3One data ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 User manual

1 / 5
ICPE2300A-BW-8A25-1GC3GT-PD2P12_48
Industrial Indoor
5G Wireless Router
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Tel : [phone]
Fax: [phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the device for the first time.
1.
5G Router x1
2.
2.4G omnidirectional antenna x2
3.
5.8G omnidirectional antenna interface x2
4.
5G Sub-6G antenna x4
5.
Magnetic sucker base and connecting line x8
6.
SFP slot dust cap x1
7.
DIN-Rail mounting attachment x1
8.
Ejection pin for SIM card
9.
Warranty card
10.
Certificate
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This product is DIN-Rail Industrial-grade Indoor 5G Wireless
Router. Model: ICPE2300A-BW-8A25-1GC3GT-PD2P12_48
(1 Gigabit COMBO port(PoE WAN) + 3 Gigabit copper ports
(LAN) + 2 2.4G antennas + 2 5.8G antennas + 4 5G Sub-6G
antennas, 12~48VDC single power and dual input).
【Panel Design】
Front view
Top view
Rear View
1. System indicators, from left to right in turn they are:
Running Indicator(RUN)
Alarm Indicator(ALM)
Power Supply Indicator(P1-P2)
2. WiFi Indicators, from left to right in turn they are:
2.4G wireless signal indicator (2.4G)
5.8G wireless signal indicator (5.8G)

2 / 5
2.4G/5.8G bridge signal strength indicator ( )
3. 10/100/1000Base-T(X) Gigabit copper port
(LAN1-LAN3)
4. 10/100/1000Base-T(X) Gigabit PoE copper port
and 1000Base-X Gigabit SFP combo port(WAN)
5. Ethernet port indicators, from top to bottom in turn
they are:
Gigabit copper port indicator (LAN1-LAN3)
PoE indicator (PoE)
Gigabit COMBO port indicator(WAN)
6. RESET button
7. CONSOLE port
8. 5G indicators, from left to right in turn they are:
5G NR indicator(5G)
5G NR bridge signal strength indicator ( )
9. USB, SD, SIM indicators, from left to right in turn
they are:
USB interface indicator(USB)
SD card indicator(SD)
SIM card indicator(SIM1-SIM2)
10. USB interface(USB)
11. SD/SIM card slot(SIM)
12. Terminal blocks for power1 input (V1)
13. Terminal blocks for power2 input (V2)
14. Relay output alarm(RELAY)
15. 5.8G antenna interface(5.8G)
16. 2.4G antenna interface(2.4G)
17. 5G Sub-6G antenna interface(5G)
18. Grounding screw
19. DIN-Rail mounting kit
【Mounting Dimension】
Unit: mm
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
The product adopts 35mm standard DIN-Rail mounting which
is suitable for most industrial scenes, mounting steps as
follows:
Step 1 Check if the DIN-Rail mounting kit is installed firmly.
Step 2 Clip the upper part of the DIN-Rail mounting kit, i.e.
the fixed side, into the DIN rail.
Step 3 Press the lower side of the device and insert the
lower part of DIN-Rail mounting kit (the side with
spring support) into DIN-Rail.
Tips:
The DIN-Rail spring support is a metal sheet that can
move up and down, and there will be a sound after it is
clamped in.
Step 4 Check and confirm the product is firmly installed on
DIN rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1 Power off the device.
Step 2 Use a slot type screwdriver or other tools to move the
DIN rail spring support downward; At the same time,
move the lower side of the device outward and move
out the lower part of the DIN rail mounting kit.
Step 3 Lift the device upward slightly, move out the upper
part of DIN-Rail mounting kit. Disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,

