3One data IES615-2D Series User manual

- 1 -
IES615-2D Series
Industrial Ethernet Switch
User Manual
Shenzhen 3onedata Technology o., Ltd.
Tel: [phone] Fax: [phone]
www.3onedata.com
 Summarize 
IES615-2D erie i an integrated erial erver function of the
managed indu trial Ethernet witche . The indu trial Ethernet
witch con i t of 5 Fa t Ethernet port and 2 erial port (RS-232
or RS-485/422). Support Fa t Ethernet copper port and optical
fiber port option. It adopted SW-RingTM redundant technology
(Recovery time<20m ), u er can et the redundant ea ily to
increa e network reliability, furthermore. It adopted no fan, low
power con umption de ign, IP30, corrugate high trength iron
hell, the performance i more teadily. It accorded with CE, FCC
tandard and indu trial grade de ign, DIN rail in tallation and
wide operating temperature (-40~75

), it can ati fied ome
kind of indu trial environment, it can provide reliable and
quickly olution for your Ethernet device.
 Packing list 
The indu trial Ethernet witch i hipped with the following item .
If any of the e item are mi ing or damaged, plea e contact your
cu tomer ervice repre entative for a i tance.
Indu trial Ethernet witch

1
Documentation and oftware CD

1
U er manual

1
DIN-Rail mounting kit

1
Warranty card

1
 Features 
IEEE802.3, IEEE802.3u, IEEE 802.3x, IEEE802.1D/W
Support SW-RingTM redundant network patent technology
(Faulty recovery time<20m )
Support 2 port RS-232 or RS-485/RS-422 erial device
erver
Support ba ed on ocket application acce
Support TCP Sever, TCP Client and UDP ba ed mode; TCP
Sever and UDP advanced mode
Support RS-485 power and ignal i olation AC2500V
Support RSTP, IGMP, port trunking and port mirroring
Support Web, SNMP management
Support 2K MAC addre table
Support 2 power upply input and 1 relay alarm output
Support QOS, 802.1Q VLAN
High trength iron hell, IP30 protection
Indu trial grade de ign
Redundant 24VDC power upply input (12~48VDC)
-40~75

working temperature
DIN-rail, wall mounting in tallation
 Panel layout 
Vertical view and bottom view Rear view
Front panel view

- 2 -
1. Power input terminal block
2. Ground crew
3. 2-pin terminal block for relay output
4. DIP witche for default factory
5. Screw hole for Wall Mounting Kit
6. DIN-Rail mounting kit
7. Sy tem running LED
8. Link/ACT LED
9. Power indicator (PWR1, PWE2)
10. Serial port tran mit and receive data LED
11. RS-232 erial port (DB9M)
12. 10Ba e-T /100Ba e-TX Ethernet port
13. 100Ba e-FX fiber port
14. RS-485/422 erial port (5 bit terminal block)
 Power supply input 
The witch have redundant power input, provide one terminal
block (4 bit ) for PWR1 and PWR2 input. The redundant power
can be u ed ingle and u ed two elf-governed power to upply to
the y tem, PWR1 and PWR2 input at the ame time, when
neither of the e two power fail , the other power act a a
backup, and automatically upplie power need , en ure running
Ethernet rea uring. Voltage input range i 12

48VDC (terminal
block defined a : V1-

V1+

V2-

V2+).
 Dimension 
The erie of witche are the ame ize, and the number of the
Ethernet interface i different. Unit (mm)
 DIP Switch 
Top panel provided 4 bit DIP witch to do function configure

OFF i default factory

,1 and 2 keep for future function. 3 i
AT mode. 4 i recovery default factory. Plea e power off and
power on when you change the tatu of DIP witch.
 Relay connection 
The relay own two contact of the terminal block on the top
panel of the Switch erie . It i u ed to detect both power failure
and port failure. The open circuit tate in normal non alarm tate,
when there i any alarm information to the clo ed tate. The relay
can external alarm light or alarm buzzer or external witch ignal
acqui ition device in order to timely notify operator when an
alarm occur .
 onsole port 
Thi erie product provided 1pc procedure te t port ba ed in
erial port. It adopt RJ45 interface, located in top panel, can
configure the CLI command through RJ45 to DB9 female cable.
 ommunication connector 
10/100BaseT(X) Ethernet port
The pinout define of RJ45 port di play a below, connect by UTP
or STP. The connect di tance i no more than 100m. 100Mbp i
u ed 120

