70mai WT1004 User manual

70mai Saphir Watch User Manual

Contents
English ………………………………………………………………………………
日本語 ………………………………………………………………………………
繁體中文 ……………………………………………………………………………
Español ………………………………………………………………………………
Русский ……………………………………………………………………………
Deutsche ……………………………………………………………………………
Français ……………………………………………………………………………
Italiano ………………………………………………………………………………
Português……………………………………………………………………………
1
15
26
37
49
60
72
84
96

Note: Illustrations of product, accessories, and user interface in the user manual are for reference
purposes only. The actual product and functions may vary due to product enhancements.
1. Upper Button
2. Display Screen
3. Lower Button
Read this manual carefully before use, and retain it for future reference.
Product Overview
Charging Accessory
USB Connector
2
1
3
4
5
6
7
Watch
4. Microphone 5. Heart Rate Sensor Area
6. Contact Point
7. Barometer
1

Download and install the 70mai Health app to better manage your watch, and log in to
your 70mai Health account for more services.
1. Press and hold the upper button for 3 seconds to turn on the watch. Scan the QR
code on the display screen with your phone, then download and install the 70mai
Health app.
You can also download and install the app from the app stores, or scan the QR code
below.
Note: The version of the app might have been updated, please follow the instructions based on the
current app version.
2. Log into your 70mai Health account in the app, select Add device and follow the
instructions to add your watch.
3. Allow the pairing request on the watch then wait until Paired successfully is
displayed on the app, the pairing process is completed.
Notes:
●During pairing, make sure the Bluetooth is enabled on your phone and the watch is well connected
with your phone.
●If you cannot find the watch while adding a device, or cannot connect with the watch during use,
please press and hold the upper button for 3 seconds to restore factory settings, then try again.
How to Connect
2

How to Use
Screen Instructions
View notifications: Swipe down from the top on
the home screen
Open control panel: Swipe up from the bottom
on the home screen
Switch widget: Swipe left or right on the home
screen
Go back: Swipe from the left edge to the right
on other pages
1
2
3
4
Press and hold for 1 second to wake Amazon
Alexa.
Press and hold for 3 seconds to turn on/off.
Press and hold for 15 seconds to force restart.
Press to pause/resume during an exercise;
press and hold to end an exercise.
Press to enter the function list from home
screen.
Button Instructions
1
2
3
4
5




1
2
3
4
5
Note: Amazon Alexa is not available in all countries and regions. For more details, please check in the
70mai Health app or visit www.amazon.com/alexa-availability.
3

The screen will lock itself automatically when you start swimming; otherwise,
mistouches may be generated.
To unlock the screen, press the upper button or the lower button.
Screen Lock/Unlock
Press to swtich to the next page during an
exercise;
Press to open the shortcut (Exercise list by
default) when not in an exercise.
6
7
Button Instructions
Note: You can customize the shortcut via 70mai Health app. 6
7
4

User guide
Scan the below QR code to access the online guide. The guide provides detailed
product information including descriptions of functions. Please carefully read this
guide before use in order to avoid damage due to incorrect use.
5

How to Wear
For daily use, comfortably tighten the band around your wrist about one-finger width
away from your wrist bone. Ensure the heart rate sensor can collect data normally.
Note: Wearing the straps too loosely may impact the data collection by the heart rate sensor.
6

1. Place the watch on the charging accessory. Make sure the contact points both on the
back of the watch and the charging accessory are making contact with each other.
2. Connect the charging accessory to a standard adapter at an output voltage of 5 V
and an output current of 0.5 A or higher.
Notes:
●If the watch is unable to turn on after it has not been used for a while, it needs to be charged for about
1 minute before the charging icon is displayed.
●Wipe the watch's contact points clean before charging so as to avoid residual sweat or moisture.
Charging
7

Adjust the position of the buckle according to the circumference of your wrist. If you
need to remove the strap, refer to the figures below. Make sure you pull the strap after
attaching it to ensure the strap is installed securely.
Disassembly
Remove the strap
Install the strap
8

