A-Neuvideo ANI-16-4K60-S User manual

AUDIO / VIDEO MANUFACTURER
ANI-16-4K60-S
16x16 UHD 4K@60Hz HDR HDMI
MATRIX SWITCHER w/ Scaler
INSTRUCTION MANUAL
A-NeuVideo.com
Frisco, Texas 75036

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power o󰀨 and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS
ANEUVIDEO
1
CONTENTS
INTRODUCTION & CONTENTS ..................................................1
FEATURES & SPECIFICATIONS ................................................ 2
FRONT & REAR PANELS ............................................................3
REMOTE CONTROL ....................................................................5
RS-232 CONTROL COMMANDS / ASCII COMMANDS...........6
EDID MANAGEMENT ................................................................12
WEB GUI USER GUIDE ..........................................................14
APPLICATION EXAMPLE .........................................................20
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
The ANI-16-4K60-S 18Gbps 16x16 HDMI Matrix supports the
transmission of video (resolution up to 4K2K@60Hz YUV 4:4:4)
and multi-channel high resolution digital audio from (16) HDMI
sources to (16) HDMI displays. Audio de-embedded to coaxial
audio is supported from (16) HDMI output ports. While HDMI
output ARC function is enabled, the ARC audio from HDMI display
devices will be extracted to coaxial audio output. Each HDMI output
of this 16x16 HDMI Matrix supports 4K2K to 1080P downscaler
independently. Control via front panel buttons, IR remote, RS-232,
LAN and Web GUI. This product has a 3 year warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and
make sure the following items are contained in the shipping carton:
• ANI-16-4K60-S 16x16 UHD 4K@60Hz HDR HDMI Matrix
Switcher w/ Scaler
• 24V/3.75A Power Adapter
• IR Remote
• RS-232 serial cable (1.5M, male to female head)
• (2) Mounting Ear
• Users Guide
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
su󰀩cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2022. All Rights Reserved.
Version 1.6 JAN 2022
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATURES & SPECIFICATIONS
FEATURES
• HDMI 2.0b, HDCP 2.2/1.x and DVI 1.0 compliant
• Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI ports
• Support 18Gbps video bandwidth
• HDR, HDR10, HDR10+, Dolby Vision and HLG are supported
• Support 4K->1080P Down Scaler for each output port
• HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD Master Audio)
• Audio de-embedded is supported via coax ports
• ARC, CEC and smart EDID management are supported
• 1U rack mounted design with front panel OLED display
• Control via front panel buttons, IR remote, RS-232, LAN and Web GUI
SPECIFICATIONS
• HDMI Compliance: HDMI 2.0b
• HDCP Compliance: HDCP 2.2/1.x
• Video Bandwidth: 18Gbps
• Video Resolution: Up to 4K2K@60Hz (4:4:4)
• Color Space: RGB, YCbCr 4:4:4/4:2:2/4:2:0
• Color Depth: 8-bit, 10-bit, 12-bit
• HDMI Audio Formats (Pass-through): LPCM 2/5.1/7.1, Dolby Digital, DTS 5.1, Dolby Digital+, Dolby TrueHD, DTS-HD Master
Audio, Dolby Atmos, DTS:X
• Coax Audio Formats: LPCM 2.0, Dolby Digital / Plus, DTS 5.1
• HDR Formats: HDR10, HDR10+, Dolby Vision, HLG
• ESD Protection Human Body Model:
• ± 8kV (air-gap discharge)
• ± 4kV (contact discharge)
• Input Ports: (16) HDMI Type A [19-pin female]
• Output Ports:
• (16) HDMI Type A [19-pin female]
• (16) Coax Audio (RCA)
• Control Ports:
• TCP/IP [RJ45]
• RS-232 [D-Sub 9]
• Housing: Metal Enclosure
• Color: Black
• Dimensions (WxDxH): 19 x 7.9 x 1.7 in (440x200x44mm)
• Weight: 6.8lb / 3.1Kg
• Power Supply: Input: AC 100 - 240V 50/60Hz, Output: DC 24V/3.75A (US/EU standard, CE/FCC/ULcertied)
• Power Consumption: 76.8W
• Operating Temperature: -10°C ~ 45°C / 14°F ~ 113°F
• Storage Temperature: -20°C ~ 60°C / -4°F ~ 140°F
• Relative Humidity: 20~90% RH (non-condensing)
As product improvements are continuous, specications are subject to change without notice.
Resolution / Cable Length 4K60 4K30 1080P60
HDMI IN / OUT 16ft / 5M 32ft / 10M 50ft / 15M
The use of “Premium High Speed HDMI” cable is highly recommended.
ANEUVIDEO

