3One data IAC8500-1GC4GT User manual

IAC8500-1GC4GT
Industrial Wireless Controller
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Tel : [phone]
Fax: [phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the wireless controller.
1
Wireless controller x1
2
Mounting lug x2
3
Power line x2
4
Warranty card
5
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it asap.
【Product Overview】
The product is industrial wireless controller with high stability
and cost-effectiveness. The model is
IAC8500-1GC4GT-2P110_240VAC (1 Gigabit Combo WAN
port + 4 Gigabit RJ45 LAN ports, dual power supply
110~240VAC).
【Panel Design】
Front View
Rear View
1. Gigabit LAN port
2. Gigabit LAN port status indicator
3. Gigabit Combo WAN port (RJ45 or SFP)
4. Gigabit Combo WAN port status indicator
5. Console port (Reserved)
6. USB3.0
7. USB2.0
8. Relay output terminal
9. RESET restoring factory setting button
10. Device running indicator RUN
11. Device power supply status indicator PWR1/PWR2
12. Relay alarm indicator ALM
13. Lugs
14. AC power input outlet
15. Grounding screw
【Mounting Dimension】
Unit: mm
Note before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Rack-mounted】
Step 1 Select the device mounting location to ensure
enough size.
Step 2 Adopt bolts to install the mounting lugs in the
device position as figure below.

Step 3 Place the device on the rack surface plate; adopt 4
screws to mount the right and left mounting lugs on
the rack.
Step 4 Check and confirm the product is mounted firmly on
the rack, mounting ends.
【Disassembling Device】
Step 1 Device power off.
Step 2 Unscrew the fixed mounting lug screw on the rack.
Step 3 Shift out the device from rack, disassembling ends.
Note before powering on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First, remove the power plug,
and then remove the wiring section of terminal block.
Please pay attention to the above operation sequence.
【Power Supply Connection】
This device provides 2 AC power supply inputs, and supports
power supply redundancy. When one of the power supplies
fails, the device can still operate normally.
The power supply input range is 110~240VAC, 50~60Hz.
【Restore factory defaults】
RESET is restoring default settings button. Restoring default
settings steps as follows: Press and hold the RESET button
for 5s then release it, the device would restore the factory
settings automatically.
【Relay Connection】
Relay terminals are a set of normally open contacts of the
device alarm relay. They are open circuit in the state of normal
non alarm, closed when any alarm information occurs. For
example, they are closed when powered off, and send out
alarm. The product supports 1 relay alarm information output,
which can be connected to alarm light or alarm buzzer or
other switching value collecting devices; it can timely inform
operators when the alarm occurs.
【Console Port Connection】
The series products provide 1 program debugging
port based on RS-232 serial port which can
conduct device CLI command management after
connecting to PC. The interface adopts RJ45 port,
the RJ45 pin definition as follows:
No.
2
3
5.
PIN
TXD
RXD
GND
【USB Port Connection】
This device provides 1 USB2.0 interface and 1 USB3.0
interface, both of which are USB Type A female head
interfaces. USB2.0 interface is black. USB3.0 interface is blue,
and it can be backward-compatible with USB2.0.
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
PWR1/PWR2 ON Power supply PWR1/PWR2 is
connected and running
normally
OFF
Power supply PWR1/PWR2 is
disconnected or running
abnormally
ALM
ON
Power supply link has alarm
OFF Dual power supply link have
no alarm
RUN
ON The device is powered on or
the device is abnormal.
OFF The device is powered off or
the device is abnormal.
Blinking
Blinking 1 time per second,
system is running well.
Link/Act
(G1-G4,
WAN)
ON
The Ethernet interface has
established an active network
connection.
Blinking The Ethernet interface is in a
network activity state.
OFF
Ethernet port has not
established valid network
connection
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via LAN. The way of logging
in to device’s configuration interface via IE browser is shown
as below:
Step 1 Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Step 2 Enter device’s IP address in the address bar of the
computer browser.
Step 3 Enter device’s user name and password in the
login window as shown below.

Step 4 Click “Login” button to login to the WEB interface of
the device.
Description:
The default IP address of the device is “192.168.3.1”.
The default user name and password of the device is
“admin”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit LAN port 10/100/1000 Base-T(X)
self-
adapting RJ45 port, half/full
duplex self-
adaption support
MDI/MDI-X self-adaption
Gigabit WAN port
Gigabit Combo, optional
10/100/1000Base-
T(X) and
1000Base-X SFP
Console Port
CLI command line management
port (RS-232), RJ45(CLI function
is reserved)
USB 2.0 port
USB Type A female head
USB 3.0 port
USB Type A female head
Alarm interface 2-pin 7.62mm pitch terminal block,
support 1 relay alarm output
Indicator
Power supply indicator, alarm
indicator, running indicator,
interface indicator
Power supply
Input power supply 110~240VAC 50-60Hz
Dual power supply redundancy,
3A over-current protection
Access terminal
block
Power supply outlet with switch
Power consumption
No-load
3.0W@220VAC
Full-load
5.0W@220VAC
Working
environment
Working temperature
-40~75
℃
Storage temperature
-40~85
℃
Working humidity
5%
～
95% (no condensation)
Protection grade
IP30(metal)