3 / 5
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
PoE power supply
The WAN port of this device supports PoE power receiving,
which conforms to IEEE802.3af/at standard.
12~48VDC power supply
The device provides 6-pin 5.08mm pitch power
supply terminal blocks and power supply
occupies the top 4 pins. It supports two
independent DC power inputs, V1 and V2. The
device supports redundant power supply, two
independent power supplies can work at the
same time. The device will still run non-stop when one power
supply fails. The power supply supports non-polarity
connection, and the equipment can still work normally after
reverse connection. The definitions of power pin are shown in
the left figure, and the power input range is 12~48VDC.
【Relay Connection】
This device provides 6-pin 5.08mm pitch terminal
blocks, relay occupies the lower 2 pins. Relay
terminals are a set of normally open contacts of
the device alarm relay. They are open circuit in
the state of normal non alarm, closed when any
alarm information occurs. The relay can
externally connect to alarm lights or alarm buzzer or other
switching value collecting device in order to timely notify
operators when the alarm occurs. (This function is reserved).
【Reset Button Setting】
The device provides 1 RESET button, press the
RESET button for 1~2s and release it, and the device
will restart automatically; Press and hold the RESET
button for 5s and release it, and the device will automatically
restore the factory defaults.
【Console Port Connection】
The device provides 1 program debugging port based on
RS-232 serial port which can conduct device CLI command
management after connecting to PC. The interface adopts
RJ45 port, the RJ45 pin definition is as follows:
Pin No.
2
3
5
Definition
TXD
RXD
GND
【USB Port Connection】
This device provides 1 Type-A USB 2.0 Female,
this interface is reserved.
【Mounting SIM Card】
This device supports 1 SIM card slot which can
insert 1 Micro SIM card and 1 Nano SIM card , 1
Micro-SD card, in which SD card is reserved.
Notice:
If the SIM card needs to be changed, the device should
be power off first in case of damaging the card.
【Antenna Connection】
The antenna specifications provided by the device are shown
below:
Type P/N
Gain
(dBi)
Quantity
(pcs)
2.4G wireless
3005040101
5
2
5.8G antenna 3005040102 5 2
5G Antenna
3005040098
3
4
Magnetic sucker base
3005040090
—
4
Magnetic base with sucker
3005040115
—
4
【Checking LED Indicator】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate
Description
RUN ON
The device is powering on or the
device is abnormal.
Blinking
The device is running normally
LED
Indicate
Description
OFF
The device is powered off or the
device is abnormal.
ALM
ON
Device restore factory setting alarm
OFF
Without device alarm
P1-P2
ON
Power P1/P2 is running normally
OFF
Power P1/P2 is disconnected or
running abnormally
2.4G/
5.8G
ON
Wireless WiFi network is enabled
Blinking
Wireless WiFi is in an active
network status
OFF
Wireless WiFi network is running
abnormally or turned off
The indicators are all off, indicating
that no 2.4G/5.8G bridge has been
established.
One indicator is on. It means
2.4G/5.8G signal at the opposite
end is weak
All indicators are on. It means
2.4G/5.8G signal at the opposite
end is strong
LAN1-
LAN3
/WAN
ON
LAN/WAN port connection has
established a valid network
connection
Blinking LAN/WAN port is in network active
status
OFF
LAN/WAN port connection has not
established a valid network
connection
PoE
ON
PoE power input in WAN port is
normal.
OFF WAN port has no PoE power input
or is receiving power abnormally
5G
ON
5G network is enabled
Blinking 5G network is in an active network
status
OFF
5G network is running abnormally

4 / 5
LED
Indicate
Description
or turned off
The indicators are all off, indicating
that no 5G/4G bridge has been
established.
One indicator is on. It means 5G/4G
signal at the opposite end is weak
Two indicators are on. It means
5G/4G signal at the opposite end is
normal
All indicators are on. It means
5G/4G signal at the opposite end is
strong
USB
ON
USB interface has been connected
OFF
USB interface has not been
connected
SD
OFF
Reserved
SIM1-
SIM2
ON SIM1/SIM2 card is enabled or has
dialed successfully
OFF
SIM1/SIM2 card is disabled or
installed abnormally
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access LAN port of the device via Ethernet
interface. The way of logging in to device’s configuration
interface via IE browser is shown as below:
Step 1 Configure the IP addresses of computer and the
device’s LAN port to the same network segment, and the
network between them can be mutually accessed
Step 2 Enter device’s IP address in the address bar of the
computer browser.
Step 3 Enter device’s username and password in the login
window as shown below.
Step 4 Click “Login” button to login to the WEB interface of
the device.
Note:
The default IP address of the device’s LAN port is
“192.168.1.254”.
The default user name and password of the device are
“admin”.
If the user name or password is lost, user can restore it
to factory settings via restoring factory setting button;
all modified configurations will be cleared after
restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit
copper port
(LAN)
3 10/100/1000Base-T(X) self-adaptive
RJ45 LAN ports, support automatic flow
control, full/half duplex mode,
MDI/MDI-X self-adaption
Gigabit
COMBO
indicator
(WAN)
1 10/100/1000Base-T(X) self-adapting
RJ45 port or 1000 Base-X SFP slot, it’s
WAN port by default; The copper port
supports automatic flow control, full/half
duplex, MDI/MDI-X self-
adaptation, and
support PoE power receiving
Antenna
interface