3
FRONT PANEL
FRONT PANEL
qOLED SCREEN: Display matrix switching status, input / output port, EDID, Baud rate, IP Address.
wPOWER LED: The LED will illuminate in green when the product is connected to power supply, and red when the product is on
standby.
eINPUT / OUTPUT BUTTONS: You need to press input button (1~16) rstly, then press the “AV” button, nally press input button
(1~16, including “ALL”) to select the corresponding input and output ports.
rAV / ALL BUTTONS:
AV: Used to switch signal source to output.
e.g. Pressing “1→AV→3” represents signal source 1 is output to display 3.
ALL: It represents all the output ports.
e.g. Pressing “1→AV→ALL” represents signal source 1 is output to all displays.
tMENU / ENTER / UP / DOWN:
qSwitching Status Check: On the initial OLED display screen, press “MENU” button to enter the Matrix switching status interface,
then press “UP/DOWN” button to check the switching state of all ports.
wEDID Setting: On the initial OLED display screen, press “MENU” button to enter the EDID setting interface, press “UP/DOWN” button
to select the required EDID, and press the “ENTER” button. A prompt “copy to input :” will appear. Then press “UP/DOWN” button to
select the input port you need to set, and press “ENTER” button again to conrm.
eBaud Rate Setting:On the initial OLED display screen, press “MENU” button to enter the Baud rate interface, and press “UP/
DOWN” button to select the required Baud rate, nally press the “ENTER” button to conrm the setting.
rIP Address Check: On the initial OLED display screen, press “MENU” button to enter the IP interface, then press “UP/DOWN” button
to check the current IP address. Pressing the “MENU” button again will return to the initial OLED display status.
yIR WINDOW: IR receiver window, it only receives the IR remote signal from this product.
ANEUVIDEO

4
rear PANEL
REAR PANEL
qTCP/IP PORT: TCP/IP control port, connect to PC or router with an RJ45 cable.
wRS-232 PORT: Connect to a PC or control system by D-Sub 9-pin cable to transmit RS-232 command.
eAUDIO OUT (1-16): Coaxial audio output port, connect to audio output device such as audio amplier via a coaxial cable.
rDC 24V: Connect to 24V power adapter.
tGND: Connect the housing to the ground.
yINPUT PORTS (1-16): HDMI input ports, connect to HDMI source device such as DVD or set-top box with an HDMI cable.
uOUTPUT PORTS (1-16): HDMI output ports, connect to HDMI display device such as TV or monitor with an HDMI cable.
ANEUVIDEO

5
Remote Control
Remote Control
qPOWER ON OR STANDBY: Power on the Matrix or set it to standby mode.
wINPUT 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16: Select input source button.
eOUTPUT 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16: Select output source button.
rALL: Select all output sources simultaneously.
For example: when you press input “1” button and then press the “All” button, at
this time the input “1” source will be output to all display devices.
OPERATION INSTRUCTIONS:
You need to press the input button rstly and then press output button.
For example: Press Input-Y (Y means input button from 1 to 16)
Then press Output-X (X means output button from 1 to 16, including “All” button)
IR CODES
CUSTOM CODE: 08F7
POWER 08F7 4D INPUT 13 08F7 55 OUTPUT 10 08F7 44
INPUT 1 08F7 09 INPUT 14 08F7 57 OUTPUT 11 08F7 50
INPUT 2 08F7 54 INPUT 15 08F7 4E OUTPUT 12 08F7 0E
INPUT 3 08F7 47 INPUT 16 08F7 17 OUTPUT 13 08F7 13
INPUT 4 08F7 42 OUTPUT 1 08F7 4C OUTPUT 14 08F7 12
INPUT 5 08F7 08 OUTPUT 2 08F7 0D OUTPUT 15 08F7 15
INPUT 6 08F7 48 OUTPUT 3 08F7 56 OUTPUT 16 08F7 53
INPUT 7 08F7 4B OUTPUT 4 08F7 16 OUTPUT ALL 08F7 18
INPUT 8 08F7 43 OUTPUT 5 08F7 40
INPUT 9 08F7 0C OUTPUT 6 08F7 10
INPUT 10 08F7 19 OUTPUT 7 08F7 11
INPUT 11 08F7 0F OUTPUT 8 08F7 52
INPUT 12 08F7 03 OUTPUT 9 08F7 4F
ANEUVIDEO