of UTP 5, 10Mbp i u ed 120

of UTP 3 ,4, 5.
RJ 45 port upport automatic MDI/MDI-X operation. can
connect the PC, Server, Converter and HUB .Pin 1,2,3,6
Corre ponding connection in MDI. 1→3, 2→6, 3→1, 6→2 are
u ed a cro wiring in the MDI-X port of Converter and HUB.
10Ba e-T/100Ba e-TX are u ed in MDI/MDI-X, the define of Pin
in the table a below.
1 8

- 3 -
NO. MDI ignal MDI-X ignal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
6 RX- TX-
4, 5, 7, 8
 
Note
 
TX
 
Tran mit Data
  
RX
 
Receive Data
    
Not u e.
10/100Base-T(X) MDI (straight-through cable)
10/100Base-T(X) MDI-X ( ross over cable)
MDI/MDI-X auto connection make witch ea y to u e for
cu tomer without con idering the type of network cable.
100Base-FX Fiber port
100Ba e-FX full-duplex SM or MM port, SC/ST/FC type .The
fiber port mu t be u ed in pair, TX (tran mit) port connect remote
witch’ RX (receive) port; RX (receive) port connect remote
witch’ TX (tran mit) port.
The optical fiber connection upport the line to in truct
enhance the reliability of network effectively.
Suppose: If you make your own cable, we ugge t labeling the
two ide of the ame line with the ame letter (A-to-A and B-to-B,
hown a below, or A1-to-A2 and B1-to-B2).
RS-232 port 
PIN RS-232
1 DCD
2 RxD
3 TxD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
RS-485/422 port:
PIN RS-422 RS-485
1 T+ D+
2 T- D-
3 GND GND
4 R+ /
5 R- /
 LED Indicator 
LED indictor light on the front panel of product, the function of
each LED i de cribed in the table a below.
System indication LED
LED State Description
PWR1
ON Power i being upplied to power
input PWR1
OFF Power i not being upplied to
power input PWR1
PWR2
ON Power i being upplied to power
input PWR2
OFF Power i not being upplied to
power input PWR2
Run
ON/OFF Sy tem i not running well
Blinking Sy tem i running well
Link/A T
(1~5)
ON Port connection i active
Blinking Data tran mitted
OFF Port connection i not active
TX

1~2

Blinking Tran mit data unwonted
OFF Tran mit data wonted
RX

1~2

Blinking Receive data unwonted
OFF Receive data wonted
 Installation 
Before in tallation, confirm that the work environment meet the
in tallation require, including the power need and abundant
pace. Whether it i clo e to the connection equipment and other
equipment are prepared or not.
1. Avoid in the un hine, keep away from the heat fountainhead or
the area where in inten e EMI.
2. Examine the cable and plug that in tallation requirement .
3. Examine whether the cable be eemly or not (le than 100m)
according to rea onable cheme.
12345
DB9 Male
1 2 3 4
5
6 7 8
9