2 2.4G antenna interfaces,
RP-SMA-K(Female);

2 5.8G antenna interfaces,
RP-SMA-K(Female);
4 5G Sub-
6G antenna interfaces,
SMA-K(Female);
USB
interface
1 Type-A USB 2.0 Female, this interface
is reserved
SIM card slot 1 Micro SIM card and 1 Nano SIM card,
redundant backup; 1 Micro-
SD card is
reserved
Console port
CLI command line management port
(RS-232), RJ45
Alarm
interface
6-pin 5.08mm pitch terminal blocks (2-pin
for relay), support 1 relay alarm output,
this interface is reserved
Indicator Running indicator, alarm indicator, power
indicator, 2.4G indicator, 5.8G indicator,
Wireless bridge signal strength indicator,
interface indicator, PoE indicator, 5G
indicator, 5G bridge signal strength
indicator, USB indicator, SD card
indicator, SIM card indicator
WiFi Radio Frequency
802.11b/g/n
2.412GHz~2.4835GHz
802.11ac/n/a
5.18GHz-5.825GHz
RF power
output
20dBm
Modulation
system
DBPSK,DQPSK,CCK,OFDM,16-QAM,64
-QAM,256-QAM
WiFi Receiving Sensitivity
802.11n_HT
40
-82dBm@MCS0,-64dBm@MCS7
802.11n_HT
20
-85dBm@MCS0,-67dBm@MCS7
802.11g/a
-91dBm@6Mbps,-72dBm@54Mbps

5 / 5
802.11b
-93dBm@1Mbps,-87dBm@11Mbps
802.11ac
-84dBm@MCS0,-59dBm@MCS9
WiFi Transmitting Power
802.11n_HT
40
23dBm@MCS0,20dBm@MCS7
802.11n_HT
20
23dBm@MCS0,20dBm@MCS7
802.11g/a
23dBm@6Mbps,20dBm@54Mbps
802.11b
23dBm@1Mbps,20dBm@11Mbps
802.11ac
23dBm@MCS0,20dBm@MCS9
5G Operating Frequency Band
5G NR n1/n2/n3/n5/n7/n8/n12/n20/n28/n38/n40/
n41/n48/n66/n71/n77/n78/n79
4G LTE-FDD
B1/B2/B3/B4/B5/B7/B8/B9/B12/B13/B14/
B17/B18/B19/B20/B25/B26/B28/B29/B30
/B32/B66/B71
4G LTE-TDD
B34/B38/39/B40/B41/B42/B48
3G WCDMA
B1/B2/B3/B4/B5/B6/B8/B19
5G Bandwidth (downstream, upstream)
5G SA
DL 2.1Gbps;UL 900Mbps
5G NSA
DL 2.5Gbps;UL 650Mbps
LTE
DL 1Gbps;UL 200Mbps
WCDMA
DL 42Mbps;UL 5.76Mbps
Power Supply
Input power
supply

WAN port: supports PoE power
receiving, which conforms to
IEEE802.3af/at standard

power supply terminal: supports
12~48VDC single power and dual
power input, supports input
redundancy and nonpolarity,
adopting 6-
pin 5.08mm pitch
terminal block(4-pin power supply)
Power Consumption
No-load
6.5W@24VDC
Full-load
20.0W@24VDC
Working Environment
Working
temperature
-40~75℃
Storage
temperature
-40~85℃
Working
humidity
5%～95%(no condensation)
Protection
grade
IP40 (metal shell)