6
RS-232 Control CommandS
Serial port protocol
BAUD RATE: 115200 IP PROTOCOL:
DATA BITS: 8 TCP/IP PORT: 65280
STOP BITS: 1 TELNET PORT: 23
CHECK BIT: 0
RS-232 CONFIGURATION
RS-232 cable is a straight thru cable and not null-modem
Denition Pin Pin Denition
1 1 DCD
TX 2 2 RX
RX 3 3 TX
4 4 DTR
GND 5 5 GND
6 6 DSR
7 7 RTS
8 8 CTS
9 9 RI
RS-232
ANEUVIDEO
Device PC

7
ASCII CommandS
Then, open a Serial Command tool on PC to send ASCII command to control the Matrix. The ASCII command list about the product is
shown as below.
SERIAL PORT PROTOCOL
Baud rate: 115200
Data bits: 8bit
Stop bits: 1
Check bit: 0
POWER
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s power z! POWER ON/OFF THE DEVICE, Z=0~1
(Z=0 POWER OFF, Z=1 POWER ON)
s power 1! Power on
System Initializing...
Initialization Finished!
FW version x.xx.xx
POWER ON
r power! GET CURRENT POWER STATE r power! Power ON/Power OFF
s reboot! REBOOT THE DEVICE s reboot! Reboot...
System Initializing...
Initialization Finished!
FW version x.xx.xx
SYSTEM SETUP
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
help! LIST ALL COMMANDS help!
r type! GET DEVICE MODEL r type! ANI-16-4K-S
r status! GET DEVICE CURRENT STATUS r status! Get the unit all status:
power, beep, lock, in/out
connection, video/audio
crosspoint, edid, scaler,
network status
r fw version! GET FIRMWARE VERSION r fw version! MCU BOOT: VX.XX.XX
MCU APP: VX.XX.XX
WEB GUI: VX.XX
r link in x! GET THE CONNECTION STATUS OF THE
X INPUT PORT, X=0~16 (0=ALL)
r link in 1! HDMI Input 1: Connect
r link out y! GET THE CONNECTION STATUS OF THE
Y OUTPUT PORT, Y=0~16 (0=ALL)
r link out 1! HDMI Input 1: Connect
s reset! RESET TO FACTORY DEFAULTS s reset! Reset to factory defaults
System Initializing...
Initialization Finished!
FW version x.xx.xx
s beep z! ENABLE/DISABLE BUZZER FUNCTION,
Z=0~1 (Z=0 BEEP OFF, Z=1 BEEP ON)
s beep 1! BEEP ON
BEEP OFF
BEEP ON
r beep! GET BUZZER STATE r beep! BEEP ON
BEEP OFF
s lock z! LOCK/UNLOCK FRONT PANEL BUTTON,
Z=0~1 (Z=0 LOCK OFF, Z=1 LOCK ON)
s lock 1! Panel Button: LOCK ON /
LOCK OFF
Panel Button:
LOCK OFF
r lock! GET PANEL BUTTON LOCK STATE r lock! Panel Button: LOCK ON/
OFF
s lcd on time z! SET LCD SCREEN REMAIN ON TIME,
Z=0~4 (0:OFF, 1:ALWAYS ON, 2:15S, 3:30S, 4:60S)
s lcd on time 1! LCD ON 15 seconds LCD ON 30
seconds
r lcd mode! GET THE BACKLIGHT STATUS OF LCD SCREEN r lcd mode! LCD ALWAYS ON
ANEUVIDEO