- 4 -
4. Power: Redundant, dual 12-48VDC power input
5. Environment

working temperature: -40

75

Storage Temperature: -40

85

Relative humidity 5%

95%
DIN Rail Installation
In order to u e in indu trial environment expediently, the witch
adopt 35mm DIN-Rail in tallation, the in tallation tep a below:
1. Examine the DIN-Rail attachment
2. Examine DIN-Rail whether be firm and the po ition i
uitability or not.
3. In ert the top of the DIN-Rail into the lot ju t below the
tiff metal pring.
4. The DIN-Rail attachment unit will nap into place a hown
below.
Wiring Requirements
Cable laying need to meet the following requirement ,
1. It i needed to check whether the type, quantity and
pecification of cable match the requirement before cable
laying;
2. It i needed to check the cable i damaged or not, factory
record and quality a urance booklet before cable laying;
3. The required cable pecification, quantity, direction and
laying po ition need to match con truction requirement , and
cable length depend on actual po ition;
4. All the cable cannot have break-down and terminal in the
middle;
5. Cable hould be traight in the hallway and turning;
6. Cable hould be traight in the groove, and cannot beyond the
groove in ca e of holding back the inlet and outlet hole .
Cable hould be banded and fixed when they are out of the
groove;
7. U er cable hould be eparated from the power line . Cable ,
power line and grounding line cannot be overlapped and
mixed when they are in the ame groove road. When cable i
too long, it cannot hold down other cable, but tructure in the
middle of alignment rack;
8. Pigtail cannot be tied and werved a le a po ible.
Swerving radiu cannot be too mall ( mall werving cau e
terrible lo of link). It banding hould be moderate, not too
tight, and hould be eparated from other cable ;
9. It hould have corre ponding imple ignal at both ide of the
cable for maintaining.
 Specification 
Technology
Standard: Support IEEE802.3, IEEE802.3u, IEEE802.3x,
IEEE802.1Q, IEEE802.1p, IEEE802.1D/W
Protocol: ARP, ICMP, TCP, UDP, DHCP, DNS, HTTP, SW-Ring,
RSTP, SNMP
Flow control: IEEE802.3x, back pre ure control
Function
Switch function: SW-Ring, QOS, 802.1QVLAN, RSTP, SNMP,
Port trunking, tatic multica t filter, port mirroring, port
flow tati tic , upgrade online, up and download
configuration file, u er name acce y tem
SW-Ring: Support Single, Couple, Chain, Dual homing
Exchange attribute
100M forward peed: 148810pp
Tran mit mode: tore and forward
Switching fabric capacity: 1.0Gbp
MAC addre table: 2K
Memory: 1Mbit
Interface
Electric port: 10Ba e-T/100Ba e-TX auto peed control, Half/full
duplex and MDI/MDI-X auto detect
100M optic fiber port: 100Ba e-FX, SC/ST/FC connector
Alarm port: 2 bit 7.62mm terminal block,
1 channel relay alarm output
Serial Port: RS-232 (DB9 male) or RS-485/422 (terminal block)
Serial
RS-232 ignal: DCD, RXD, TXD, RTS, CTS, DTR, DSR, GND,
RI
RS-485 ignal: D+, D-, GND
RS-422 ignal: T+, T-, GND, R+, R-
Parity: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate; 300

115200bp
RS-232 connector: DB9 male
RS-485 connector: 5 bit terminal block
RS-485/422 power i olation and ignal i olation: AC2500V
Transfer distance
Twi ted cable: 100M ( tandard CAT5/CAT5e cable)
Multi-mode: 1310nm, 2Km
Single-mode: 1310nm, 20/40/60Km
1550nm, 80/100/120Km
RS-485/422: 1200m
RS-232: 15m
LED indicator
Run indicator: Run
Power upply indicator: PWR1, PWR2
Ethernet interface indicator: Link (1~5)
Serial port indicator: Tx (1~2), Rx (1~2)
Power supply
Input voltage: 12

48VDC
Type of input: 4 bit 7.62mm pitch terminal block

- 5 -
Over-current protection: 4.0A
RS-485 power i olation and ignal i olation: AC2500V
onsumption
 IES615-1F-2D (RS-232):
Unload con umption: 1.8W@24VDC
Full load con umption: 2.4W@24VDC
 IES615-1F-2DI (RS-485):
Unload con umption: 2.1W@24VDC
Full load con umption: 2.6W@24VDC
 IES615-2F-2D (RS-232):
Unload con umption: 2.5W@24VDC
Full load con umption: 3.0W@24VDC
 IES615-2F-2DI (RS-485):
Unload con umption: 3.0W@24VDC
Full load con umption: 3.5W@24VDC
Working environment
Working temperature: -40

75

Storage temperature: -40

85

Relative Humidity: 5%~95% (no conden ation)
Mechanical Structure
Shell: IP30 protect grade, metal hell
In tallation: DIN-Rail mounting
Weight: 900g
Size (W×H×D): 53mm×105mm×136mm
Industry Standard
EMI: FCC Part 15, CISPR (EN55022) cla A
EMS: EN61000-4-2 (ESD), Level 4
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 4
EN61000-4-5 (Surge), Level 4
EN61000-4-6 (CS), Level 3
EN61000-4-8, Level 5
Shock: IEC 60068-2-27
Free fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
ertification
CE, FCC, RoHS, UL508 (Pending)
Warranty: 5 year