4iiii PM100 User manual

Quick Start Guide
For a complete User Manual go to 4iiii.com/precision
3
Reinstall
crank and pedals on your
bike and tighten to specs
Wake-up
PRECISION by rotating
the crank a few times
2
Getting Started!
Ensure that battery, o-ring and cap lid
are functional and secure!
These pieces are critical to giving you a
water and dust tight seal and must be
rmly in place!
Positive side faces into the cap. Attach
the cap to your PRECISION pod.
1
Load Battery into Cap
Cap
First ride: Follow all steps. Next rides: Wake up, Zero and Ride.
FCC Compliance Statement
FCC ID: ZZNPM100
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device maynot cause har mful interference,
and (2) this device must accept any interference received, including interference that maycause undesired operation.
The grantee is not responsible for any changes or modications not expressly approvedby the par ty responsible forcompliance. Such modications could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guaranteethat inter ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an expereince radio/TV technician for help.
Industry Canada (IC) Compliance Statement
IC: 9896A-PM100
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesiredoperation of the device. CAN
ICES-3(B)/NMB-3(B)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareildoit accepter tout brouillage radioélectrique reçu, même
si ce brouillage est susceptible d’en compromettre le fonctionnement du dispositf. CAN ICES-3(B)/NMB-3(B)
Le dispositif rencontre l’exemption des des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition et la conformitéde r f.
Cet émetteur ne doit pas être co-placé ni fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipment devrait être installé et
actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
Made in Canada by:
Contact us at
[email protected]
20301_D1
2032 Battery

Ride with Heart Rate
Viiiiva Chest Strap Heart Rate Monitor also bridges ANT+
to Bluetooth Smart. 4iiii.com/Viiiiva
Ride in Your Zone
Sportiiii Heads-up Display syncs with PRECISION and
keeps you on target. 4iiii.com/Sportiiii
Pair PRECISION
with power-capable
devices
Zero
PRECISION using paired device.
Unclip pedals and position crank arms.
(as shown below)
Press “zero
oset” or
“calibrate” on
your display
Ride
1-4 minutes to warm up
PRECISION
5
4
Ride With PRECISION
Data is automatically pushed to
your paired device through ANT+
or BLE.
Syncing
Data...
234W
1:40:23
97RPM
35k m/h
234W
1:40:23
View post-ride performance
analysis using your favorite app.
Upload Data
from Device
6
Left
crank
Right
crank
For best results avoid temperature swings between steps 5 and 6