8
ASCII CommandS
s save preset z! SAVE SWITCH STATE BETWEEN ALL OUTPUT
PORT AND THE INPUT PORT TO PRESET Z,
Z=1~8
s save preset 1! Save to Preset 1
s recall preset z! CALL SAVED PRESET Z SCENARIOS, Z=1~8 s recall preset 1! Recall from Preset 1
s clear preset z! CLEAR STORED PRESET Z SCENARIOS, Z=1~8 s clear preset 1! Clear Preset 1
r preset z! GET PRESET Z INFORMATION, Z=1~8 r preset 1! Video/Audio Crosspoint
OUTPUT SETTING
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s in x av out y! SET INPUT X TO OUTPUT Y,
X=1~16, Y=0~16 (0=ALL)
s in 1 av out 2! INPUT 1 -> OUTPUT 2 PTP
r av out y! GET OUTPUT Y SIGNAL STATUS
Y=0~16 (0=ALL)
r av out 0! INPUT 1 -> OUTPUT 1
…… INPUT 16 ->
OUTPUT 16
s hdmi y stream
z!
SET OUTPUT Y STREAM ON/OFF,
Y=0~16 (0=ALL)
Z=0~1 (0:DISABLE, 1:ENABLE)
s hdmi 1 stream 1!
s hdmi 0 stream 1!
Enable HDMI Output 1
stream
Disable HDMI Output 1
stream
Enable HDMI all outputs
stream
Disable HDMI all
outputs stream
ENABLE
r hdmi y stream! GET OUTPUT Y STREAM STATUS,
Y=0~16 (0=ALL)
r hdmi 1 stream! Enable HDMI Output 1
stream
s hdmi y scaler z! SET HDMI OUTPUT Y PORT OUTPUT SCALER
MODE,
Y=0~16 (0=ALL), Z=1~3 (1=BYPASS, 2=4K->1080P,
3=AUTO)
s hdmi 1 scaler 1!
s hdmi 0 scaler 1!
HDMI Output 1 set to
bypass mode
HDMI ALL Outputs set to
bypass mode
HDMI ALL
OUTPUTS
SET TO BYPASS
MODE
r hdmi y scaler! GET HDMI OUTPUT Y PORT OUTPUT MODE
Y=0~16 (0=ALL)
r hdmi 1 scaler ! HDMI Output 1 set to
bypass mode
s edid in x from z! SET INPUT X EDID FROM DEFAULT EDID Z,
X=0~16 (0=ALL), Z=1~39
1. 1080P, STEREO AUDIO 2.0
2. 1080P, DOLBY/DTS 5.1
3. 1080P, HD AUDIO 7.1
4. 1080I, STEREO AUDIO 2.0
5. 1080I, DOLBY/DTS 5.1
6. 1080I, HD AUDIO 7.1
7. 3D, STEREO AUDIO 2.0
8. 3D, DOLBY/DTS 5.1
9. 3D, HD AUDIO 7.1
10. 4K2K30_444,STEREO AUDIO 2.0
11. 4K2K30_444,DOLBY/DTS 5.1
12. 4K2K30_444,HD AUDIO 7.1
13. 4K2K60_420,STEREO AUDIO 2.0
14. 4K2K60_420,DOLBY/DTS 5.1
15. 4K2K60_420,HD AUDIO 7.1
16. 4K2K60_444,STEREO AUDIO 2.0
17. 4K2K60_444,DOLBY/DTS 5.1
18. 4K2K60_444,HD AUDIO 7.1
19. 4K2K60_444,STEREO AUDIO 2.0 HDR
20. 4K2K60_444,DOLBY/DTS 5.1 HDR
21. 4K2K60_444,HD AUDIO 7.1 HDR
22. USER1
23. USER2
24. COPY FROM HDMI OUTPUT 1
s edid in 1 from 1!
s edid in 0 from 1!
Input 1 EDID:1080p,
Stereo Audio 2.0
ALL Inputs EDID: 1080p,
Stereo Audio 2.0
1080P, STEREO
AUDIO 2.0
ANEUVIDEO

