360 Hunting Blinds 360 Series User manual

ASSEMBLY
MANUAL
360 SERIES
2022 EDITION

360 SERIES
ASSEMBLY MANUAL
Follow this guide to assemble a series 360 Hunting Blind
from start to finish.
If you purchased a tower stand with your blind, please
refer to that assembly guide to assemble the tower first, the
come back to finish the setup of the blind on the fully
assembled tower stand.
INTRODUCTION
SUPPLIES NEEDED
PARTS LIST
• T-50 construction stapler
• Utility knife
• Impact Driver
• Caulk gun
• Level
• Flat bar or prybar
• 4 - 8” – 12” Pressure Treated 4 X 4s
360 PRO
• 1 floor
• 1 floor carpet
• 8 wall panels with
standard windows
• 4 wall panels with
archery windows
• 1 door panel
• 1 roof
• Caulk
• 1 touch up kit
• 1 set of keys
360 STANDARD
• 1 floor
• 1 floor carpet
• 12 wall panels
• 1 door panel
• 1 roof
• Caulk
• 1 touch up kit
• 1 set of keys
360 PRO XL
• 1 floor
• 1 floor carpet
• 8 wall panels with
standard windows
• 6 wall panels with
archery windows
• 1 door panel
• 1 roof
• Caulk
• 1 touch up kit
• 1 set of keys
At no time shall 360 Hunting Blinds be liable for any accidents due to normal or improper use of blinds or tower stands.
We recommend that you follow standard safety procedures when entering and exiting the blind, or climbing or decending the
ladder.
Always use a gear rope to raise and lower your equipment into the blind.
Always use the handrail with both hands when climbing the ladder.
Never use the door handle to pull yourself onto the platform or stabalize your entry and exit.
SAFETY DISCLAIMER

360HUNTINGBLINDS.COM PAGE 3
STEP 2
Align the carpet roll to the edges of
the blind floor and begin fastening
with the T50 Construction Stapler.
Work from one end of the floor to the
other, working out the wrinkles and
continually aligning the edges while
going along. If some carpet overhangs
past the edge of the floor, use a utility
knife to trim the carpet so it is no lon-
ger overhanging.
INSTALL THE CARPET
STEP 1
Install 8” – 12” 4x4s into the
pockets on the floor and secure with
3 – 3” deck screws per foot.
If you purchased a tower stand you
may skip this step.
INSTALL THE LEGS

360HUNTINGBLINDS.COM PAGE 4
STEP 4
Run a 3/8” bead of caulk along the
leading edge of the first panel. Make
sure it’s right along the outside of the
panel right at the point where the sec-
ond panel will join up to the first. Re-
member, the better the seal the longer
the blind will last!
CAULK PANEL EDGE
STEP 3
Set the first panel into place. Have one
person hold the top of the panel while
another person aligns the bottom.
Make sure the corners of the panel
match with the corner of the floor and
that the panel doesn’t gap away from
the floor.
Use a screw to secure the panel to the
floor from the inside.
INSTALL THE FIRST PANEL

360HUNTINGBLINDS.COM PAGE 5
STEP 6
REPEAT
Repeat steps 4 and 5 for the remaining
panels except the last wall panel and
the door.
STEP 5
Start at the top of the panel, align
the tops and outsides of the panels
to make sure they are even. Work
the panels to align the outside edges
and fasten the panels together with a
screw at the top. Then, while working
from top to bottom, keep everything
aligned and run two more screws to
secure the panels together.
INSTALL WALL PANELS

360HUNTINGBLINDS.COM PAGE 6
STEP 8
Now that the roof is resting on top of
the walls and set back out of the way,
caulk and install the final wall panel.
INSTALL THE LAST PANEL
STEP 7
Lift the roof to the top of the blind and
rest it on top ofthe walls.
Balance it on the back walls of the
blind far enough to make room for
installing the remaining wall panel
and door panel.
LIFT THE ROOF

360HUNTINGBLINDS.COM PAGE 7
STEP 10
Center the roof on the blind.
Start above the door and screw
through the top of the wall panel into
the roof panel with SHORT screws
Align the panels with the roof by
pushing and pulling on each panel as
you work your way around the blind
aligning the panel joints with the
joints in the roof.
Use plenty of screws to make sure the
roof can’t come off.
FASTEN THE ROOF
STEP 9
With the roof and wall panels in place
it’s time to install the door. Caulk both
wall panels, then set the door panel
in place and fasten like the other wall
panels. If you fastened any wall panels
to the floor, remove those screws for
this step so you can shift wall panels
for a tighter seal to the door.
INSTALL THE DOOR PANEL

360HUNTINGBLINDS.COM PAGE 8
STEP 12
Use the touch up paint to touch up
any nicks or scratches that can occur
during setup. Any unpainted siding
has more risk of rot than painted
siding so be particular when painting.
TOUCH UP
STEP 11
If there are wrinkles in the carpet, use
a flat bar or prybar to lift the wall pan-
els and push wrinkles back out. Then
fasten the wall panels to the floor with
several screws.
FASTEN THE WALLS