3nStar PTE0905 User manual

1
15” All-In-One POS System i5 9th Gen
USER MANUAL
PTE0905

Safety and Warranty
1. Read these safety instructions carefully.
2. Disconnect from power outlet before cleaning, disassembly or transport. Do not use liquid
or spray detergents for cleaning. Use a damp cloth only and avoid any prolonged contact
with moisture.
3. Keep the unit away from humidity.
4. Place the unit on a sturdy surface before servicing or operation to prevent accidental
drops.
5. The openings on the enclosure are for ventilation. Do NOT cover the openings.
6. Make sure the voltage and load ratings of the power source are correct before connecting
the equipment to the power outlet.
7. Position the power cord to prevent accidental tripping. Do not twist, pinch or clip the power
cord.
8. All cautions and warnings printed on the equipment should be followed.
9. If the equipment is not used for a long time, disconnect it from the power source.
10. Never pour any liquid into openings. This could cause fire or electrical shock.
11. For safety reasons, only qualified service personnel should open and service the
equipment.
12. If any of the following situations arises, get the equipment checked by service personnel:
•The power cord, plug, or adapter is visibly damaged.
•Liquid has entered into the equipment.
•The equipment has been exposed to moisture.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
13. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE
THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F).

T
Ta ab bl le e o of f C Co on nt te en nt t
Chapter 1
Induction ………………………………………………………………………….1
Main features……………………………………………………………………………………….1
15” PTE0905……………..…...………………………………………………………………….....2
Optional Peripheral…....……......………………………………………………………………….3
Stand…………………....……......………………………………………………………………….4
Adjustable angle………………….………………………………………………………………...6
Dimension………….………………………………………………………………………………..7
Rear I/O panel connectivity………………………………………………………………………..8
Packing list……………..………...…….…………………………………………………………...9
Chapter 2
Hardware Installation & Setting………...……………………………………..………10
Optional Device Installation
Customer Display Installation ………………………………………...…………………..…....10
Install Add-on Device ………………………………………...………………………..…..…....11
Remove & Install Cable Cover………………...…………………………………….........……11
Device status setting…………….………………………………..…………………….....……12
Chapter 3
Driver & Utility Installation and setup……….………………………………….…..13
Installation Order ……….………………………………..…………………….......... ……13
Chipset ……….………………………………..…………………….......... ……14
Audio ……….………………………………..…………………….................................. ……15
Graphics….………………………………..……………………...................................... ……16
Intel ME….………………………………..……………………...................................... ……17
Sensor….………………………………..……………………...................................... …..…18
OPOS….………………………………..……………......…...................................... ………19
Cash Drawer ………………………..……………………................. ........................... ……20
Chapter 4
Specifications…………………………………………………………….……..21
Chapter 5
Troubleshooting……………………..………………………………………………………………22

1
C
Ch ha ap pt te er r 1 1
I
In nt tr ro od du uc ct ti io on n
M
Ma ai in n F Fe ea at tu ur re es s
⚫Platform: INTEL Coffee Lake platform support INTEL gen 9 processor
⚫Panel PC with Dual hinge stand: Adjustable angle and height
Improve the viewing angle, enhance the user experience, can also be Desktop, Pole or
Wall-mounted.
⚫Shared Peripherals: Share the same peripherals with XPOS

2
1
15 5” ” P PT TE E0 09 90 05 5
Wifi 802.11 a/b/g/n/ac & Bluetooth 4.2(Optional)
15” 1024 x 768
P-cap Touch Display
Light Sensor
Speaker
Speaker
LCM or 2nd 10” non-touch LCD (Smart DP)
Side USB
Power Button
Power LED
Off > Red
On > Blue
IO

3
O
Op pt ti io on na al l P Pe er ri ip ph he er ra al l P PT TE E0 09 90 05 5
PTE0905-M10

4
Wall Mount Bracket

5
C
Ca ab bl le e M Ma an na ag ge em me en nt t ( (P PT TE E0 09 90 05 5) )

6
A
Ad dj ju us st ta ab bl le e A An ng gl le e ( (P PT TE E0 09 90 05 5) )

7
D
Di im me en ns si io on n ( (P PT TE E0 09 90 05 5) )

8
R
Re ea ar r I I/ /O O P Pa an ne el l C Co on nn ne ec ct ti iv vi it ty y ( (P PT TE E0 09 90 05 5) )
IO Default
I/O Port
Connector Type
Application
Video Ports
HDMI x1
For 2nd HDMI Monitor
PUSB 24V
24V Power USB
Smart I/O
Including 5V/12V/24V (BIOS select) and USB 2.0 x 2
and Com port x 1
I/O cables
20V in
20V DC in (130W)
Cash drawer
12V / 24V adjust by bios
USB DP or Smart
DD
USB TC x1 (USB DP, SMART DD by BIOS select)
For 2nd USB DP
Monitor
Serial port
RJ45 Com port x 3
USB
USB 2.0 x 2, USB 3.0 x 2
Ethernet
Giga Lan

9
P
Pa ac ck ki in ng g L Li is st t ( (P PT TE E0 09 90 05 5) )
Standard
Optional & Peripherals
1
15”
2
20V 130W Power Adaptor
3
AC Cord Cable
4
RJ-45 to D-sub9 Convert Cable x1

10
C
Ch ha ap pt te er r 2 2
H
Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n & & S Se et tt ti in ng g
Optional Device Installation
1. Customer Display Installation,
Install Pull up the connector
Fasten 2 screws for customer display

11
2. Install 2nd display (integrated type) PTE0905-M10 on Smart DP
Remover Plastic Cover
Plug in ID device (USB) and
fix it via 1 x M3 screw

12
2. Remove & Install Cable Cover
Remove Cable Cover
Install Cable Cover
Device status setting

13
C
Ch ha ap pt te er r 3 3
D
Dr ri iv ve er r & & U Ut ti il li it ty y I In ns st ta al ll la at ti io on n a an nd d S Se et tu up p
1. Chipset
•Locate chipset folder and double click on [ SetupChipset ]
•Click [ Next ]
•Click [ Accept ]
•Click [ Install ]
•Click [ Yes ]
•Click [ Restart Now ]

14
2.Audio
•Double click[ Setup ]
•Click [ Yes ]
•Click [ Next ]
•Click [ Yes, I want to restart my
computer now ], [ Finish ]

15
3.Graphics
•Double Click [ igxpin ]
•Click [ Yes ]
•Click [ Next ]
•Click [ Next ]
•Click [ Finish ]

16
4.Intel®ME
•Double Click [ SetupME ]
•Click [ Next ]
•Accept Terms then click [ Next ]
•Click [ Next ]
•Click [ Yes ]
•Click [ Finish ]

17
5.Serial IO
•Double Click [ SetupSerialIO ]
•Click [ Next ]
•Accept terms then click [ Next ]
•Click [ Next ]
•Click [ Next ]
•Select Yes, I want to restart this
computer now the click [ Finish ]