9
ASCII CommandS
EDID SETTING
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s edid in x from z! 25. COPY FROM HDMI OUTPUT 2
26. COPY FROM HDMI OUTPUT 3
27. COPY FROM HDMI OUTPUT 4
28. COPY FROM HDMI OUTPUT 5
29. COPY FROM HDMI OUTPUT 6
30. COPY FROM HDMI OUTPUT 7
31. COPY FROM HDMI OUTPUT 8
32. COPY FROM HDMI OUTPUT 9
33. COPY FROM HDMI OUTPUT 10
34. COPY FROM HDMI OUTPUT 11
35. COPY FROM HDMI OUTPUT 12
36. COPY FROM HDMI OUTPUT 13
37. COPY FROM HDMI OUTPUT 14
38. COPY FROM HDMI OUTPUT 15
39. COPY FROM HDMI OUTPUT 16
r edid in x! GET EDID STATUS OF THE INPUT X,
X=0~16 (0=ALL INPUT)
r edid in 0! Input 1 EDID: K2K60_444,
Stereo Audio 2.0
Input 2 EDID: K2K60_444,
Stereo Audio 2.0
Input 3 EDID: K2K60_444,
Stereo Audio 2.0
Input 4 EDID: K2K60_444,
Stereo Audio 2.0
r edid data hdmi
y!
GET THE EDID DATA OF THE HDMI OUTPUT Y
PORT, Y=1~16
r edid data hdmi 1! EDID: 00 FF FF FF FF
FF FF 00 ………
AUDIO SETTING
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s hdmi y arc z! TURN ON/OFF ARC OF HDMI OUTPUT Y,
Y=0~16 (0=ALL)
Z=0~1 (Z=0, OFF, Z=1 ON)
s hdmi 1 arc 1!
s hdmi 0 arc 1!
HDMI Output 1 ARC ON
HDMI Output 1 ARC OFF
HDMI ALL Output ARC ON
HDMI ALL Output ARC OFF
r hdmi y arc! GET THE ARC STATE OF HDMI OUTPUT Y,
Y=0~16 (0=ALL)
r hdmi 1 arc! HDMI Output 1 ARC ON OFF
CEC SETTING
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s cec in x on! SET INPUT X POWER ON BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 on! Input 1 POWER ON
s cec in x o󰀨! SET INPUT X POWER OFF BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 o󰀨! Input 1 POWER OFF
s cec in x menu! SET INPUT X OPEN MENU BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 menu! Input 1 OPEN MENU
s cec in x back! SET INPUT X BACK OPERATION BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 back! Input 1 BACK
OPERATION
s cec in x up! SET INPUT X MENU UP OPERATION BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 up! Input 1 MENU UP
OPERATION
s cec in x down! SET INPUT X MENU DOWN OPERATION BY
CEC, X=0~16 (0=ALL INPUT)
s cec in 1 down! Input 1 MENU DOWN
OPERATION
s cec in x left! SET INPUT X MENU LEFT OPERATION BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 left! Input 1 MENU LEFT
OPERATION
ANEUVIDEO

