IBASE Technology ASB200-918 Series User manual

ASB200-918
Fanless System with
3.5” Disk-Size SBC System
User’s Manual
Version 1.0
(October 2020)

ii
ASB200-918 User Manual
Copyright
©2020 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

ASB200-918 User Manual
iii
Compliance
This product has passed CE tests for environmental specifications and limits, in
accordance with the directives of the Union European (EU). If users modify and/or
install other devices in this equipment, the CE conformity declaration may no longer
apply.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
ASB200-918 User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
Leave plenty of space around the device and do not block the openings for
ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO
THE VENTIILATION OPENINGS.
Slots and openings on the chassis are for ventilation. Do not block or cover these
openings. Make sure you leave plenty of space around the device for ventilation.
NEVER INSERT OBJECTS OF ANY KIND INTO THE VENTILATION
OPENINGS.
Use this product in environments with ambient temperatures -20˚C ~45˚C.
DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20˚C OR ABOVE 80˚C. This
could damage the device. The device must be used in a controlled environment.
Care for your IBASE products:
Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
Do not place heavy objects on the top of the device.
Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult your distributor or local
power company.
Do not walk on the power cord or allow anything to rest on it.
If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Disassembly,
modification, or any attempt at repair could generate hazards and cause damage to
the device, even bodily injury or property damage, and will void any warranty.

ASB200-918 User Manual
v
CAUTION
Danger of explosion if internal lithium-ion battery is replaced by an incorrect type.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Warranty Policy
IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, memory, HDD, power adapter, panel
and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAILS DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from your distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
Product model name
Product serial number
Detailed description of the problem
The error messages in text or in screenshots if there is any
The arrangement of the peripherals
Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi
ASB200-918 User Manual
Table of Contents
Chapter 1 General Information...................................................................1
1.1 Introduction.............................................................................................2
1.2 Features..................................................................................................2
1.3 Packing List ............................................................................................3
1.4 Optional Accessories ..............................................................................3
1.5 Specifications..........................................................................................4
1.6 Product View...........................................................................................6
1.7 Dimensions.............................................................................................8
Chapter 2 Hardware Configuration.........................................................9
2.1 Installations...........................................................................................10
2.1.1 HDD Installation......................................................................11
2.1.2 Memory Installation ................................................................12
2.1.3 Mini-PCIe Card Installation.....................................................12
2.1.4 WiFi / 3G / 4G Antenna Installation.........................................13
2.1.5 Side Bracket Installation.........................................................13
2.1.6 Pinout for COM Ports, DC Power & Digital I/O Connectors.....14
2.2 Setting the Jumpers..............................................................................15
2.3 Jumper & Connector Locations on Motherboard...................................16
2.4 Jumpers Quick Reference.....................................................................17
2.4.1 Clear CMOS Data (JP2).......................................................17
2.4.2 Clear ME Register (JP3) ......................................................18
2.4.3 eDP Panel Power Selection (JP4)........................................18
2.5 Connectors Quick Reference................................................................19
2.5.1 eDP Connector (CN2)..........................................................20
2.5.2 Audio Connector (J1) ...........................................................21
2.5.3 SATA HDD Power Connector (J5) .......................................21
2.5.4 Front Panel Connector (J6)..................................................22
2.5.5 USB 2.0 Connector (J7).......................................................23
2.5.6 Battery Connector (J10).......................................................23
2.5.7 DC Power Input Connector (J13) .........................................24
2.5.8 Digital I/O Connector (J16)...................................................24

ASB200-918 User Manual
vii
Chapter 3 Driver Installation .................................................................25
3.1 Introduction...........................................................................................26
3.2 AMD Ryzen™ V1000 Graphics Drivers.................................................26
3.3 AMD Ryzen™ R1000 Graphics Drivers.................................................28
3.4 HD Audio Driver Installation..................................................................30
3.5 LAN Driver Installation ..........................................................................31
3.6 Observer...............................................................................................34
Chapter 4 BIOS Setup............................................................................36
4.1 Introduction...........................................................................................37
4.2 BIOS Setup...........................................................................................37
4.3 Main Settings........................................................................................38
4.4 Advanced Settings................................................................................38
4.5 Chipset Settings....................................................................................49
4.6 Security Settings...................................................................................50
4.7 Boot Settings.........................................................................................51
4.8 Save & Exit ...........................................................................................52
Appendix ......................................................................................................53
A. I/O Port Address Map............................................................................54
B. Interrupt Request Lines (IRQ)...............................................................56
E. Digital I/O Sample Code........................................................................57
F. Watchdog Timer Configuration..............................................................61

viii
ASB200-918 User Manual
THIS PAGE IS INTENTIONALLY LEFT BLANK.