Name: 70mai Saphir Watch
Model: WT1004
FCC ID: 2AOK9-WT1004
Device Name: Bluetooth Device
Display Screen: 1.78 inch AMOLED
Resolution: 368 × 448
Sensor: Heart rate sensor, accelerometer, gyroscope, geomagnetic sensor, barometric
pressure sensor, ambient light sensor, capacitive sensor
Wireless Connectivity: Bluetooth 5.0 BLE
Battery Capacity: 320 mAh
Satellite Positioning: GPS & GLONASS
Compatible with: Android 4.4 & iOS 10 or above
Rated Input: 5 V 0.5 A
Item Dimensions: 50.1 × 37.3 × 9.8 mm (excluding strap and protrusions)
Specifications
9

●When using the watch to measure your heart rate, please hold your wrist still.
●The watch has a water resistance rating of 5 ATM. However, this function is not
permanent and may decline over time. The watch can be worn in the cold shower,
swimming pool, or while swimming near the shore. However, it cannot be used in a
sauna or while scuba diving.
●The screen of the watch does not support underwater operations. When the watch
comes into contact with water, use a soft cloth to wipe away excess water from its
surface before use.
●During daily use, avoid wearing the watch too tightly. Keep its contact area dry
and regularly clean the strap with water. Immediately stop using the watch and
seek medical assistance if the contact area on your skin shows signs of redness or
swelling. Due to friction, wearing the watch for a long time during high-intensity
exercise may cause skin irritation. If this is the case, please stop wearing the watch.
●Use the included charging accessory to charge the watch. Only use qualified or
certified power adapter supplied by qualified manufacturers.
●Keep the power adapter, charging accessory, and watch in a dry environment while
charging. Do not touch the power adapter or charging accessory with wet hands.
Do not expose the power adapter, charging accessory, and watch to rain or other
liquids.
●Please use the watch within a temperature range of 0°C to 45°C and store the watch
within a temperature range of -30°C to 70°C. When the ambient temperature is too
high or too low, the watch may malfunction.
●This watch is equipped with a built-in battery that cannot be removed. Do not
disassemble the watch. Do not expose batteries or battery packs to sunlight, fire,
or other conditions with extreme heat. There's a risk of explosion if the battery is
incorrectly installed. Only replace with the same or an equivalent type of battery.
Safety Precautions
10

●Do not disassemble, puncture, strike, crush or throw the battery into a fire.
●Never throw the watch or its battery into a fire so as to avoid an explosion.
●This watch is not a medical device, any data or information provided by the watch
should not be used as a basis for diagnosis, treatment, and prevention of diseases.
●The watch and its accessories may contain small parts. To avoid choking or other
hazards or damages caused by the children, keep the watch out of the reach of
children.
●This watch is not a toy and should only be used by children under adult supervision.
11

Safety information
Caution
Battery abuse or mishandling can cause overheat, liquid leakage, or an explosion. To
avoid possible injury, do the following:
●Do not open, disassemble, or service any battery.
●Do not attempt to replace the internal rechargeable lithium batteries.
●Do not crush or puncture the battery.
●Do not short-circuit the battery, or expose it to water or other liquids.
●Keep the battery away from children.
●Keep the battery away from fire.
●Do not leave the battery in an extremely high-temperature environment or an
extremely low air pressure environment.
●Stop using the battery if it is damaged, or if you notice any discharge or the buildup
of foreign materials on the battery leads. We recommend that the batteries be
charged about once every three months to prevent overcharge.
●Do not put the battery in trash that is disposed of in landfills. When disposing of the
battery, comply with local laws or regulations.
12

FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
13

WEEE Information
EU Declaration of Conformity
All products bearing this symbol are waste electrical and electronic
equipment (WEEE as in directive 2012/19/EU) which should not be
mixed with unsorted household waste. Instead, you should protect
human health and the environment by handing over your waste
equipment to a designated collection point for the recycling of waste
electrical and electronic equipment, appointed by the government
or local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and human
health. Please contact the installer or local authorities for more
information about the location as well as terms and conditions of such
collection points.
The manufacturer hereby, declares that this equipment is in
compliance with the applicable Directives and European Norms,
and amendments. The full text of the EU declaration of conformity is
available at the following internet address:
https://help.70mai.asia/1193.html
14
Service: [email protected]
For further information, please go to www.70mai.com
Manufacturer: 70mai Co., Ltd.
Address: Room2220, building2, No.588, Zixingroad, MinHangDistrict, Shanghai, China

メモ: ユーザーガイドで使用されている製品、付属品、およびユーザーインターフェイスの図は参照のみを目的
としています。製品の機能強化が行われた場合、実際の製品および機能が異なることがあります。
1. 上ボタン
2. ディスプレイ画面
3. 下ボタン
ご使用の前に本ガイドをよくお読みになり、今後の参考用に保管してください。
製品概要
充電アクセサリー
USBコネクター
2
1
3
4
5
6
7
ス マ ートウ ォッ チ
4. マイク 5. 心拍数センサーエリア
6. 接触点
7. 気圧計
15

70mai Healthアプリをダウンロードしてインストールすると、本品を管理しやすくなります。詳し
いサービスについては、70mai Healthアカウントにログインしてください。
1.上ボタンを3秒間長押しして、本品の電源をオンにします。スマートフォンでディスプレイ画面
のQRコードをスキャンし、70mai Healthアプリをダウンロードしてインストールします。
このアプリのダウンロードおよびインストールは、アプリストアまたは以下のQRコードのスキャ
ンでも可 能です。
メモ: アプリバージョンが更新されている場合があります。現行のアプリバージョンに基づいて説明に従ってくだ
さい。
2.アプリで70mai Healthアカウントにログインし、デ バイス の 追 加を選択して説明に従い、本品
を 追 加 し ま す 。
3.本品でペアリングのリクエストを許可してから、正 常 に ペ アリング され ました とアプリに 表 示
さ れ る ま で 待 っ て ペ ア リ ン グ を 完 了 さ せ ま す 。
メモ:
⿢ペアリング中は、お使いのスマートフォンでBluetoothが有効になっており、本品が接続されていることを確認し
てくだ さい 。
⿢デバイスの追加時に本品が見つからない場合や、使用時に本品に接続できない場合は、上ボタンを3秒間長押
しして出荷時設定に戻してから、再度お試しください。
接続方法
16

使用方法
画面の説明
通知の表示: ホーム画面を上から下にスワイプしま
す
コントロールパネルを開く: ホーム画面を下から上
にスワイプします
ウィジェットの切り替え: ホーム画面を左または右に
スワイプします
戻る: 他のページで左端から右にスワイプします
1
2
3
4
1秒間長押ししてAmazon Alexaを起動します。
3秒間長押しして電源をオン/オフにします。
15秒間長押しして強制的に再起動します。
押してエクササイズ中に一時停止/再開します。長押
ししてエ クサ サ イズ を 終 了 しま す 。
押してホーム画面から機能リストに移動します。
ボタン の 説 明
1
2
3
4
5




1
2
3
4
5
メモ：Amazon Alexaは一部の国および地域ではご利用いただけません。 詳細については、70mai Healthアプ
リで確認するか、www.amazon.com/alexa availabilityをご覧ください。
17

水泳を開始すると、画面は自動的にロックされます。そうしないと、誤ってタッチしてしまう場合
があるからです。
画 面 の ロックを 解 除 するに は 、上 ボタン か 下 ボタン を押します 。
画 面 の ロック / ロック 解 除
エクササイズ中に押して次のページに切り替えま
す 。
エクササイズ 以 外 のときに押してショートカット（ デ
フ ォ ル ト で は エ ク サ サ イ ズ リ ス ト ）を 開 き ま す 。
6
7
ボタン の 説 明
メモ：ショートカットは、70mai Healthアプリでカスタマイズできます。 6
7
18