10
ASCII CommandS
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
s cec in x right! SET INPUT X MENU RIGHT OPERATION BY
CEC, X=0~16 (0=ALL INPUT)
s cec in 1 right! Input 1 MENU RIGHT
OPERATION
s cec in x enter! SET INPUT X MENU ENTER BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 enter! Input 1 MENU ENTER
OPERATION
s cec in x play! SET INPUT X PLAY BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 play! Input 1 PLAY
OPERATION
s cec in x pause! SET INPUT X PAUSE BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 pause! Input 1 PAUSE
OPERATION
s cec in x stop! SET INPUT X STOP BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 stop! Input 1 STOP
OPERATION
s cec in x rew! SET INPUT X REWIND BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 rew! Input 1 REWIND
OPERATION
s cec in x mute! SET INPUT X VOLUME MUTE BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 mute! Input 1 VOLUME MUTE
s cec in x vol-! SET INPUT X VOLUME DOWN BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 vol-! Input 1 VOLUME DOWN
s cec in x vol+! SET INPUT X VOLUME UP BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 vol+! Input 1 VOLUME UP
s cec in x 󰀨! SET INPUT X FAST FORWARD BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 󰀨! Input 1 FAST FORWARD
OPERATION
s cec in x
previous!
SET INPUT X PREVIOUS BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 previous! Input 1 PREVIOUS
OPERATION
s cec in x next! SET INPUT X NEXT BY CEC,
X=0~16 (0=ALL INPUT)
s cec in 1 next! Input 1 NEXT
OPERATION
s cec hdmi out y
on!
SET HDMI OUTPUT Y POWER ON BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1 on! HDMI Output 1 POWER
ON
s cec hdmi out
y o󰀨
SET HDMI OUTPUT Y POWER OFF BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1 on! HDMI Output 1 POWER
OFF
s cec hdmi out y
mute!
SET HDMI OUTPUT Y VOLUME MUTE BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1 mute! HDMI Output 1 VOLUME
MUTE
s cec hdmi out y
vol-!
SET HDMI OUTPUT Y VOLUME DOWN BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1 vol-! HDMI Output 1 VOLUME
DOWN
s cec hdmi out y
vol+!
SET HDMI OUTPUT Y VOLUME UP BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1 vol+! HDMI Output 1 VOLUME
UP
s cec hdmi out y
active!
SET HDMI OUTPUT Y ACTIVE SOURCE BY CEC,
Y=0~16 (0=ALL OUTPUT)
s cec hdmi out 1
active!
HDMI Output 1 ACTIVE
SOURCE
NETWORK SETTING
COMMAND
CODE DESCRIPTION EXAMPLE FEEDBACK DEFAULT SETTING
r ipcong! GET THE CURRENT IP CONFIGURATION ipcong! IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port= 8000
Telnet port= 10
Mac address:
00:1C:91:03:80:01
r mac addr! GET NETWORK MAC ADDRESS r mac addr! MAC ADDRESS:
00:1C:91:03:80:01
ANEUVIDEO

11
ASCII CommandS
s ip mode z! SET NETWORK IP MODE TO STATIC IP OR
DHCP, Z=0~1 (Z=0 STATIC, Z=1 DHCP )
s ip mode 0! Set IP mode: Static
(Please use “s net
reboot!” command or
repower device to apply
new cong!)
r ip mode! GET NETWORK IP MODE r ip mode! IP Mode: Static
s ip addr
xxx.xxx.xxx.xxx!
SET NETWORK IP ADDRESS s ip addr
192.168.1.100!
Set IP address:
192.168.1.100 (Please
use “s net reboot!”
command or repower
device to apply new
cong!)
DHCP ON, Device can’t
cong static address,
set DHCP o󰀨 rst.
r ip addr! GET NETWORK IP ADDRESS r ip addr! IP address: r ip addr!
192.168.1.100
s subnet
xxx.xxx.xxx.xxx!
SET NETWORK SUBNET MASK s subnet
255.255.255.0!
Set Subnet Mask:
255.255.255.0
(Please use “s net
reboot!” command or
repower device to apply
new cong!)
DHCP ON, Device can’t
cong subnet mask,
set DHCP o󰀨 rst.
r subnet! GET NETWORK SUBNET MASK r subnet! Subnet Mask:
255.255.255.0
s gateway
xxx.xxx.xxx.xxx!
SET NETWORK GATEWAY s gateway
192.168.1.1!
Set gateway: 192.168.1.1
Please use “s net
reboot!” command or
repower device to
apply new cong!
DHCP ON, Device can’t
cong gateway, set
DHCP o󰀨 rst.
r gateway! GET NETWORK GATEWAY r gateway! Gateway:192.168.1.1
s tcp/ip port x! SET NETWORK TCP/IP PORT (X=1~65535) s tcp/ip port 8000! Set TCP/IP port: 8000
r tcp/ip port! GET NETWORK TCP/IP PORT r tcp/ip port! TCP/IP port: 8000
s telnet port x! SET NETWORK TELNET PORT (X=1~65535) s telnet port 23! Set Telnet Port: 23
r telnet port! GET NETWORK TELNET PORT r telnet port! Telnet Port: 23
s net reboot! REBOOT NETWORK MODULES s network reboot! Network Reboot…
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP Port= 8000
Telnet port= 10
Mac address:
00:1C:91:03:80:01
ANEUVIDEO

