctor.
Specifications
Regulatory Information
Limited Warranty
ThisNortekSecurity&Controlproductiswarrantedagainstdefects
inmaterialandworkmanshipfortwo(2)years.Thiswarranty
extendsonlytowholesalecustomerswhobuydirectfromNortek
Security&ControlLLCorthroughNortekSecurity&ControlLLC’s
normaldistributionchannels.NortekSecurity&ControlLLCdoes
notwarrantthisproducttoconsumers.Consumersshouldinquire
fromtheirsellingdealerastothenatureofthedealer’swarranty,if
any.
TherearenoobligationsorliabilitiesonthepartofNortekSecurity
&ControlLLCforconsequentialdamagesarisingoutoforin
connectionwithuseorperformanceofthisproductorother
indirectdamageswithrespecttolossofproperty,revenue,or
profit,orcostofremoval,installation,orreinstallation.Allimplied
warrantiesforfunctionality,arevalidonlyuntilthewarranty
expires.ThisNortekSecurity&ControlLLCWarrantyisinlieuofall
otherwarrantiesexpressedorimplied.
NortekSecurity&ControlLLC
2GIG
1950CaminoVidaRoble,Suite150
Carlsbad,CA92008‐6517USA
FortechnicalsupportintheUSAandCanada:
855‐2GIG‐TECH(855‐244‐4832)
Email:[e-mail]
Visitwww.nortekcontrol.comfortechnicalsupporthoursofoperation
FortechnicalsupportoutsideoftheUSAandCanada:
Contactyourregionaldistributor
Visitdealer.2gig.comforalistofdistributorsinyourregion
77‐000014‐001Rev.D
WirelessSignalRange 350ft(106.7m),openair,withWireless
ControlPanel
CodeOutputs Alarm;AlarmRestore;Supervisory;Low
Battery;ExternalAlarm;ExternalRestore;
Tamper;Ta mperRestore
TransmitterFrequency 433.92MHz(crystalcontrolled)
UniqueIDCodes Overone(1)milliondifferentcode
combinations
SupervisoryInterval 70minutes
ExternalInput AcceptsN/Cdrycontactdevices
MagnetDimensions(LxWxH) 1.3x0.435x0.312in(3.3x1.1x0.79cm)
MagnetType RareEarth
SensorDimensions(DxH) 2.59x1.03x0.49in(6.58x2.62x1.24cm)
Weight(includingbattery&magnet) 1.1oz(31.2g)
HousingMaterial ABSPlastic
Color White
OperatingTemperatu re 32°‐120°F(0°‐49°C)
RelativeHumidity 5‐90%Non‐Condensing
Battery(included) Two(2)PanasonicCR2032orequivalent
Lithiumbatteries
Certification CEandRCM