1
Chapter 1
General Information
The information provided in this chapter includes:
Features
Packing List
Optional Accessories
Specifications
Product View
Dimensions

2
ASB200-918 User Manual
1.1 Introduction
The ASB200-918 compact fanless system supports the AMD Ryzen™
Embedded V1000/R1000 SoC featuring Vega GPU for stunning 4K Ultra
High-Definition resolution and driving two HDMI (2.0a) graphics display. It
supports two SO-DIMM sockets supporting fast data transfers with up to
32GB DDR4-2400 memory and ECC for data integrity and flexible I/O
connectivity and expansion ports. The system comes with an operating
temperature range of 0°C to 45°C.
1.2 Features
Fanless system with IBASE IB918 3.5’’ Disk-Size SBC
AMD Ryzen™Embedded V1000 /R1000 on board
2x DDR4 SO-DIMM, Max. 32GB, supports ECC
Supports 2x M.2 sockets (E-Key / M-Key, NVMe)
2x HDMI(2.0a), 2x Intel® Gigabit LAN
4 x COM ports, External GPIO
4 x USB3.1, 1x USB2.0
12V~24V DC-in Power Input
Operating temperature 0°C~45°C (32°F~113°F)

General Information
ASB200-918 User Manual
3
1
1.3 Packing List
Your product package should include the items listed below. If any of the
items below is missing, contact the distributor or the dealer from whom you
purchased the product.
ASB200-918…………………………………………………………………x 1
3-Pin Terminal Block (for power)………………………………………….x 1
10-Pin Terminal Block (for GPIO connector)…………………………….x 1
Side Brackets………………………………………………………………..x 2
Screws for Side Brackets…………………………………………………..x 4
Screws for M key and E key M.2 ………………………………………….x 2
Adapter for ASB200-918……………………………………………………x 1
Power cord……………………………………………………………………x 1
1.4 Optional Accessories
IBASE provide optional accessories as follows. Please contact us or your
dealer if you need any.
WIFI / BT module Kit
DC Power Jack
Power Adapter and Power Cord (for DC power jack)

4
ASB200-918 User Manual
1.5 Specifications
Product Name
ASB200-
918-1605
ASB200-
918-1202
ASB200-
918-1606G
ASB200-
918-1505G
Motherboard
IB918F-1605
IB918F-1202
IB918F-1606G
IB918F-1505G
MB Form Factor
3.5” disk-size SBC
System
Operating
System
Windows 10
Linux Ubuntu / Fedora
AMD Embedded
Ryzen™SoC*
V1605B
V1202B
R1606G
R1505G
Memory
2x 8GB DDR4-2666 SO-DIMM
Expandable to 32 GB, ECC supported
Storage
1 x 2.5” HDD or SSD drive bay
Graphics
AMD V1000 series APU built-in Radeon Vega graphics
(V1605B Support Vega 8)
Power Supply
90W power adaptor (Optional)
Chassis
Aluminum & steel, black
Mounting
Desktop mount or Wall mount bracket
Dimensions
(W x H x D)
240mm (W) x 162mm (D) x 42mm (H)
Weight
1.8 kg (3.97 lb)
Certificate
CE / LVD / FCC Class B
AMD Embedded Ryzen™ SoC Supported:
AMD V1605B /QC/2.0GHz~3.6GHz/2MB L2 cache/12W~25W TDP
[C018RYZEG20010100P] For IB918F-1605
AMD V1202B /DC/2.3GHz~3.3GHz/1MB L2 cache/12W~25W TDP
[C018RYZEG23010100P] For IB988F-1202
AMD R1606G /DC/2.6GHz~3.5GHz/1MB L2 cache/12W~25W TDP
[C018RYZEG20010100P] For IB988F-1606G
AMD R1505G /DC/2GHz~3.3GHz/1MB L2 cache/12W~25W TDP
[C018RYZEG23010100P] For IB988F-1505G