12
EDID Management
EDID Management
This Matrix has 21 factory dened EDID settings, 2 user-dened EDID modes and 16 copy EDID modes. You can select dened EDID
mode or copy EDID mode to input port through front panel buttons, RS-232 control or Web GUI.
On-Panel Button Operation: On the initial OLED display screen, press “MENU” button to enter the EDID setting interface, press “UP/
DOWN” button to select the required EDID, and press the “ENTER” button. A prompt “copy to input :” will appear. Then press “UP/
DOWN” button to select the input port you need to set, and press “ENTER” button again to conrm this operation.
RS-232 Control Operation: Connect the Matrix to PC with a serial cable, then open a Serial Command tool on PC to send ASCII
command “s edid in x from z!” to set EDID. For details, please refer to “EDID Setting” in the ASCII command list of “9. RS-232 Control
Command”.
Web GUI Operation: Please check the EDID management in the “Input Page” further in this User Guide.
The dened EDID setting list of the product is shown as below:
EDID MODE EDID DESCRIPTION
1 1080p, Stereo Audio 2.0
2 1080p, Dolby/DTS 5.1
3 1080p, HD Audio 7.1
4 1080i, Stereo Audio 2.0
5 1080i, HD Audio 7.1
6 1080i, Dolby/DTS 5.1
7 3D, Stereo Audio 2.0
8 3D, Dolby/DTS 5.1
9 3D, HD Audio 7.1
10 4K2K30_444, Stereo Audio 2.0
11 4K2K30_444, Dolby/DTS 5.1
12 4K2K30_444, HD Audio 7.1
13 4K2K60_420, Stereo Audio 2.0
ANEUVIDEO

13
EDID Management
EDID MODE EDID DESCRIPTION
14 4K2K60_420, Dolby/DTS 5.1
15 4K2K60_420, HD Audio 7.1
16 4K2K60_444, Stereo Audio 2.0
17 4K2K60_444, Dolby/DTS 5.1
18 4K2K60_444, HD Audio 7.1
19 4K2K60_444, Stereo Audio 2.0 HDR
20 4K2K60_444, Dolby/DTS 5.1 HDR
21 4K2K60_444, HD Audio 7.1HDR
22 USER1
23 USER2
24 Copy from HDMI Output 1
25 Copy from HDMI Output 2
26 Copy from HDMI Output 3
27 Copy from HDMI Output 4
28 Copy from HDMI Output 5
29 Copy from HDMI Output 6
30 Copy from HDMI Output 7
31 Copy from HDMI Output 8
32 Copy from HDMI Output 9
33 Copy from HDMI Output 10
34 Copy from HDMI Output 11
35 Copy from HDMI Output 12
36 Copy from HDMI Output 13
37 Copy from HDMI Output 14
38 Copy from HDMI Output 15
39 Copy from HDMI Output 16
ANEUVIDEO

14
Web GUI User Guide
The Matrix can be controlled by Web GUI. The operation method is shown as below:
STEP 1: Get the current IP Address. The default IP address is 192.168.1.100. You can get the current Matrix IP address in two ways:
THE FIRST WAY: You can get the IP address via panel buttons. On
the initial OLED display, press “MENU” button to enter the IP interface,
then press “UP/DOWN” button to check the current IP address.
THE SECOND WAY: You can get the IP address via RS-232 control.
Send the command “ r ipcong!” through an ASCII Command tool,
then you’ll get the feedback information as shown.
IP: 192.168.62.100 in the above gure is the IP Address of the Matrix
(the IP address is variable, depending on what the specic machine
returns). For the details of ASCII control, please refer to “RS-232
Control Command”.
STEP 2: Set the IP address of the PC to be in the same network segment with the Matrix.
STEP 3: Input the IP address of the Matrix into your browser on the PC to enter Web GUI page.
After entering the Web GUI page, there will be a Login page, as
shown.
Select the Username from the list and enter the password. The
default passwords are:
Username: User Admin
Password: user admin
After entering the password, click the “LOGIN” button and the
following Status page will appear.
Status Page
ANEUVIDEO

15
Web GUI User Guide
SWITCH Page
You can do the following operations on the Switch page:
qOUTPUT: The current device’s OUTPUT port. You can select signal source for it.
wALL OUTPUT: All OUTPUT ports for the current device. You can select signal source for them.
eINPUT: You can click the drop-down menu to select signal source for the corresponding OUTPUT port .
rPRESETS NAME: You can name the current scene with maximum length of 12 characters (Chinese name is unsupported).
tPRESETS SET: You can restore the settings of the last saved audio-video matrix switching relationship.
yPRESETS SAVE: You can save audio-video matrix switching relationship.
uPRESETS CLEAR: You can clear the saved audio-video matrix switching relationship.
Input Page
ANEUVIDEO

16
Web GUI User Guide
You can do the following operations on the Input page:
qINPUTS: Input channel of the device.
wACTIVE: It indicates whether the channel is connected to a signal source.
eNAME: The input channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box
(Chinese name is unsupported).
rEDID: You can set the current channel’s EDID. The specic operation is as follows:
Set EDID for the User:
Click the “Browse” button, then select the bin le. If you select the wrong EDID le,
there will be a prompt, as shown in the following gure.
Make sure to select the correct le, then you can check the name of the selected
le. Select “User 1” or “User 2”, then click “Upload”. After successful setting, it
will prompt as follows.
Download the EDID File of the Corresponding Input Channel:
Click the drop-down box of “Select EDID File” to select the corresponding input
channel. Then click “Download” to download the corresponding EDID le.
Output Page
You can do the following operations on the Output page:
qOUTPUTS: Output channel of the device.
wNAME: The current output channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the
input box.
eCABLE: It indicates the connection status of output ports. When the output port is connected to the display, it shows green, otherwise,
it shows gray.
ANEUVIDEO

17
Web GUI User Guide
rSCALAR MODE: Set the current output resolution mode.
tARC: Turn on/o󰀨 the ARC function.
ySTREAM: Turn on/o󰀨 the output stream.
CEC Page
You can perform CEC management on this page:
qINPUT CONTROL: You can control the operation of each input source by clicking the icons on the page.
wOUTPUT CONTROL: You can control the operation of each display, such as power on/o󰀨, volume +/-, active source switching.
Network Page
Set the Default Network:
Click “Set Network Defaults”, there will be a prompt, as shown in the following
gure.
ANEUVIDEO

18
Web GUI User Guide
Click “OK” to search the IP Address again, as shown in the following gure.
After searching is completed, it will switch to the login page, the default network setting is completed.
Modify Username:
Click the “User” button, enter the correct Old Password, New Password, and
Conrm Password, then click “Save”. After successful modication, there will be
a prompt, as shown in the following gure.
NOTE: Input rules for changing passwords:
1. The password can’t be empty.
2. New Password can’t be the same as Old Password.
3. New Password and Conrm Password must be the same.
Modify Network Setting:
Modify the Mode/IP Address/Gateway/Subnet Mask/
Telnet Port as required, click “Save” to save the
settings, then it will come into e󰀨ect.
After modication, if the Mode is “Static”, it will switch to
the corresponding IP Address; if the Mode is “DHCP”,
it will automatically search and switch to the IP Address
assigned by the router.
NOTE: Setting Telnet port to “0” disables any Telnet
access.
ANEUVIDEO