General Information
ASB200-918 User Manual
5
1
I/O Interface
Front Panel I/O
- 1 x Power button/RST/HDD/On/Off
- 2 x Antenna holes
- 1 x Audio Jack for Line-out/Line-in/Mic-in
- 3 x DB9 for COM#2~#4 (RS232 only)
- 1 x USB port 2.0/3.0
Rear Panel I/O
- 1 x 3-pin terminal block connector for external digital I/O
- 1x GPIO (4-in/4-out)
- 1 x DB9 for COM#1 (RS232/422/485),
- 2 x RJ-45 GbE Connector
- 2 x HDMI
- 2 x Antenna holes
Storage
- 1 x M.2 128GB TLC Toshiba
- 1 x 2.5’’ SSD;2.5" SATA3 64G TLC 7mm [PHISON
SSBP064GTB3C0-S11] (Default)
Environmental
Operating
Temperature
0°C~45°C (32°F~113°F)
Storage
Temperature
-20°C~80°C (-4°F~176°F)
Humidity
5%~90%@45°C (non-condensing)
Vibration
Operating : 3Grms / 5~500Hz
Shock
Operating : 20G / 11ms
Non-operating : 40G / 11ms
All specifications are subject to change without prior notice.

6
ASB200-918 User Manual
1.6 Product View
Front View
No.
Name
No.
Name
1
PWR LED Indicator
5
Audio Jacks
(From left to right: Mic-In,
Line-In, Lin-Out)
2
HDD LED Indicator
6
USB 3.0 (ASB200-918-1605 &
ASB200-918-1202 only )
USB 2.0 (ASB200-918-1606 &
ASB200-918-1505 only )
3
Power Button
7
COM2 ~ COM4 Ports
(COM2 ~ COM4: RS-232)
4
Reset Button
8
2 Antenna Holes

General Information
ASB200-918 User Manual
7
1
Rear View
No.
Name
No.
Name
1
DC-In Power Connector
5
HDMI Port
2
Digital I/O Connector
(4-In / 4-Out)
6
USB 3.0 Ports
3
COM1
(COM1: RS-232/422/485)
7
2 Antenna Holes
4
GbE LAN Ports
Oblique View

8
ASB200-918 User Manual
1.7 Dimensions
Unit: mm

9
Chapter 2
Hardware Configuration
The information provided in this chapter includes:
Installations
Information and locations of connectors

10
ASB200-918 User Manual
2.1 Installations
Before installations, you need to remove the bottom chassis cover by
loosening the screws shown below.
After removing the above screws, remove the bottom chassis cover.

Hardware Configuration
ASB200-918 User Manual
11
2
2.1.1 HDD Installation
If you need to install or replace an SSD or a HDD, remove the single screw
shown below to remove the tray, and then loosen the four screws. Attach the
SSD / HDD and tighten these screws.
Remove the single screw holding the tray.
Remove the four screws holding the HDD/SSD.

12
ASB200-918 User Manual
2.1.2 Memory Installation
If you need to install or replace a memory module, perform the following
steps:
1. Locate the memory slot on the board.
2. Align the key of the memory module with that on the memory slot and
insert the module slantwise.
3. Gently push the module down in an upright position until the clips of the
slot close to hold the module in place when the module touches the
bottom of the slot.
To remove the module, press the clips outwards with both hands, and the
module will pop-up.
2.1.3 Mini-PCIe Card Installation
If you need to use a mini-PCIe card for expansion slots, follow the instructions
below for installation after you remove the device bottom chassis cover.
1. Align the key of the mini-PCIe card to the mini-PCIe interface, and insert
the card slantwise.
2. Push the mini-PCIe card down, fix it onto the standoff with a screw.